Contents For the Installer For the User Safety information 3 Description of the appliance 4-5 Technical specifications 13 Unpacking 14 - Damages - Use - Protecting the machine against freezing - Rinse conditioner dispenser - Spray arm - Coarse filter - Fine filter - Detergent dispenser - Salt container Installation The control panel 6 - Audible signals Adjusting the water softener 7 Loading the dishwasher 8 Rukowodstwo po \kspluatacii - How to load the dishes Programme chart 9 Using t
Safety information Before installing and first using the dishwasher, read this instruction booklet carefully, including its hints and warnings. To avoid unnecessary mistakes and accidents, it is important to ensure that all people using the dishwasher are thoroughly familiar with its operation and safety features. Save these instructions and make sure they remain with the dishwasher if it is moved or sold, so that everyone using it through its life can be properly informed on appliance use and safety.
Description of the appliance 1 Rinse conditioner dispenser 2 Spray arm 3 Coarse filter 4 Fine filter 5 Detergent dispenser 6 Salt container -4-
Rinse conditioner dispenser 1 Salt container 6 Use of a rinse conditioner will result in cleaner and faster drying of the load, since it helps water to run off. Too much conditioner may result in streakiness, too little may cause white spots. The dispenser holds about 140 ml. This is enough for 40-70 wash cycles, depending on the dosage setting. When the rinse conditioner level is approaching the bottom of the scale it is time to refill the dispenser.
The control panel Programme lamps 1 2 On/Off button Programme selection/ Delay start Cancel button button Programme selection/cancel button Control lamps: is used to: • select the programme • set the water softener • deactivate/activate the audible signal • cancel a dishwashing cycle Shows that: • Wash cycle in progress • Refilling of salt is necessary • Programme cycle ended Control lamps The programme cycle ended lamp has also other functions of visual signalling: • on the setting of the water sof
Adjusting the water softener To prevent limescaling on the dishes and to the interior of the dishwasher, the dishes must be washed with soft water. Contact your local Water Authority to find the exact water hardness level for your area. This dishwasher is equipped with a water softener, where tapwater which is harder than 4 °d (german degree) is softened. The water softener has 10 settings: Adjust the water softener according to the table below for the water hardness level for your area.
Loading the dishwasher How to load the dishes The illustration shows the dishwasher loaded with 5 place settings. Your own dishes are not likely to be identical to this load, but if you follow the advices below we are sure you will be pleased with the result. ● Always place glasses, cups and bowls upside down. ● Incline deep dishes (soup plates etc.) so that the water can run off when drying. ● Make sure that the dishes do not rest against each other.
Programme chart All types of dishes Type of dishes Plates and cooking pots Type of soil: • heavily soiled • normally soiled • dried-on food remnants especially eggwhite and starch • dried-on food remnants • normally soiled Coffee cups, delicate items • lightly soiled • lightly soiled Suitable programme: INTENSIVE 70° C Programmecycle: Washing 2 x rinses Final rinse Drying NORMAL 65° C Washing Rinse Final rinse Drying ENERGY SAVE 55° C 2) Washing Rinse Final rinse Drying GLASS 40° C QUICK 50°
Using the appliance Starting the programme Switching the dishwasher off / Unloading 1. Scrape or rinse off solid food remnants. Switch the dishwasher off when the audible signals for ended programme sounds (few short tones) or the lamp for the ended programme cycle lights up. 2. Load the dishwasher. (See the basket and loading). 3. Put the correct amount of detergent into the detergent dispenser. 1. Press the On/Off button. 2. Open the door and leave it slightly ajar. Wait approx.
In the event of a fault Before calling out an engineer, please check through the details below because some faults can be rectified easily without the need to call out an engineer. If an engineer is called to resolve a problem listed below or to repair a fault caused by incorrect installation or mis-use a charge will be made, even if the appliance is under guarantee. Fault Check The programme will not start.
In the event of a fault With help of the sound signals and flashing lamps on the panel, it’s possible that you can solve the problem yourself. When the problem is solved, press in the button for the disrupted programme and the programme continues. In the case of other fault messages: • Interrupt the dishwashing cycle. • Switch the dishwasher off. • Select the relevant programme again. If the problem occurs again, contact your local service centre, stating the fault message.
Information for test centres The salt container and rinse aid dispenser shall be filled in accordance with this instruction manual. Before conducting the measurements the dishwasher shall be operated for one or two complete cycles using detergent and a clean load.
Unpacking Damages If the dishwasher has been damaged during transport, you should immediately notify the company responsible for delivering it. Check that the dishwasher is undamaged. If you discover any damage, faults or that anything is missing, you should notify the dealer immediately. Never leave packaging material in a place where children may play with it.
Installation Positioning The dishwasher is intended to be installed on a kitchen drainer or worktop. To function properly, make sure that the appliance is level. Its height can be adjusted with the adjustable feets (8 mm each). Water inlet The temperature of the water supply should not exceed 65° C and the pressure should be between 50-1000 kPa (0,5 - 10 bar). It is important to have a tap or stopcock, positioned close to the dishwasher and with easy access.