Installation Guide

30" DUAL FUEL SLIDE-IN RANGE INSTALLATION INSTRUCTIONS
(Models with an Electric Oven and a Gas Cooktop)
11
7
LP/Propane Gas Conversion
This appliance can be used with Natural gas or LP/
Propane gas. It is shipped from the factory for use with
natural gas.
If you wish to convert your range for use with LP/
Propane gas, use the supplied xed orices located
in a bag containing the literature marked "FOR
LP/PROPANE GAS CONVERSION." Follow the
instructions packaged with the orices.
The conversion must be performed by a qualied
service technician in accordance with the
manufacturer's instructions and all local codes and
requirements. Failure to follow these instructions
could result in serious injury or property damage.
The qualied agency performing this work assumes
responsibility for the conversion.
Failure to make the appropriate
conversion can result in personal injury and property
damage.
8
Moving the Appliance for
Servicing and Cleaning
Turn off the range line fuse or circuit breakers at
the main power source, and turn off the manual gas
shut-off valve. Make sure the range is cold. Remove
the service drawer (warmer drawer on some models)
and open the oven door. Lift the range at the front
and slide it out of the cut-out opening without creating
undue strain on the exible gas conduit. Make sure
not to pinch the exible gas conduit at the back of the
range when replacing the unit into the cut-out opening.
Replace the drawer, close the door and switch on the
electrical power and gas to the range.
9.
Range Installation
Important Note: Door removal is not a requirement for
installation of the range, but is an added convenience.
9.1
The range cooktop overlaps the countertop at
the sides and the range rests on the oor. The
cooktop is 31 1/2" (80 cm) wide.
9.2
Install base cabinets 30" (76,2 cm) apart. Make
sure they are plumb and level before attaching
cooktop. Shave raised countertop edge to clear
31 1/2" (80 cm) wide range top rim.
9.3
Install cabinet doors 32" (81,3 cm) min. apart so it
will not interfere with range door opening.
9.4
Cutout countertop exactly as shown on page 4.
For models equipped with Leveling Device:
9.5
Make sure the front leveling legs and the rear
leveling device are setup higher than the height
of the cabinet.
9.6
Remove and discard the two rear leveling legs,
they are only in place to solidify the unit for the
transport.
9.7
Install the anti-tip bracket at
this point before placing the range at its nal
position. Follow the installation instructions
on page 14 or on the anti-tip bracket template
supplied with the range.
9.8
To provide an optimum installation, the top
surface of the countertop must be level and
at (lie on the same plane) around the 3 sides
that are adjacent to range cooktop. Proper
adjustments to make the top at should be made
or gaps between the countertop and the range
cooktop may occur.
9.9
To reduce the risk of damaging
your appliance, do not handle or manipulate it by the
cooktop or control console. Manipulate with care.
9.10
Position range in front of the cabinet opening.
9.11
Make sure that the cooktop which overhangs the
countertop clears the countertop. If necessary,
raise the unit by lowering the leveling legs.
9.12
Slide the range into the cutout opening and
center it before leveling it.
9.13
Level the range (see section 9). The oor where
the range is to be installed must be level. Follow
the instructions under "Leveling the Range-
Models Equipped with Leveling Device".
9.14
Adjust leveling legs so that the underside of the
cooktop is sitting on the countertop. Carefully
screw in (refer to Leveling the range: Models
equipped with Leveling Device") the back leveling
leg until the cooktop overhang touches slightly
the countertop. Then carefully screw in the front
two leveling legs until the cooktop overhang
touches slightly the countertop.
Refer to the Use
and Care Guide for
oven door removal
instructions.
Figure 12