User manual

8
MAINTENANCE
Unplug the appliance before carrying out
any maintenance operation.
Periodic cleaning
Clean the inside with warm water and bicarbonate of
soda.
Rinse and dry thoroughly.
Clean the condenser (black grill) and the
compressor at the back of the appliance with a
brush or a vacuum cleaner. This operation will
improve the performance of the appliance and save
electricity consumption.
Many proprietary kitchen surface cleaners
contain chemicals that can attack/damage the
plastics used in this appliance. For this reason it
is recommended that the outer casing of this
appliance is only cleaned with warm water with a
little washing-up liquid added.
Periods of non-operation
When the appliance is not in use for long periods,
take the following precautions:
remove the plug from the wall socket;
remove all food;
defrost and clean the interior and all accessories;
leave the door ajar to allow air to circulate to prevent
unpleasant smells.
Interior light
The light bulb inside the refrigerator compartment
can be reached as follows:
- unscrew the light cover securing screw.
- unhook the moving part as shown in the figure.
If the light does not come on when the door is open,
check that it is screwed into place properly. If it still
does not light up, change the bulb.
The rating is shown on the light bulb cover.
Defrosting
Frost is automatically eliminated from the evaporator
of the refrigerator compartment every time the motor
compressor stops, during normal use. The defrost
water drains out through a trough into a special
container at the back of the appliance, over the
motor compressor, where it evaporates.
It is important to periodically clean the defrost
water drain hole in the middle of the refrigerator
compartment channel to prevent the water
overflowing and dripping onto the food inside.
Use the special cleaner provided, which you will
find already inserted into the drain hole.
The freezer compartment, however, will become
progressively covered with frost. This should be
removed with a plastic scraper, whenever the
thickness of the frost exceeds 4 mm. During this
operation it is not necessary to switch off the power
supply or to remove the foodstuffs.
D037
D411
21
Kap› yönünün de¤ifltirilmesi
Herhangi fiflibir ifllem yapmadan önce buzdolabının
fiflini çekin.
Kap› yönünü de¤ifltirmek için, flu yollar› izleyin:
1. Tak›l› olan havaland›rma ›zgaras›n› (D) d›fla
çekin.
2. Deli¤in kapa¤›n› (G) ve alt mentefleyi (E) üç
viday› da sökerek ç›kart›n.
3. Alt kapa¤› orta mentefleden kayd›rarak ç›kart›n.
4. Orta mentefleyi ( H) sökün.
5. Buzdolab› kap›s›n› üst mentefle piminden (G)
kurtararak ç›kart›n.
6. Pimi (G) çıkartın ve di¤er tarafa takılması
gereken tapaları çıkarttıktan sonra pimi aksi
tarafa takın.
7. Kapının iki tapasını (varsa) mentefle pimleri
deliklerini açarak çıkartın ve aksi tarafa takın,
daha sonra üst kapıyı takın.
8. Orta mentefleyi de di¤er tarafa monte edin.
9. 10 mm'lik bir ‹ngiliz anahtar› kullanarak mentefle
pimini sökün (E) ve menteflenin di¤er taraf›na
monte edin.
10. Alt kap›y› da monte edin.
11. Söktü¤ünüz vidalar› kullanarak alt mentefleyi (E)
karfl› kenara monte edin. Delik t›pas›n› (G) alt
mentefleye takın. Ok istikametinde iterek delik
t›pas›n› (F) havaland›rma ›zgaras›ndan (D)
kayd›r›p ç›kar›n ve karfl› tarafa monte edin.
12. Havaland›rma ›zgaras›n› (D) tekrar yerine
oturtun.
13.Tutma yerlerini sökün ve di¤er tarafa tak›n. Aç›k
kalan delikleri malzeme pofletindeki t›palarla
kapat›n.
Kap›lar orta mentefleyi ayarlayarak hizalanabilir.
Orta mentefle, iki vida gevfletildikten sonra bir alet
yard›m›yla yatay olarak ayarlanabilir.
Uyar›:
Kap›lar›n aç›lma yönünü de¤ifltirdikten sonra
tüm vidalar›n düzgün bir flekilde s›k›ld›¤›ndan ve
manyetik lasti¤in buzdolab›n›n gövdesine
yap›flt›¤›ndan emin olunuz. Ortam s›cakl›¤›
düflükse (örne¤in k›fl aylar›nda) conta
buzdolab›n›n gövdesine tam olarak
oturmayabilir. Bu durumda contan›n
kendili¤inden oturmas›n› bekleyiniz ya da ilgili
parçayı bir saç kurutma makinesi ile ısıtarak bu
ifllemi hızlandırınız.
H
PR228
G