EWF12822 ................................................... ........................................................
www.electrolux.com CONTENTS 1 2 3 4 5 6 7 8 9 10 11 12 SAFETY INFORMATION .............................................................................................. 3 PRODUCT DESCRIPTION ........................................................................................... 5 CONTROL PANEL ...................................................................................................... 6 BEFORE FIRST USE ......................................................................................
ENGLISH 1. 3 SAFETY INFORMATION Conditions of use This appliance is intended to be used in household and similar applications such as: - Farm houses - By clients in serviced apartments, holiday apartments and residential type environments. In the interest of your safety and to ensure the correct use, before installing and first using the appliance, read this user manual carefully, including its hints and warnings.
www.electrolux.com After having installed the appliance, check that it is not standing on the inlet and drain hose and the worktop is not pressing the electrical supply cable. If the machine is situated on a carpeted floor, please adjust the feet in order to allow air to circulate freely. Always be sure, that there is no water leakage from hoses and their connections after the installation. Any plumbing work required to install this appliance should be carried out by a qualified plumber.
ENGLISH 5 2. PRODUCT DESCRIPTION 1 7 3 2 9 11 4 8 5 10 12 6 7 Mains Cable 1 Worktop 2 Detergent/Softener Dispenser 8 Water Inlet Hose 9 Water Drain Hose 3 Control Panel 4 Door Handle 10 Hose Support 5 Door 6 Level Adjustment Feet (Front) 11 Transit Bolts 12 Level Adjustment Feet (Back) ACCESSORIES Plastic caps 14 13 13 Child Safety Device 14 Rating Plate 15 15 Drain Pump Filter To close the holes on the rear side of the cabinet after the removal of the transit bolts.
www.electrolux.com 3. CONTROL PANEL 2 5 4 1 3 8 6 9 10 11 12 7 14 13 1 On/off Button 2 Program Knob 8 Display 9 Rinse Plus Touchpad 3 Favourite Touchpad 4 Temperature Touchpad 10 Prewash Touchpad 11 Easy Iron Touchpad 5 Spin Selection Touchpad 6 Adjust Time Touchpad 12 Vapour Touchpad 13 Start/Pause Touchpad 7 Delay Start Touchpad 14 Child Lock Option (See Page 17) 3.1 On/off Button On/Off button is used to turn On and turn Off your washing machine. 3.
ENGLISH To re-program Favourite with your own selections and save them, proceed as follows: 1. Put machine in PAUSE mode. 2. Touch the Favourite button to enter re-programming mode. Confirmmation of entering the re-programming mode shows on the screen. 3. Select your desired wash settings. 4. To EXIT re-programming mode without saving changes, touch ‘Start/Pause’ touchpad. 5. To save new program, touch ‘Favourite’ once. 3.
www.electrolux.com If you wish to add laundry in the machine during the delay time press Start/Pause touchpad to put the machine in pause mode. Add laundry, close the door and press Start/Pause touchpad again. You can cancel the delay time at any moment, by pressing ‘Delay Start’ touchpad repeatedly till the display shows delay time ‘ ’, then press the Start/Pause touchpad. 3.
ENGLISH 3.11 Easy Iron Touchpad When selecting this option the laundry is gently washed and spun to avoid creasing. In this way ironing is easier. The indicator of this option comes on. 3.12 Vapour Touchpad Select this option to add approximately 15-40 minutes of tumbling in vapour during the wash cycle. Vapour helps open fabric fibers up to allow laundry additives to release tough stains. The indicator of this option comes on.
www.electrolux.com 3.15 Programs + Options Program; Type of load; Temperature Max. weight of load Cottons; 90 °C to (Cold water) White and coloured cotton with heavy level of soil; max. load 8.5 kg. Cycle Options can be description combined - Wash - Rinses - Long spin Spin Reduction - 1200 to 400 rpm - No Spin - Rinse Hold - Extra Silent Prewash, Easy Iron, Rinse +, Vapour 1) , Adjust Time, Delay Start Mixed; 60 °C to (Cold water) Synthetic or mixed fabric items with normal level of soil; max.
ENGLISH Type of load; Program; Temperature Max. weight of load Cycle description Options can be combined Machine washable wool, hand washable woollen Hand Wash; and delicate fabrics with 40 °C to hand washing ‘ ’ (Cold water) care symbol; max. load 2 kg.
www.electrolux.com 4. BEFORE FIRST USE 1. Ensure that the electrical and water connections comply with the installation instructions. 2. Put 2 litres of water in the detergent compartment for washing phase. This activates the drain system. 3. Select a Cottons cycle at 90 °C, without any laundry in the machine, to remove any manufacturing residue from the drum and tub. Pour 1/2 a measure of detergent into the dispenser drawer and start the machine. 5.
ENGLISH 13 3. If you want your laundry to be spun or use temperature different from the one proposed by the washing machine, When these touchpads are pressed, the corresponding pilot lights come on. When they are pressed again, the pilot lights go out. pess the Spin ‘ ’ and the temperature ‘ ’ touchpads repeatedly to change the spin speed and temperature. 5. If you want to reduce washing time, press the ‘Adjust Time ’ touchpad repeatedly to reduce washing time. 4.
www.electrolux.com 4. Make sure that no laundry remains between the seal and the door. 5. Close the door. Step 3 - Using Detergent And Additives 1. Detergent Dispenser Drawer Powder or liquid detergent. 1 2 The detergent dispenser is divided into three compartments. - Detergent flap Flap for powder or liquid detergent. - Compartment ‘MAIN WASH’ This compartment is used for detergent on all programs.
ENGLISH - Do not put more liquid than the maximum level. - Do not set the PREWASH phase. - Do not set the DELAY START. 2. Measure out the detergent and the fabric softener; 15 - If you wish to carry out the “Prewash” phase, pour it into the compartment marked . - If required, pour fabric softener into the compartment marked (the amount used must not exceed the “MAX” mark in the drawer). - Pull out the dispenser drawer until it stops.
www.electrolux.com 5.2 Interruption Of A Program - To pause press Start/ Pause. The indicator will start flashing. - Press the Start/Pause again. The program will continue. If you can not open the door but you need to open it you have to switch the machine off by pressing the ‘On/Off’ button to deactivate the appliance. After about 5 minutes the door can be opened. 5.3 Changing A Program CAUTION! Pay attention to the water level and water temperature.
ENGLISH 4. When the program is completed and the door lock indicator ‘ ’ goes off, you can open the door. 5. Press the ‘On/Off’ button to deactivate the appliance. 5.8 AUTO Stand-by Option The AUTO Stand-by option automatically deactivates the appliance to decrease the energy consumption when: You do not press any buttons for 5 minutes before you press “Start/Pause”. Press the “On/Off” button to activate the appliance again. After 5 minutes from the end of the washing program.
www.electrolux.com 6. WASHING HINTS 6.1 Sorting The Laundry Follow the wash code symbols on each garment label and the manufacturer’s washing instructions. Sort the laundry as follows: whites, coloureds, synthetics, delicates, woollens. 6.2 Temperatures For normally soiled white cottons and linen 90°C (e.g. teacloths, towels, tablecloths, sheets...). For normally soiled, colourfast garments (e.g. 60°C shirts, night dresses, 50°C pyjamas....
ENGLISH Rust: oxalic acid dissolved in hot water or a rust removing product used in cold water. Be careful with rust stains which are not recent since the cellulose structure will already have been damaged and the fabric tends to hole. Mould stains: treat with bleach, rinse well (whites and fast coloureds only). Grass: soap lightly and treat with bleach (whites and fast coloureds only). Ball point pen and glue: moisten with acetone (*), lay the garment on a soft cloth and dab the stain.
www.electrolux.com Any fabric softener or starching additives must be poured into the compartment marked ‘ ’ before starting the wash program. Follow the product manufacturer’s recommendations on quantities to use and do not exceed the MAX mark in the detergent dispenser drawer. Do not spray stain pre-treatment products (e.g. Preen) on or near the machine, as it can attack plastic materials reducing its life. 6.
ENGLISH 7. INTERNATIONAL WASH CODE SYMBOLS These symbols appear on fabric labels, in order to help you choose the best way to treat your laundry. Energetic wash Max. wash Max. wash temperature temperature 95 °C 60 °C Max. wash temperature 40 °C Max. wash temperature 30 °C DO NOT wash at all Hand wash Delicate wash Bleaching Bleach in cold water Ironing Hot iron max. 200 °C Dry cleaning Dry cleaning in all solvents DO NOT bleach Warm iron max. 150 °C Lukewarm iron max.
www.electrolux.com 8. CARE AND CLEANING WARNING! You must DISCONNECT the appliance from the electricity supply, before you can carry out any cleaning or maintenance work. 8.1 External Cleaning Clean the appliance only with soap and warm water. Fully dry all the surfaces. CAUTION! Do not use alcohol, solvents or chemical products. 8.2 Descaling The water we use normally contains lime. It is a good idea to periodically use a water softening powder in the machine.
ENGLISH 23 To aid cleaning, the top part of the additive compartment should be removed. 8.6 Cleaning The Drawer Recess Having removed the drawer, use a small brush to clean the recess, ensuring that all washing powder residue is removed from the upper and lower part of the recess. Replace the drawer and run the rinse program without any clothes in the drum. 8.7 Cleaning The Pump Regularly examine the drain pump and make sure that it is clean. Clean the pump if: The appliance does not drain the water.
www.electrolux.com To clean the drain pump: 1. Open the drain pump door. 2. Pull the flap down. 3. Put a container below the recess of the drain pump to collect the water that flows out. 4. Press the two levers and pull forward the drainage duct to let the water flow out. 5. When the container is full of water, put the drainage duct back again and empty the container. Do steps 4 and 5 again and again until no more water flows out from the drain pump.
ENGLISH 6. Pull back the drainage duct and turn the filter to remove it. 1 2 7. Remove fluff and objects from the pump (if there are any). 8. Make sure that the impeller of the pump can turn. If this does not occur, contact the service centre. 9. Clean the filter under the water tap.
www.electrolux.com 10. Put the filter back in the pump into the special guides. Make sure that you tighten correctly the filter to prevent leakages. 11. Put the flap back and close the drain pump door. 8.8 Cleaning The Water Inlet Filter If your water is very hard or contains traces of lime deposit, the water inlet filter may become clogged. It is therefore a good idea to clean it from time to time. To clean the water inlet filters: 1. Close the water tap. 2.
ENGLISH 45° 8.9 The Dangers Of Freezing If the machine is exposed to temperatures below 0°C, certain precautions should be taken. Disconnect the mains plug from the mains socket. 1. Turn off the water tap. 2. Unscrew the inlet hose. 3. Put a bowl below the recess of the drain pump to collect the water that flows out. 27 6. Install again the inlet hose. Make sure that the couplings are tight to prevent leakages. 7. Open the water tap. 4.
www.electrolux.com 9. TROUBLESHOOTING Certain problems are due to lack of simple maintenance or oversights, which can be solved easily without calling out an engineer. Before contacting your local Service Centre, please carry out the checks listed below. During machine operation it is possible that the red Start/Pause pilot light flashes to indicate that the machine is not working. Once the problem has been eliminated, press the Start/Pause button to restart the program.
ENGLISH Malfunction There is water on the floor: Unsatisfactory washing results: The door will not open: The machine vibrates or is noisy: Cycle time longer than displayed: Possible cause 29 Solution Too much detergent or unsuitable detergent (creates too much foam) has been used. Reduce the detergent quantity or use another one. Check whether there are any leaks from one of the inlet hose fittings. It is not always easy to see this as the water runs down the hose; check to see if it is damp.
www.electrolux.com Malfunction Possible cause The electronic unbalance detection device has cut in because the laundry is not evenly distributed in the drum. Spinning starts late or the machine does not spin: The machine makes an unusual noise: No water is visible in the drum: Solution Pause the machine and redistribute laundry manually. The laundry is redistributed by reverse rotation of the drum. This may happen several times before the unbalance disappears and normal spinning can resume.
ENGLISH 31 10. TECHNICAL DATA Dimensions (Width / Height / Depth) Power supply (Voltage / Frequency) 59.6 X 84.8 X 66.5 cm 220-240 V / 50 Hz Total power absorbed 2200 W Minimum fuse protection Water supply pressure (Maximum / Minimum) Maximum load Spin speed (Maximum / Minimum) 10 A 0.8 MPa / 0.05 MPa Cottons Mixed Delicates Quick 18 Rinse Spin Energy Server Hand Wash Bedding Wool Refresh Cottons Refresh Mixed 8.5 Kg 4 Kg 4 Kg 1.5 Kg 8.5 Kg 8.5 Kg 8.5 Kg 2 Kg 3 Kg 2 Kg 1.5 Kg 1.
www.electrolux.com 11 .INSTALLATION 11.1 Unpacking CAUTION! All transit bolts and packing must be removed before using the appliance. You are advised to keep all transit devices so that they can be refitted if the machine ever has to be transported again. 1. Use gloves. Remove the external film. If necessary, use a cutter. 2. Remove the cardboard top. 3. Remove the polystyrene packaging materials. 4. Remove the plastic bag which cover the machine. 5. Open the door.
ENGLISH 6. Put one of the polystyrene packaging elements on the floor behind the appliance. Carefully put down the appliance with the rear side on it. Make sure not to damage the hoses. 7. Remove the polystyrene base. 8. Pull up the appliance in vertical position. 1 2 9. Remove the power supply cable and the drain and inlet hoses from the hose holders (A) on the rear of the appliance. A 10. Remove the three bolts. Use the key supplied with the appliance. 11. Pull out the plastic spacers.
www.electrolux.com 1 12. Put the plastic caps in the holes. You can find these caps in the user manual bag. 2 3 11.2 Positioning It is important that your washing machine stands firm and level on the floor to ensure correct operation. That the appliance must not be installed behind a lockable door, a sliding door or a door with a hinge on the opposite side to that of the washing machine door is restricted. Use a spirit level on the top and side of the washing machine to check the levels.
ENGLISH 35 Install the machine on a flat hard floor. Make sure that air circulation around the machine is not impeded by carpets, rugs etc. Check that the machine does not touch the wall or cupboard units. 11.3 Water Inlet Connect the water inlet hose to a tap with 3/4” BSP thread. Use the hose supplied with the washing machine. DO NOT USE OLD HOSES. The other end of the inlet hose which connects to the machine can be turned in any direction.
www.electrolux.com 11.5 Electrical Connection This machine is designed to operate on a 220-240 V, single-phase, 50 Hz supply. “An incorrect power supply may void your warranty.” Check that your domestic electrical installation can take the maximum load required (2.2 kW), also taking into account any other appliances in use. CAUTION! Connect the machine to an earthed socket outlet.
ENGLISH 37 12. ENVIRONMENT CONCERNS 12.1 Packaging Materials The materials marked with the symbol are recyclable. >PE<=polyethylene >PS<=polystyrene >PP<=polypropylene This means that they can be recycled by disposing of them properly in appropriate collection containers. 12.2 Old Machine Use authorised disposal sites for your old appliance. Help to keep your country tidy! The symbol on the product or on its packaging indicates that this product may not be treated as household waste.
www.electrolux.
807209702-E-142013 www.electrolux.
