User manual
27
Telecomando
suggerimenti e informazioni
• In fase di sostituzione delle batterie, non
usarne di vecchie e non mescolare batterie
di tipo diverso. Ciò potrebbe provocare dei
problemi di funzionamento al telecomando.
• Nel caso in cui il telecomando non venga
usato a lungo, estrarre le batterie, dato
che quelle vecchie potrebbero perdere o
corrodersi danneggiando il telecomando.
• La normale durata delle batterie con impiego
normale è di circa sei mesi.
• Nel caso in cui il telecomando non funzioni
normalmente, estrarre e inserire nuovamente
le batterie. Nel caso in cui il comportamento
anomalo continui, sostituire con batterie
nuove.
8m
• Mantenere il telecomando a una distanza tale
da potere raggiungere il ricevitore sull’unità
interna (distanza massima 8 m).
• Se si seleziona il funzionamento con il timer,
il telecomando trasmette automaticamente
all'unitàinternailsegnaleall’oraspecicata.
• Il condizionatore non funziona se tende, porte
o altri oggetti ostruiscono la ricezione dei
segnali del telecomando da parte dell’unità
interna.
• Evitare di versare liquidi sul telecomando. Non
esporre il telecomando alla luce diretta del sole
o a fonti di calore.
• Se il ricevitore dei segnali infrarossi sull’unità
interna è esposto alla luce diretta del
sole, il condizionatore può non funzionare
correttamente. Usare delle tende per evitare
che la luce solare diretta colpisca il ricevitore.
• Se altre apparecchiature elettriche rispondono
al telecomando, spostarle oppure consultare il
rivenditore locale.
Displayunitàinterna
• Se si tiene il telecomando in una posizione che
impedisce la corretta trasmissione del segnale,
possono passare anche 15 minuti prima che il
segnale sia ricevuto.
• Quando il telecomando lancia un segnale, il
simbolo
lampeggia per circa 1 secondo sul
display. L'unità interna conferma la ricezione del
segnale con un bip quando riceve un segnale.
attenzione
Comeusareiltelecomando
• Puntare il telecomando sul ricevitore del segnale
dell'unità interna.
• Vericarechenonvisianoostacoliche
potrebbero interferire col segnale.
Posizionedeltelecomando
Installazione/sostituzionedellabatteria
• Togliere il coperchio dell'alloggiamento delle
batterie e inserire due nuove batterie alcaline
secche(2xAAA1,5volt).Vericarechela
polarità (+) o (-) sia stata rispettata.
• Riposizionare il coperchio
IndicatoreModalitàRiscaldamento
Si accende quando è attivata la funzione
riscaldamento
IndicatoreModalitàRaffreddamento
Si accende quando è attivata la funzione
raffreddamento
IndicatoreAlimentazioneON/OFF
Si accende quando l’apparecchiatura è in
funzione o in modalità standby
IndicatoreDeumidicazione
Si accende quando è attivata la funzione
deumidicazione
Indicatoredellatemperatura
Visualizza la temperatura impostata quando il
condizionatore è in funzione
Ricevitoredisegnale
7
RemoteControl
tips and information
• When changing batteries, do not use old
or varied ones, otherwise, it may cause
problems with the remote control.
• If the remote control is not used for a long
time, remove the batteries as old batteries
may leak or corrode and damage the remote
control.
• The battery life during normal use is about six
months.
• If the remote control does not operate
normally,pleaseremoveandretthe
batteries. If abnormal operation continues,
replace with new batteries.
8m
• Keep the remote control where its signal
can reach the receiver of the indoor unit (a
maximum distance of 8m is allowed).
• When you select the timer operation, the
remote control automatically transmits a signal
totheindoorunitatthespeciedtime.
• The air conditioner will not operate if curtains,
doors or other materials block the signals from
the remote control to the indoor unit.
• Prevent any liquid from falling into the remote
control. Do not expose the remote control to
direct sunlight or heat.
• If the infrared signal receiver on the indoor
unit is exposed to direct sunlight, the air
conditioner may not function properly. Use
curtains to prevent the sunlight from falling on
the receiver.
• If other electrical appliances react to the
remote control, either move these appliances
or consult your local dealer.
IndoorUnitDisplay
Signal
receiver
• If you keep the remote control in a position that
hinders proper signal transmission, a time lag of
up to 15 minutes may occur.
• When the remote control sends out a signal, the
symbol
will blink for about 1 second on the
display. The indoor unit will acknowledge the
signal with a beep when it receives an effective
signal.
IFeelindicator
It lights when I Feel function is activated.
Turboindicator
Illuminates during Turbo operation.
Eco(Economy)indicator
Illuminates when ECO function is in operation.
Temperatureindicator
Displays the temperature settings when the air
conditioner is in operation.
Timerindicator
The indicator illuminates when Timer is set ON
and/or OFF.
Swingindicator
It lights when the Swing function is activated.
caution
HowtousetheRemoteControl
• Point the remote control to the signal receiver of
indoor unit.
• Make sure there is no obstacle that may interfere
with the signal.
Locationoftheremotecontrol
Batteryinstallation/replacement
• Slide the battery compartment cover off and
insert two new alkaline dry batteries
(2x AAA1.5Volt). Make sure that the polarity of
(+) or (-) is installed correctly.
• Slide the battery compartment cover back on
Light
Turbo
Timer-On
Temp
Timer-Off
Swing
I feel
Eco
Fan
Clock
Mode