Contents For the user For the installer Safety information 3 Description of the appliance 4-5 - Spray arm - Coarse strainer/microfilter - Fine filter - Detergent dispenser - Rinse aid dispenser - Water softener Technical specifications 14 Unpacking 15 - Damages - Use Installation The control panel 6 - Switching the buzzer off - Setting the delay start Adjusting the water softener 7 - Switching the rinse aid dispenser off Programme chart 8 Using the appliance 9 Rukowodstwo po \kspluata
Safety information Before installing and first using the dishwasher, read this instruction booklet carefully, including its hints and warnings. To avoid unnecessary mistakes and accidents, it is important to ensure that all people using the dishwasher are thoroughly familiar with its operation and safety features. Save these instructions and make sure they remain with the dishwasher if it is moved or sold, so that everyone using it through its life can be properly informed on appliance use and safety.
Description of the appliance 4 5 -4-
Description of the appliance Spray arm (1) 3. Wipe off any spillage carefully to prevent excessive foaming during the next wash programme. It is important to keep all the holes in the spray arm clear. A clogged hole can seriously affect washing efficiency. If the spray arm needs cleaning, unscrew the nut anticlockwise, remove the washer and lift off the spray arm. Clear the holes and shake out any food remnants. 4. Close the lid and press until it locks again.
The control panel Indicator lamps delayed start Controllamps A Water softener button On/Off button Buzzer button Delay start button Programme buttons Combination buttons ”A” In addition to selecting a programme, you can press these two buttons to adjust the setting of the water softener, switch off the buzzer and rinse aid dispenser.
Adjusting the water softener To prevent limescaling on the dishes and to the interior of the dishwasher, the dishes must be washed with soft i.e. water with low lime content. This dishwasher is equipped with a water softener, where tapwater which is harder then 4 °d (german degree) is descaled with special salt. Contact your local Water Authority to find the exact water hardness level for your area.
Programme chart All types of dishes Type of dishes Plates and cooking pots Type of soil: • heavily soiled • normaly soiled • dried-on food remnants especially eggwhite and starch • dried-on food remnants • normaly soiled Coffee cups, delicate items • lightly soiled • lightly soiled Suitable programme: INTENSIVE 70° C Programmecycle: 1) Pre-wash Washing 2 x rinses Final rinse Drying NORMAL 65° C Pre-rinse Washing Rinse Final rinse Drying ENERGY SAVE 55° C 3) Pre-rinse Washing Rinse Final rinse
Using the appliance Starting the programme Pause function 1. Scrape or rinse off solid food remnants. With the paus function the programme can be temporarily disrupted for a short period of time. 2. Load the dishwasher. (See the basket and loading). 1. Open the door and press the On/Off button. The programme stops. 3. Put the correct amount of detergent into the detergent dispenser and close the dispenser lid. 2. All lamps goes out. 4. Press in the On/Off button.
Loadind and unloading the dishwasher How to load the dishes Baskets The illustration shows the dishwasher loaded with six place settings. Your own dishes are not likely to be identical to this load, but if you follow the advice below we are sure you will be pleased with the results. Main basket Cutlery basket ● Always place glasses, cups and bowls upside down. ● Incline deep dishes (soup plates etc.) so that the water can run off when drying.
Maintenance and cleaning Cleaning the dishwasher Clean the outside surfaces of the appliance using a mild (non-abrasive) household cleaning product. Finish by removing remaining traces of the product with a damp cloth. Do not use cleaning products which contain alcohol (spirits), thinners and similar substances. Cleaning the filters The dishwasher has two filters, a coarse one and a fine one which should be inspected and cleaned, if necessary, after every wash.
In the event of a fault Before calling out an engineer, please check through the details below because some faults can be rectified easily without the need to call out an engineer. If an engineer is called to resolve a problem listed below or to repair a fault caused by incorrect installation or mis-use a charge will be made, even if the appliance is under guarantee. Fault Check The programme will not start.
Service Service and spare parts Servicing and repairs must be carried out by a service company authorized by the supplier. Use only spare parts supplied by these. Before calling service, use the trouble shooting table ”In the event of a fault” to try to attend to the fault yourself. Note that electrical faults shall always be rectified by a certified electrician. Give the appliance’s model designation, product- and serial numbers according to the data plate. You can record these details here: TYPE. .......
Installation instructions Any electrical work required to install this appliance, should be carried out by a qualified electrician or competent person. Any plumbing work required to install this appliance, should be carried out by a qualified plumber or competent person.
Unpacking Damages If the dishwasher has been damaged during transport, you should immediately notify the company responsible for delivering it. Check that the dishwasher is undamaged. If you discover any damage, faults or that anything is missing, you should notify the dealer immediately. 1 2 Never leave packaging material in a place where children may play with it.
Installation Position The machine is basically designed to be built into a cupboard. It is vital to ensure that the machine is positioned on a horizontal level in order for it to function properly and so that the door can be properly closed. Make sure that the shelf for the dishwasher is properly secured inside the cupboard. The cupboard must be secured properly onto the wall and the front edge of the shelf must be level with the sides of the cupboard.
Installation Preparing the outer door Screw the guide rods and hinges on the door into place using the predrilled holes. Mount plate 2x Before installing the dishwasher and adjusting the door onto the cupboard, put the mount plate into its correct position on the shelf. 1. Place the mount plate in the middle of the cupboard. Mark the holes for screws and the holes for dismounting the outer door. There is a middle mark on the plate to help you. 2. Drill 4 holes with a diameter of 7 mm.
Installation Mounting the outer door 1. Unscrew the screws on the mount plate. Lift the plate off together with the door. 2. Lay the machine down on its back. Check that none of the hoses are trapped. Insert the guide rods into the plastic door guides. 3. Slot the tabs on the mount plate into the holes on the front plinth of the machine and screw the mount plate into place using the 2 screws provided.
Installation Water inlet The dishwasher is equipped with safety features which are to prevent the water from going back to the fresh water system. These features are according to current water technical safety regulations. The temperature of the water supply should not exceed 65° C and the pressure should be between 80-1000 kPa (0,8 - 10 bar). It is important to have a tap or stopcock, positioned close to the dishwasher and with easy access.
- 39 -