User manual

2
IMPORTANT SAFETY INFORMATION
It is most important that this instruction book should be retained with the appliance for future
reference. Should the appliance be sold or transferred to another owner, or should you move house and
leave the appliance, always ensure that the book is left with the appliance in order that the new owner
can get to know the functioning of the appliance and the relevant safety information.
This information has been provided in the interest of safety. You MUST read it carefully before installing
or using the appliance.
Installation
¥ This appliance is heavy. Care should be taken
when moving it.
¥ It is dangerous to alter the specifications or
attempt to modify this product in any way.
¥ Care must be taken to ensure that the appliance
does not stand on the electrical supply cable. If
the supply cable is damaged, it must be replaced
by a special cord available from your local
Service Force Centre.
¥ Any electrical work required to install this
appliance should be carried out by a qualified
electrician or competent person.
¥ Parts which heat up should not be exposed.
Whenever possible, the back of the appliance
should be close to a wall but leaving the required
distance for ventilation as stated in the installation
instructions.
¥ The appliance should be left for 2 hours after
installation before it is turned on, in order to allow
the refrigerant to settle.
Child Safety
¥ Do not allow children to tamper with the controls
or play with the product.
¥ Keep all packaging well away from children.
During Use
¥ This appliance is designed for domestic use only,
specifically for the storage of edible foodstuffs.
¥ Frozen food must NOT be re-frozen once it has
thawed out.
¥ Do not place carbonated or fizzy drinks in the
freezer.
¥ Do not remove items from the freezer if your
hands are damp/wet, as this could cause skin
abrasions or frost/freezer burns.
¥ Ice lollies can cause Ôfrost/freezer burnsÕ if
consumed straight from the freezer.
¥ ManufacturersÕ storage recommendations should
be strictly adhered to. Refer to relevant
instructions.
Maintenance and Cleaning
¥ Switch off and unplug the appliance before
carrying out any cleaning or maintenance work.
Servicing
¥ This product should be serviced by an authorised
engineer and only genuine spare parts should be
used.
¥ Under no circumstances should you attempt to
repair the machine yourself. Repairs carried out
by inexperienced persons may cause injury or
serious malfunctioning. Refer to your local
Electrolux Service Force Centre and always insist
on genuine spare parts.
At the end of the Appliance
Life
¥ When disposing of your appliance, use an
authorised disposal site.
¥ Remove the plug and ensure that any locks or
catches are removed, to prevent young children
being trapped inside.
19
Door reversal directions
1. Disconnect from the electricity supply.
2. Remove all loose items, including food, store food
in a cool place.
3. Gently lay the fridge/freezer on its back with the
top held away from the floor by 5-8 cm (2-3
inches) of packing.
4. Remove the feet (B).
5. Remove bottom hinge (A).
6. Remove the freezer door by releasing it from the
middle hinge (C).
7. Unscrew the middle hinge.
8. Slide out the fridge door from pin (D), unscrew pin
(D) and then screw it down into the hinge
provided on the opposite side, after having
removed the small plugs (I) which should then be
fitted on the opposite side.
9. Remove blanking plug (E).
10.Remove door closure device (F) from the upper
door and refit it on the opposite side of the bottom
door.
11.Remove door closure device (F) from the bottom
door and refit it on the opposite side of the upper
door.
12.Refit the blanking plug (E) on the opposite side.
13.Refit the fridge door and replace the middle hinge
to the left hand side.
14.Replace the door and bottom hinge (A) on the
opposite side.
15.Refit the feet (B).
Attention
After completion of the door reversing operation,
check that the door gasket adheres to the cabinet. If
the ambient temperature is cold (i.e. in Winter), the
gasket may not fit perfectly to the cabinet. In that
case, wait for the natural fitting of the gasket or
accelerate this process by heating up the part
involved with a normal hairdryer on a low setting.
D752
E
F
D715
A
B
B
I
I
I
D
D590
PR24/2
C
Door closure device
The appliance is provided with a door closure device
which guarantees correct closing of the doors.
Remove blanking plugs E and transfer the closure
device F to the opposite door position and refit the
blanking plugs into the vacant holes.