T h e f u l l y i n t e g r a t a b l e d i s h w a s h e r Operating Instructions ESL 5391 153 137 013-A-230404-01 g
Dear Customer, Please read these user instructions carefully and keep them to refer to later. Please pass the user instructions on to any future owner of the appliance. The following symbols are used in the text: 1 Safety instructions Warning! Information that affects your personal safety. Important! Information that prevents damage to the appliance.
Contents Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Diagram of appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Control panel . . . . . . .
Operating Instructions 1 Safety Prior to using for the first time Risk of frost • Follow the ”Instructions for installation and connection”. • If the appliance is exposed to temperatures below freezing while connected, it must be correctly emptied by the Customer Service Centre. • When being delivered from the factory, there is no danger of the appliance freezing! Correct use • The dishwasher is only intended for washing domestic dishes. • Additions or modifications to the dishwasher are not permitted.
Diagram of appliance Ceiling spray arm Upper basket spray arm and floor spray arm Filters Dispenser for detergent Dispenser for rinse aid Control panel and programme overview Rating plate Dispenser for special salt Control panel ON/OFF button To use the appliance, always open the dishwasher door first. The ON/OFF button is used to turn the dishwasher on and off.
Function buttons Multi-display 1 2 3 Salt indicator Rinse aid indicator Delay timer Cycle selection button 3in1 function Half load Antibac The Programme selection button is used to select the desired dishwashing cycle.
Prior to using for the first time 1. Set the water softener 2. Fill up with special salt for water softeners 3. Fill up with rinse aid 3 If you wish to use 3in1 detergent, do the fol- lowing: – First read the section “Using 3in1 detergents”. – Switch on the dishwasher, press the 3in1 button . The button indicator lights up: 3in1 function is selected. As a result – there is no need to fill up with special salt or rinse aid. – there is no need to set the water softener.
Setting the water softener 3 To avoid scale deposits on the dishes and in the dishwasher, the dishes must be washed with soft water, i.e. water with a low lime content. The water softener must be set according to the table to the water hardness in the area where you live. Your local water company will be able to give you information about the water hardness in your area. 1. Press the ON/OFF button. 3 If indicators other than the cycle selection button are lit, a dishwashing cycle is activated.
Adding special salt To decalcify the water softener, it must be filled up with special salt. Use only special salt suitable for domestic dishwashers. If you do not use 3in1 detergent, fill up with special salt: – Before using the dishwasher for the first time. – When the control indicator for special salt is illuminated on the control panel. 1. Open the door and remove the lower basket. 2. Screw open the lid on the salt dispenser by turning it anti-clockwise. 3.
Filling up with rinse aid With rinse aid the rinsing water drains away better and so you get smear-free, gleaming dishes and clear glasses. If you do not use 3in1 detergent, fill up with rinse aid: – Before using the dishwasher for the first time. – When the control indicator for rinse aid is illuminated on the control panel. Use only special rinse aid for dishwashers and no other liquid detergents. 1. Open the door. The rinse aid compartment is located on the inside of the dishwasher door. 2.
Setting the amount of rinse aid required 3 Only change the amount dispensed, if smears, milky spots (reduce the amount) or dried on water spots (increase the amount) can be seen on glasses and dishes. (See section “If dishwashing results are not satisfactory”.) The dosage can be set from 1-6. The dosage is pre-set to “4” in the factory. 1. Open the dishwasher door. 2. Press the release button on the rinse aid compartment. 3. Open the cover. 4. Set the dosage level. 5.
Activating/deactivating the acoustic signal In addition to the optical display (e.g. indicating the end of the cycle, errors) you can also choose to set an acoustic signal. 1. Press the ON/OFF button. 3 If indicators other than the cycle selection button are lit, a dishwashing cycle is activated. The dishwashing cycle must be deselected: Press function buttons 2 and 3 simultaneously for approx. 2 seconds. All other indicators will go out. 2.
In daily use Loading cutlery and dishes 1 Sponges, cleaning cloths and any other objects that can absorb water must not be washed in the dishwasher. Plastic and Tefloncoated dishes and pans tend to retain water droplets. These dishes and pans therefore do not dry as well as those made of china and stainless steel.
Loading cutlery 1 Warning: Sharp knives and other items of cutlery with sharp edges must be laid in the cutlery rack or in the upper basket to avoid the risk of injury. To ensure that all items of cutlery in the cutlery basket can be reached by the water, the cutlery inserts should be inserted and where possible the cutlery placed handle downwards in the cutlery basket. 1 Exceptions to this are cutlery items with very narrow handles that could go through the cutlery basket and block the spray arm.
Pots, Pans, Large Plates Load large and heavily soiled dishes in the lower basket. The plate rack running right to left at the front righthand side is most suitable for small flat plates with a diameter of 170-210 mm. A serving plate can be placed in front of the cutlery basket. To make it easier to load larger dishes, all rear plate rests in the lower basket can be folded down. Folding down the right plate rest makes a second plate rest that is particularly suitable for deep plates or bowls. 1.
Cups, Glasses, Coffee Service Load smaller, fragile crockery and long, sharp cutlery in the upper basket. Adjustable cup racks • Arrange items of crockery on and under the folding cup racks so that they are offset from each other and water can reach all items. • The cup racks can be folded up out of the way for tall crockery items. • The cup racks can also be fixed in an intermediate position. Lay or hang glasses with stems in the slots in the cup racks.
Adjusting the height of the upper basket Maximum height of dishes in the Upper basket Lower basket with upper basket raised 19 cm 32 cm with upper basket lowered 21 cm 30 cm 3 The height of the baskets can also be adjusted when they are loaded. Raising/lowering the upper basket 1. Pull out the upper basket completely. 2. Raise the upper basket as far as it will go and then lower it vertically. The upper basket will latch into the lower or the upper position.
Adding detergent Detergents remove the dirt from dishes and cutlery. The detergent must be added before the cycle starts. 1 Only use detergent intended for domestic dishwashers. The detergent compartment is located on the inside of the door. 1. If the lid is closed: Press the release button. The lid will spring open. 2. Place the detergent in the detergent dispenser. The markings indicate the dosing levels for powder detergents: “20/30” corresponds to approx. 20/30 ml of detergent.
Concentrated detergents Today’s detergents for dishwashers are almost exclusively low-alkaline concentrated detergents with natural enzymes in tablet or powder form. 2 Using 50°C dishwashing cycles in conjunction with these concentrated detergents reduces pollution and is good for your dishes, as these dishwashing cycles are specially matched to the dirt-dissolving properties of the enzymes in concentrated detergents.
Used dishes that are being stored in the dishwasher to be washed later.
Starting a dishwashing cycle 1. Check that the spray arms can turn freely. 2. Turn the water tap on fully. 3. Press the ON/OFF button. The LED for the cycle selection button will illuminate. 4. Select the desired cycle. In addition, press the cycle selection button repeatedly until the desired cycle is displayed in the multi-display (see cycle table). 3 The cycle selected for the last dishwashing session is displayed first. 5. Close the door. The dishwashing cycle will begin.
Switching off the dishwasher If the acoustic signal has been enabled, a continuous tone will sound for approx. 15 seconds at the end of the dishwashing cycle. 1 Carefully open the door. Hot steam may escape. Hot dishes are sensitive to knocks. Therefore leave the dishes to cool for about 15 minutes before removing them. You also get a better drying result. 1. Press the ON/OFF button. All display indicators will go out. 2. Turn off the water tap.
Care and cleaning 1 Do not use furniture care products or aggressive cleaners. • When necessary, clean the dishwasher’s controls with a soft cloth and clean warm water. • Occasionally check the internal dispensers, door seal and water inlet filter (if fitted) for dirt and clean them, if necessary. Polished chromium steel surfaces Remove light dirt with a clean, damp, soft cloth – microfibre cloths are particularly good.
Fine filter (2) The fine filter must be cleaned occasionally. 1. Open the door and remove the lower basket. 2. Release the fine filter by turning to the right and remove. 3. Clean the fine filter thoroughly with a brush under running water. 4. Place the fine filter in the holder and turn to the left until you feel it click into place (arrow). 1 Do not press the handle downwards. If the filter does not click into place, this can lead to the spray arm nozzles becoming blocked.
Cleaning the spray arms Regularly check the nozzles in the three spray arms for blockages. If necessary, clean the nozzles with a piece of fine wire or a fine needle and a strong water jet. 1 Do not damage the nozzle openings. Top spray arm 1. Undo the fixing screw (A) by turning anti-clockwise. 2. Pull the spray arm off the shaft. 3. Clean the spray arm and the fixing screw. 4. Fasten the spray arm with the fixing screw (A) turning clockwise. Middle spray arm 1.
What to do if... Remedying small malfunctions If the acoustic signal is activated, warning tones sound if there are faults. If one of the following fault codes is displayed in the multi-display during operation: – Fault codeÅ 10 (Problems with water inlet), – Fault codeÅ 20 (Problems with water drainage), please have a look at the following table. When the fault is remedied, press the cycle selection button. The cycle will continue.
Malfunction Possible cause The mains plug is not plugged in. The cycle is not starting. Remedy Plug in mains plug. A fuse in the house’s wiring system Replace fuse. is defective. For dishwasher models with a delay If the dishes are to be washed imstart timer: mediately, cancel the delay start. A start time has been selected. Rust spots are visible in the dishwashing compartment. The dishwashing compartment is made from rust-free stainless steel.
If the dishwashing results are not satisfactory The dishes are still dirty. • The wrong dishwashing cycle was selected. • The dishes were loaded is such a way that the dishwashing water did not reach all items. The baskets for the dishes must not be overloaded. • The filters in the base of the washing compartment are dirty or incorrectly positioned. • Good quality detergent was not used, or too little was used.
Disposal 2 2 Packaging material The packaging materials are environmentally friendly and can be recycled. The plastic components are identified by markings, e.g. >PE<, >PS<, etc. Please dispose of the packaging materials in the appropriate container at the community waste disposal facilities. Old appliance Please dispose of your old appliance in line with the guidelines for disposal in your community. 1 Warning! When your appliance has finished its working life, remove the plug from the socket.
Notes for Test Institutes Testing in accordance with EN 60704 must be carried out with the appliance fully loaded and using the test cycle (see "Cycle Table"). Tests in accordance with EN 50242 must be carried out when the salt dispenser in the water softener and the rinse aid dispenser have been filled with salt and rinse aid respectively, and using the test cycle (see "Cycle Table"). Full load: 11 place settings incl. serving dishes Amount of detergent required: 27.
Installation and connection instructions Scope of use Dishwashing machines of type: 31 . . . General • The dishwasher is supplied ready to be connected to the electrical supply, i.e. with electrical cable, installed drain hose and inlet hose with filter. • The dishwasher may be built into recesses made of flammable materials without additional measures being taken. • It is preferable that the connection to the mains is located in the unit next to the dishwasher.
Connecting to the water supply 1 The appliance must be connected by specialist staff. Inlet • Water pressure: 1–10 bar (flow pressure) • The appliance can be connected to cold and hot water, maximum temperature 65 °C. • The site must provide a regulating tap with G 3/4” outlet. • The appliance must be connected with the plastic pressure hose supplied (with filter, in accordance with EN61770, 10 bar.) • Installation of an IRG filter is recommended as part of the house’s water system.
Installing and fitting the hinged door A normal kitchen unit door with the following dimensions can be used as a hinged door: • Max width 596 mm • Max. height 720 mm • Max. depth 20 mm • Weight (including handle) 3 kg to max. 8 kg 1 Do not exceed maximum door height, as oth- erwise the door will not be able to close properly. The hinged door must be fitted with a handle. The hinges needed for installation and the associated screws are standard parts and are not included in the delivery.
Fitting the hinged door 1. Fit the two lateral bars A as in the figure opposite. Use aligning disks B. 2. Stand the machine in front of the kitchen unit into which it is to be installed. Place cable and hoses into the neighbouring unit. As you push the machine in, keep on pulling the cable and hoses through and ensure that they do not become kinked. 3. Align the machine laterally in the plinth area with the angle AN, tighten the screw V slightly. 4.
5. Place the hinge supports on the floor of the recess and align, and screw on using 6 wood screws (flat head 4.5x16). 6. Using the drilling template supplied, mark out and drill two holes a (ø35 mm, 11 mm deep) for the hinges at the bottom of the hinged door. To do this, align the drilling template with the bottom edge of the hinged door.
7. Using the drilling template supplied, mark out and drill 8 holes b for the two guides (ø2 mm, 12 mm deep) at the top of the hinged door. To do this, align the drilling template with the top edge of the hinged door. 8. Screw the hinges (using 4 countersunk head wood screws, not supplied) and the guides (using 8 Spax screws 4.0x20, pozidrive) to the hinged door. 9. Snap the hinges on the hinged door into the bottom units of the hinges. Hold the hinged door carefully, so that the hinges are not bent. 10.
11.Insert the guiders into the guides. 12.Fix the guiders with screws to the right and the left on the appliance door. 13.Adjust the depth of the appliance, open the appliance door carefully, without changing the position found. Fix the appliance laterally with wood screws and the two disks D.
14.Fix the appliance laterally by tightening screw V. To do this, there are 2 oblong holes to the right and left in the hinge support to allow access for the screwdriver. Connection to the electrical supply 1 The appliance must only be connected to the electricity supply by a qualified electrician. • The machine is fitted with a 3 x 1 mm2 electrical cable with moulded plug (“Schuko”). • The appliance must be connected to a mains cable designed for the rated output.
Service The section “What to do if...” summarizes the main error sources that you can rectify yourself. If, nevertheless, you request a visit from customer service to remedy a problem listed in these instructions, or because of an error made in operating the appliance, a visit from a customer service engineer is not free of charge, even during the warranty period. If you cannot find information on a specific malfunction in these operating instructions, please contact customer service.
153 137 013-A-230404-01 Subject to change without notice The Electrolux Group. The world´s No.1 choice. The Electrolux Group is the world´s largest producer of powered appliances for kitchen, cleaning and outdoor use. More than 55 million Electrolux Group products (such as refrigerators, cookers, washing machines, vacuum cleaners, chain saws and lawn mowers) are sold each year to a value of approx. USD 14 billion in more than 150 countries around the world.
