User manual

Troubleshooting
When the following problems occur, the microcomputer will detect the
abnormal condition and an electronic buzzer sounds for approximaly 10
seconds and the indicatos flash as show.
Check the Power On/Off button.
Check the Start/Pause button.
Check whether under Delay start condition.
Check the power cord whether is securely plugged in.
Check whether power failure occurs.
Check whether the fuse or circuit breaker has been activated..
The washer
does not
work.
Water does
not flow into
tub or water
flow is slim.
Turn on the water supply faucet.
Check whether water supply has been cut off.
Check whether the metal filter in water inlet is clogged.
Check whether washer has been freezing.
Check whether water pressure is to low.
The heigh of drain hose is less than 700mm.
PROBLEM
WHERE TO CHECK
39 electrolux troubleshooting
The height of drain hose is more than 1000mm.
Put down the drain hose from the hookhole.
Check the drain hose for any obstructions.
Check whether the drain hose is clogged.
Check whether the drain rises too high of the ground.
Water does
not drain out.
The washer
does not
spin.
Check whether the laundry is clumped on one side of the tub.
Check whether the washer is on the level surface.
Close the washer lid.
ENG
DISPLAY
Check whether the washer is under Child lock.
Check whether the wash lid is open.
Press the Power On/Off button to turn off the power.
Call the service centre for technical assistance.
The trouble indicators can be released by pressing the Start/Pause button once if you want to
release the emergency stop. Then press Start/Pause button againt ot restart the operation.
No trouble conditions
During Washing or Rinsing, water continues to flow into machine. This is possibly
automatic water adding due to water level decrease.
Spin tub turns or stops timely at the beginning of spinning. This is intermittent
spinning for better spin effect.
Water inletting and rinsing sometimes during spinning. This is automatic lean-
correction due to clothes is not balanced.
There is sound like water flow after spinning. This is thesound of balance liquid in
balance ring. It is for reducing vibrations of spinning.
Control panel keeps warm after power off, this is caused by remembering circuitry
working.
Power off during working and the washer could not continue working. Should set
the program again
Does not
wash.
Other
troubles.
E1
E2
E3
E4
E5
EA
EC
ESP
precauciones de seguridad electrolux 04
Seguridad electrica
Los alambres de este cable eléctrico
están coloreados según el siguiente
código:
Verde/amarillo: tierra
Celeste: neutral
Marrón: vivo
Mientras que los colores de alambres
en los cables eléctricos de la máquina
no correspondan con la calificación de
color que identifican los polos en su
enchufe, proceda así:
El cable de color verde y amarillo debe
conectarse al terminal en el
tomacorriente que está marcado con
una E o con el símbolo de tierra o de
color verde o de color verde y amarillo.
El cable celeste debe conectarse al
terminal que está marcado con la letra
N o de color blanco.
El cable marrón debe conectarse al
terminal que está marcado con la letra
L o de color negro.
Cable a tierra
Si el tomacorriente de salida para tres
patas tiene terminal a tierra, enganche
seguramente el final del cable a tierra al
terminal.
Cuando esté en tierra la lavadora,
conecte el cable a tierra antes de
enchufar el cable de poder.
Si el tomacorriente de salida para tres
patas no tiene terminal a tierra,
consulte a su distribuidor más cercano
o de forma segura, conecte el final del
cable a tierra en un punto a tierra
adecuado como una tubería de agua
fría de metal. Nunca conecte el cable a
tierra con una tubería de gas.
Desenchufe el cable eléctrico antes de
desconectar el cable a tierra.
Cable a tierra
Varilla de
puesta a tierra