Installation Instructions 30” Free-Standing Electric Range Instrucciones de Instalacion Estufa Electrica de 30" 316454909
station
INSTALLATION INSTRUCTIONS FOR FREESTANDING ELECTRIC RANGE INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER. IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE. READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. Clearances and Dimensions 1. Provide adequate clearances between the range and adjacent combustible surfaces. 2. Location—Check location where the range will be installed. Check for proper electrical supply, and the stability of the floor. 3.
INSTALLATION INSTRUCTIONS FOR FREESTANDING ELECTRIC RANGE BEFORE STARTING Tools You Will Need For leveling legs and Anti-Tip Bracket: 3/16" pilot hole 1-3/4" deep. The screws provided may be used in wood or concrete material. Use a 5/16" nut-driver or flat head screwdriver to secure the bracket in place (See Fig. 6). 1c. Level and Position Range - Level range by adjusting the (4) leveling legs with a wrench.
INSTALLATION INSTRUCTIONS FOR FREESTANDING ELECTRIC RANGE 2b. MODELS REQUIRING POWER SUPPLY CORD KIT. RISK OF FIRE OR ELECTRICAL SHOCK MAY OCCUR IF AN INCORRECT SIZE RANGE CORD KIT IS USED, THE INSTALLATION INSTRUCTIONS ARE NOT FOLLOWED OR STRAIN RELIEF BRACKET IS DISCARDED. This appliance may be connected by means of a power supply cord. Only a power supply cord kit rated at 125/250 volts minimum, and marked for use with ranges shall be used. See Fig. 10 for cord kit ampere rating information.
INSTALLATION INSTRUCTIONS FOR FREESTANDING ELECTRIC RANGE or 4B. POWER CORD CONNECTIONS (3-Wire Connection Instructions . For existing installations ONLY - Refer to Fig. 13). 1. 2. 3. Follow the manufacturer’s installation instructions supplied with the strain relief and install (Also see Figs. 9, 10 & 11). Insert the end connectors for Line 1, Line 2 and Neutral and tighten securely to the terminal block (See Fig. 13).
INSTRUCCIONES DE INSTALACION PARA LA ESTUFA ELECTRICA DE 30" LA INSTALACION Y EL SERVICIO DEBEN SER EFECTUADOS POR UN INSTALADOR CALIFICADO. IMPORTANTE: CONSERVE ESTAS INSTRUCCIONES PARA USO DEL INSPECTOR LOCAL DE ELECTRICIDAD. LEA Y CONSERVE ESTAS INSTRUCCIONES PARA REFERENCIA FUTURA. Espacios Libres y Dimensiones 1. Provea espacios libres adecuados entre la estufa y las superficies combustibles adyacentes. 2. Ubicación – Revise el lugar donde será instalada la estufa.
INSTRUCCIONES DE INSTALACION PARA LA ESTUFA ELECTRICA DE 30" ANTES DE COMENZAR 1b. Taladre agujeros pilotos e instale el soporte - Taladre un Herramientas Necesarias Para los tornillos niveladores y soporte antivuelco: agujero piloto de 1/8" donde se vayan a instalar los tornillos. Si el soporte va a ser instalado en la pared, taladre un agujero piloto en un ángulo descente de aproximadamente 20° (Ver Fig. 5).
INSTRUCCIONES DE INSTALACION PARA LA ESTUFA ELECTRICA DE 30" Consulte la Tabla del Tamaño de la Abertura de Conexión de la Estufa (Figs. 9 y 10) para la información sobre los amperes del juego de cordón. Los bornes en los extremos de los almabres deben ser de anillo cerrado u horquillas abiertas con extremos dirigidos hacia arriba. Sujetacable 2b.
INSTRUCCIONES DE INSTALACION PARA LA ESTUFA ELECTRICA DE 30" o 4B. CONEXIONES DEL CORDON DE ALIMENTACION Instrucciones para conexión trifilar (para instalaciones existentes SOLAMENTE Consulte la Fig. 13). Conexión Trifilar 1. Siga las instrucciones de instalación del fabricante suministradas con el sujetacable e instale (Además vea las Figs. 9, 10 y 11). 2. Inserte los conectores de extremo para la Línea 1, Línea 2 y Neutro y apriete firmemente en el tablero de bornes.
station