Installation Instructions

ManualsBrandsElectrolux ManualsCookingElectrolux Stainless Steel 30 Inch Microwave Trim Kit

Installation

Instructions

Built-in Trim Kit

Model #

BEFORE YOU BEGIN

•

IMPORTANT – Save these instructions

for local inspector's use.

•

IMPORTANT

– Observe all governing

codes and ordinaces.

•

Note to Installer

– Be sure to leave

these instructions with the Consumer.

•

Note to Consumer – Keep these

instructions for future reference.

• Skill level - Installation of this appliance

requires basic mechanical and electrical

skills.

Read these instructions completely and carefully.

• Proper installation is the responsibility of the

installer.

• Product failure due to improper installation is

not covered under the Warranty.

• Unplug the microwave oven before

attempting installation of this kit.

• Because the kit includes metal

parts, caution

should be used in handling and installation to

avoid the possibility of injury.

• Do not remove permanently affixed labels,

warnings, or plates from the product. This

may void the warranty.

FOR YOUR SAFETY:

WARNING – Before beginning the installation,

switch power off at service panel and lock out

When the service

cannot be locked, securely

fasten

a prominent warning device,

such as a tag, to

the service panel.

IMPORTANT - PLEASE READ

AND FOLLOW

THIS BUILT-IN KIT IS DESIGNED FOR USE

ONLY WITH ELECTROLUX MICROWAVE

OVENS SPECIFYING BUILT-IN KIT

QUESTIONS?

For customers in the United States call:1-800-374-4432

For customers in Canada call: 1-800-265-8352

Visit our Website at:

www.electroluxappliances.com

READ CAREFULLY.

KEEP THESE INSTRUCTIONS.

to prevent being switched on accidentally.

PN:

Nov. 2020

EMTK3011AS

A06822909

EN-1

Summary of content (6 pages)

PAGE 1
Installation Instructions BEFORE YOU BEGIN • Built-in Trim Kit Model # EMTK3011AS Read these instructions completely and carefully. IMPORTANT – Save these instructions • IMPORTANT – Observe all governing • for local inspector's use. • • • • codes and ordinaces. • these instructions with the Consumer. • Note to Installer – Be sure to leave Note to Consumer – Keep these instructions for future reference.
PAGE 2
Installation Instructions PARTS INCLUDED IN THE KIT 1. Front Frame Assembly- QTY 1 2. Exhaust Duct - QTY 1 3. Rail – QTY 2 4. Screw A - Short Screws - QTY 11 + 3 extra Screw A - Short Screws 5. Screw B - Long Screws - QTY 4 + 2 extra 6. Rear Duct CHOOSING A LOCATION FOR YOUR MICROWAVE OVEN IF BUILT-IN Screw B - Long Screws Front Frame Assembly Built-In Trim Kit allows for the installation of microwaves listed below to be built into a cabinet or wall by itself or over an electric wall oven*.
PAGE 3
Installation Instructions Screw A- Short Screws Center Line Illustration 3 ELECTRICAL OUTLET LOCATION Illustration 4 EXHAUST DUCT ASSEMBLY Outlet should NOT be in the shaded area as indicated on Illustration 3 1. Draw a Central Line on floor. Place the Exhaust Duct in the opening，When the Exhaust Duct Assembly is in the opening correctly, the Center Line is in the middle of the Exhaust Duct Assembly. See Illustration 4. 2. Secure the Exhaust Duct Assembly with the three screw A - short screws.
PAGE 4
Installation Instructions 1 LOCATE AND INSTALL THE EXHAUST DUCT S et Exhaust Duct into the front cabinet microwave oven cutout and center it right and left. Push back until the front flange is against the cabinet front wall. Mount the Exhaust Duct using 3 screw A - short screws. 3 INSTALL THE REAR DUCT 1. Gently return microwave oven to its upright position. 2. Remove screw A-short screw. Screw AShort Screws Screw A -short screw 3. Align the rear duct with the back of microwave oven, as shown.
PAGE 5
Installation Instructions 5 SECURE THE RAILS TO THE CABINET 3 INSTALL THE REAR DUCT (continued) 6. Use 3 srew A -short screws to secure back of rear duct to the back of microwave oven, as shown. E nsure the Exhaust Duct and Bottom Bracket front flanges are tight against the cabinet, and that the screws holes are aligned. Drive 4 screw A - short screws through the Exhaust Duct and Rails into the cabinet Mounting Holes A B C A. Screw A -short screws (3) B. Rear duct C.
PAGE 6
Installation Instructions FRONT FRAME INSTALLATION 1. 2. Position the FRONT FRAME ASSEMBLY to be square with the oven. Carefully place the FRONT FRAME ASSEMBLY on the oven. See Illustration 6. Check that it is level and then secure with two Screws B - long screws Secure the bottom portion of the FRONT FRAME ASSEMBLY with the two remaining Screws B - long screws. See Illustration 7.