GA55GLV EN DE Dishwasher Geschirrspüler User Manual Benutzerinformation 2 26
www.electrolux.com CONTENTS 1. SAFETY INFORMATION....................................................................................3 2. SAFETY INSTRUCTIONS..................................................................................4 3. PRODUCT DESCRIPTION................................................................................ 6 4. CONTROL PANEL............................................................................................. 7 5. PROGRAMMES.....................................
ENGLISH 1. 3 SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference. 1.
www.electrolux.com • • • • • • • • • The operating water pressure (minimum and maximum) must be between 0.5 (0.05) / 8 (0.8) bar (MPa) Obey the maximum number of 12 place settings. If the supply cord is damaged, it must be replaced by the manufacturer, its Authorised Service Centre or similarly qualified persons in order to avoid a hazard. Put the cutlery in the cutlery basket with the sharp ends pointing down or put them in the cutlery drawer in a horizontal position with the sharp edges down.
ENGLISH • • • • Connect the mains plug to the mains socket only at the end of the installation. Make sure that there is access to the mains plug after the installation. Do not pull the mains cable to disconnect the appliance. Always pull the mains plug. This appliance complies with the E.E.C. Directives. UK and Ireland only. This appliance is fitted with a 13 A mains plug. If it is necessary to change the mains plug fuse, use only a 13 A ASTA (BS 1362) fuse. 2.
www.electrolux.com 3. PRODUCT DESCRIPTION 1 2 11 10 1 2 3 4 5 6 9 8 7 Upper spray arm Lower spray arm Filters Rating plate Salt container Air vent 4 6 5 7 8 9 10 11 Rinse aid dispenser Detergent dispenser Cutlery basket Lower basket Upper basket 3 3.1 TimeBeam TimeBeam displays the following information on the floor below the appliance door: • The programme duration when the programme begins. • 0:00 and CLEAN when the programme is completed.
ENGLISH 7 4. CONTROL PANEL 2 1 1 2 3 4 5 3 On/off button Display Zeitvorwahl / Départ Différé button Program button MyFavourite button 4 6 7 8 9 5 6 7 8 9 TimeSaver button XtraDry button XtraHygiene button Indicators 4.1 Indicators Indicator Description Salt indicator. It is on when the salt container needs refilling. Rinse aid indicator. It is on when the rinse aid dispenser needs refill‐ ing. End indicator. It is on when the programme is completed. 5.
www.electrolux.com Programme Degree of soil Type of load Programme phases Options P5 Gläser / Verre4) • Normal or light soil Delicate crock‐ ery and glass‐ ware • • • Wash 45 °C Rinses Dry • XtraDry P4 Quick 30 Min.
ENGLISH Programme 1) Water (l) Energy (kWh) Duration (min) P4 Quick 30 Min. 10 0.7 30 P7 Vorspülen / Prélav‐ age 4 0.1 14 8 - 10 1.1 - 1.2 225 - 235 P6 ExtraSilent 9 1) The pressure and the temperature of the water, the variations of the mains supply, the options and the quantity of dishes can change the values. 5.2 Information for test institutes To receive the necessary information for conducting performance tests (e.g.
www.electrolux.com 6.2 The water softener The water softener removes minerals from the water supply, which would have a negative effect on the washing results and on the appliance. The higher the content of these minerals, the harder your water is. Water hardness is measured in equivalent scales. The water softener should be adjusted according to the hardness of the water in your area. Your local water authority can advise you on the hardness of the water in your area.
ENGLISH However, for best drying performance, always use rinse aid. If standard detergent or multi-tablets without rinse aid are used, activate the notification to keep the rinse aid refill indicator active. How to deactivate the rinse aid empty notification Make sure the appliance is in user mode. 1. Press • . The indicators and • • , , , are off. The indicator still flashes. The display shows the current setting. – – = the rinse aid empty notification is deactivated.
www.electrolux.com – = TimeBeam deactivated. 2. Press repeatedly to change the colour. 3. Press on/off to confirm the setting. 6.7 AirDry AirDry improves the drying results with less energy consumption. How to deactivate AirDry Make sure the appliance is in user mode. 1. Press • The indicators and • • . , , , are off. The indicator still flashes. The display shows the current setting = AirDry is deactivated. – – = AirDry is activated. to change the setting. 2. Press 3.
ENGLISH 13 7. OPTIONS Desired options must be activated every time before you start a programme. It is not possible to activate or deactivate options while a programme is running. Not all options are compatible with each other. If you select non compatible options, the appliance automatically deactivates one or more of them. Only the indicators of the still active options are on.
www.electrolux.com 8. BEFORE FIRST USE 1. Make sure that the current level of the water softener agrees with the hardness of the water supply. If not, adjust the level of the water softener. 2. Fill the salt container. 3. Fill the rinse aid dispenser. 4. Open the water tap. 5. Start a programme to remove any processing residuals that can still be inside the appliance. Do not use detergent and do not load the baskets.
ENGLISH 3. Remove the spilled rinse aid with an absorbent cloth to prevent excessive foam formation. 4. Close the lid. Make sure that the lid locks into position. 15 Fill the rinse aid dispenser when the indicator (A) is clear. 9. DAILY USE 1. Open the water tap. 2. Press the on/off button to activate the appliance. Make sure that the appliance is in programme selection mode. • If the salt indicator is on, fill the salt container. • If the rinse aid indicator is on, fill the rinse aid dispenser. 3.
www.electrolux.com Opening the door while the appliance operates Opening the door while a programme is running stops the appliance. It may affect the energy consumption and the programme duration. After closing the door, the appliance continues from the point of interruption. If the door is opened for more than 30 seconds during the drying phase, the running programme ends. It does not happen if the door is opened by AirDry function.
ENGLISH • • • • In areas with hard and very hard water we recommend to use plain dishwasher detergent (powder, gel, tablets containing no additional agents), rinse aid and salt separately for optimal cleaning and drying results. At least once a month run the appliance with the use of appliance cleaner which is particularly suitable for this purpose. Detergent tablets do not fully dissolve with short programmes.
www.electrolux.com 11. CARE AND CLEANING WARNING! Before maintenance, deactivate the appliance and disconnect the mains plug from the main socket. Dirty filters and clogged spray arms decrease the washing results. Make a check regularly and, if necessary, clean them. 3. Remove the flat filter (A). 4. Wash the filters. 11.1 Cleaning the filters The filter system is made of 3 parts. C B A 5. Make sure that there are no residues of food or soil in or around the edge of the sump. 6.
ENGLISH • • 19 Only use neutral detergents. Do not use abrasive products, abrasive cleaning pads or solvents. 11.4 Internal cleaning • • CAUTION! An incorrect position of the filters can cause bad washing results and damage to the appliance. 11.2 Cleaning the spray arms Do not remove the spray arms. If the holes in the spray arms are clogged, remove remaining parts of soil with a thin pointed object. • • Carefully clean the appliance, including the rubber gasket of the door, with a soft damp cloth.
www.electrolux.com Problem and alarm code Possible cause and solution The programme does not start. • • • The appliance does not fill with water. The display shows • • or . • • • The appliance does not drain the water. The display shows . • • • • The anti-flood device is on. • The display shows . Make sure that the appliance door is closed. If the delay start is set, cancel the setting or wait for the end of the countdown. The appliance recharges the resin inside the water softener.
ENGLISH Problem and alarm code Possible cause and solution Rattling or knocking sounds from the inside of the appliance. • The tableware is not properly arranged in the bas‐ kets. Refer to basket loading leaflet. Make sure that the spray arms can rotate freely. • The appliance trips the cir‐ • cuit-beaker. The amperage is insufficient to supply simultaneous‐ ly all the appliances in use. Check the socket amper‐ age and the capacity of the meter or turn off one of the appliances in use.
www.electrolux.com Problem Possible cause and solution The dishes are wet. • • • • • For the best drying performance, activate XtraDry and AirDry . The programme does not have a drying phase or has a drying phase with low temperature. The rinse aid dispenser is empty. The quality of the rinse aid can be the cause. The quality of the multi-tablets can be the cause. Try a different brand or activate the rinse aid dis‐ penser and use rinse aid and multi-tablets together.
ENGLISH Problem Possible cause and solution Dull, discoloured or chipped tableware. • • • • 23 Make sure that only dishwasher-safe items are washed in the appliance. Load and unload the basket carefully. Refer to bas‐ ket loading leaflet. Place delicate items in the upper basket. For washing delicate items and glassware, select the dedicated programme. Refer to "Pro‐ grammes". Refer to "Before first use", "Daily use" or "Hints and tips" for other possible causes. 13.
www.electrolux.com 14. ADDITIONAL TECHNICAL INFORMATION Dimensions Width / height / depth (mm) 546 / 759 / 550 Electrical connection 1) Voltage (V) 220 - 240 Frequency (Hz) 50 bar (minimum and maximum) 0.5 - 8 MPa (minimum and maximum) 0.05 - 0.8 Cold water or hot water 2) max 60 °C Water supply pressure Water supply 1) Refer to the rating plate for other values. 2) If the hot water comes from alternative source of energy (e.g.
ENGLISH electronic appliances. Do not dispose of appliances marked with the symbol with the household waste. Return the product to your local recycling facility or contact your municipal office. For Switzerland: Where should you take your old equipment? Anywhere that sells new equipment or hand it in to official SENS collection points or official SENS recycling firms. The list of official SENS collection points can be found at www.erecycling.
www.electrolux.com INHALTSVERZEICHNIS 1. SICHERHEITSHINWEISE................................................................................27 2. SICHERHEITSANWEISUNGEN...................................................................... 29 3. GERÄTEBESCHREIBUNG.............................................................................. 31 4. BEDIENFELD................................................................................................... 32 5. PROGRAMME..................................
DEUTSCH 1. 27 SICHERHEITSHINWEISE Lesen Sie vor der Montage und dem Gebrauch des Geräts zuerst die Gebrauchsanleitung. Bei Verletzungen oder Schäden infolge nicht ordnungsgemäßer Montage oder Verwendung des Geräts übernimmt der Hersteller keine Haftung. Bewahren Sie die Anleitung immer an einem sicheren und zugänglichen Ort zum späteren Nachschlagen auf. 1.
www.electrolux.com Bauernhöfe, Personalküchenbereiche in Geschäften, Büros und anderen Arbeitsumfeldern. – Für Gäste in Hotels, Motels, Pensionen und anderen wohnungsähnlichen Räumlichkeiten. Nehmen Sie keine technischen Änderungen am Gerät vor. Der Betriebswasserdruck (Mindest- und Höchstdruck) muss zwischen 0.5 (0.05) / 8 (0.8) bar (MPa) liegen Beachten Sie, dass die Höchstzahl an Maßgedecken 12 beträgt.
DEUTSCH 29 2. SICHERHEITSANWEISUNGEN 2.1 Montage • • • • • • WARNUNG! Die Montage des Geräts darf nur von einer qualifizierten Fachkraft durchgeführt werden. • Entfernen Sie das gesamte Verpackungsmaterial. Montieren Sie ein beschädigtes Gerät nicht und benutzen Sie es nicht. Halten Sie sich an die mitgelieferte Montageanleitung. Seien Sie beim Umsetzen des Gerätes vorsichtig, da es sehr schwer ist. Tragen Sie stets Sicherheitshandschuhe und festes Schuhwerk.
www.electrolux.com • WARNUNG! Gefährliche Spannung. Drehen Sie sofort den Wasserhahn zu und ziehen Sie den Netzstecker aus der Steckdose, wenn der Wasserzulaufschlauch beschädigt ist. Wenden Sie sich für den Austausch des Wasserzulaufschlauchs an den autorisierten Kundendienst. 2.4 Gebrauch • • • • • • Setzen oder stellen Sie sich niemals auf die geöffnete Gerätetür. Geschirrspüler-Reinigungsmittel sind gefährlich. Beachten Sie die Sicherheitsanweisungen auf der Reinigungsmittelverpackung.
DEUTSCH 3. GERÄTEBESCHREIBUNG 1 2 11 10 1 2 3 4 5 6 9 8 7 Mittlerer Sprüharm Unterer Sprüharm Siebe Typenschild Salzbehälter Entlüftung 3.1 TimeBeam TimeBeam projiziert folgende Informationen auf den Boden unter der Gerätetür: • Die Programmdauer am Programmstart. • 0:00 und CLEAN am Programmende. • DELAY und die Countdown-Dauer am Anfang des Countdowns der Zeitvorwahl. • Einen Fehlercode bei einer Störung des Geräts.
www.electrolux.com Wird AirDry während der Trockenphase eingeschaltet, ist die Projektion auf dem Boden möglicherweise nicht vollständig sichtbar. Die verbleibende Zeit des laufenden Programms kann dann auf dem Display des Bedienfelds überprüft werden. 4. BEDIENFELD 2 1 1 2 3 4 5 Taste „Ein/Aus“ Display Zeitvorwahl / Départ Différé Taste Program Taste MyFavourite Taste 3 4 6 7 8 9 5 6 7 8 9 TimeSaver Taste XtraDry Taste XtraHygiene Taste Kontrolllampen 4.
DEUTSCH Programm Verschmutzungs‐ Programmphasen grad Beladung P1 ECO1) • • P2 AutoSense2) • • P3 Pro3) • P5 Gläser / Ver‐ re4) • • • P4 Quick 30 Min.
www.electrolux.com Programm Verschmutzungs‐ Programmphasen grad Beladung P6 ExtraSilent 7) • • Normaler Ver‐ schmutzungs‐ grad Geschirr und Besteck • • • • Optionen Vorspülen • Hauptspülgang 50 °C Spülen Trocknen XtraDry 1) Dieses Programm gewährleistet den wirtschaftlichsten Wasser- und Energieverbrauch für normal verschmutztes Geschirr und Besteck. Dies ist das Standardprogramm für Prüfinstitu‐ te. 2) Das Gerät erkennt den Verschmutzungsgrad und die Anzahl der Geschirrteile in den Kör‐ ben.
DEUTSCH Programm1) Wasserverbrauch (l) Energieverbrauch (kWh) Dauer (Min.) 8 - 10 1.1 - 1.2 225 - 235 P6 ExtraSilent 35 1) Druck und Temperatur des Wassers, die Schwankungen in der Stromversorgung, die ausgewählten Optionen und die Geschirrmenge können die Werte verändern. 5.2 Informationen für Prüfinstitute Wenn Sie Informationen zur Durchführung von Leistungsprüfungen (z.B.
www.electrolux.com werden. Ihr lokales Wasserwerk kann Sie über die Wasserhärte in Ihrem Gebiet informieren. Der Wasserenthärter muss unbedingt auf die richtige Stufe eingestellt werden, um gute Spülergebnisse zu garantieren.
DEUTSCH sind, können Sie die Klarspülmittelnachfüllanzeige ausschalten. Für eine bessere Trocknungsleistung empfehlen wir jedoch stets Klarspülmittel zu verwenden. Einstellen der Klarspülmittelstufe Stellen Sie sicher, dass sich das Gerät im Benutzermodus befindet. Verwenden Sie die üblichen Reinigungsmittel oder MultiReinigungstabletten ohne Klarspülmittel, schalten Sie die Klarspülmittelnachfüllanzeige ein. 1. Drücken Sie • • und • • . Die Kontrolllampen , , , erlöschen.
www.electrolux.com – = das akustische Signal ist eingeschaltet. Während der Trockenphase wird die Tür automatisch geöffnet und bleibt einen Spaltbreit offen. 2. Drücken Sie zum Ändern der Einstellung. 3. Drücken Sie Ein/Aus zum Bestätigen der Einstellung. VORSICHT! Versuchen Sie nicht, die Gerätetür innerhalb der ersten 2 Minuten nach der automatischen Öffnung zu schließen. Andernfalls kann das Gerät beschädigt werden.
DEUTSCH 39 3. Drücken Sie Ein/Aus zum Bestätigen der Einstellung. Sie können verfügbare Optionen mit dem Programm einstellen. 6.8 MyFavourite 2. Halten Sie gedrückt, bis die zugehörige Kontrolllampe leuchtet. Mit dieser Option können Sie das Programm, das Sie am häufigsten benutzen, einstellen und speichern. Es kann nur ein Programm gespeichert werden. Wenn Sie ein anderes Programm speichern, wird das zuvor gespeicherte Programm gelöscht. So speichern Sie das Programm MyFavourite: 1.
www.electrolux.com Das Display zeigt die aktualisierte Programmdauer an. 7.2 TimeSaver Mit dem TimeSaver können Sie die Dauer des gewählten Programms um etwa 50% verkürzen. Die Spülergebnisse entsprechen denen einer normalen Programmdauer. Die Trockenergebnisse können beeinträchtigt werden. Wenn diese Option eingeschaltet ist, erhöht sich der Wasserdruck und die Wassertemperatur. Die Spül- und Trockenphasen verkürzen sich.
DEUTSCH 41 8.2 Füllen des KlarspülmittelDosierers A B 4. Schütteln Sie den Trichter leicht am Griff, damit auch die verbleibenden Körner in den Behälter gelangen. 5. Entfernen Sie das Salz, das sich um die Öffnung des Salzbehälters herum angesammelt hat. C VORSICHT! Verwenden Sie ausschließlich Klarspülmittel für Geschirrspüler. 6. Drehen Sie den Deckel des Salzbehälters im Uhrzeigersinn, um den Salzbehälter zu schließen. VORSICHT! Beim Befüllen des Salzbehälters können Wasser und Salz austreten.
www.electrolux.com 9.1 Verwenden des Reinigungsmittels A B angezeigt, anschließend erscheint die Programmdauer. • Drücken Sie zur Auswahl des MyFavourite-Programms . Die dem Programm MyFavourite zugeordneten Kontrolllampen der Optionen leuchten auf. 4. Stellen Sie die verfügbaren Optionen ein. 5. Schließen Sie die Gerätetür, um das Programm zu starten. • Starten eines Programms mit Zeitvorwahl C VORSICHT! Verwenden Sie nur Reinigungsmittel für Geschirrspüler. 1.
DEUTSCH Abbrechen einer eingestellten Zeitvorwahl während des Countdowns 43 Alle Tasten außer der Taste Ein/Aus sind inaktiv. und gleichzeitig Halten Sie gedrückt, bis sich das Gerät im Programmwahlmodus befindet. 1. Drücken Sie die Taste Ein/Aus oder warten Sie, bis das Gerät über die Funktion Auto Off automatisch ausgeschaltet wird. Wenn Sie die Tür öffnen, bevor die Funktion Auto Off eingeschaltet wird, wird das Gerät automatisch ausgeschaltet. 2. Schließen Sie den Wasserhahn.
www.electrolux.com • • • Schalten Sie das Gerät mindestens einmal im Monat mit einem Geschirrspülerreinigungsmittel, das speziell für diesen Zweck vorgesehen ist, ein. Geschirrspüler-Tabs lösen sich bei kurzen Programmen nicht vollständig auf. Wir empfehlen, die Tabletten nur mit langen Programmen zu verwenden, damit keine Reinigungsmittel-Rückstände auf dem Geschirr zurückbleiben. Verwenden Sie nicht mehr als die angegebene Reinigungsmittelmenge.
DEUTSCH 45 11. REINIGUNG UND PFLEGE WARNUNG! Schalten Sie das Gerät immer aus und ziehen Sie den Netzstecker aus der Steckdose, bevor Reinigungsarbeiten durchgeführt werden. Verschmutzte Filter und verstopfte Sprüharme beeinträchtigen das Spülergebnis. Prüfen Sie die Filter regelmäßig und reinigen Sie diese, falls nötig. 2. Nehmen Sie den Filter (C) aus dem Filter (B). 3. Entfernen Sie den flachen Filter (A). 11.1 Reinigen der Filter Das Filtersystem besteht aus 3 Teilen. 4. Reinigen Sie die Filter.
www.electrolux.com verstopft sind, reinigen Sie sie mit einem dünnen spitzen Gegenstand. 11.3 Reinigen der Außenseiten • • • 7. Bauen Sie die Filter (B) und (C) wieder zusammen. 8. Setzen Sie den Filter (B) in den flachen Filter (A) ein. Drehen Sie ihn nach rechts, bis er einrastet. 11.4 Reinigung des Geräteinnenraums • • • VORSICHT! Eine falsche Anordnung der Filter führt zu schlechten Spülergebnissen und kann das Gerät beschädigen. 11.
DEUTSCH Störung und Alarmcode Mögliche Ursache und Abhilfe Das Gerät lässt sich nicht einschalten. • Das Programm startet nicht. • • • • Es läuft kein Wasser in das • Gerät. • Im Display erscheint oder . • • • Das Gerät pumpt das Wasser nicht ab. Im Display erscheint • • . • • Das Überlaufschutzsystem • ist eingeschaltet. Im Display erscheint 47 Vergewissern Sie sich, dass der Netzstecker in die Netzsteckdose eingesteckt ist.
www.electrolux.com Störung und Alarmcode Mögliche Ursache und Abhilfe Aus der Gerätetür tritt ein wenig Wasser aus. • Das Gerät ist nicht ausgerichtet. Schrauben Sie die Schraubfüße weiter hinein oder weiter heraus (falls vorhanden). Die Gerätetür ist nicht mittig zur Wanne positioniert. Stellen Sie den hinteren Fuß ein (sofern vorhanden). • Die Gerätetür ist schwer zu • schließen. Das Gerät ist nicht ausgerichtet. Schrauben Sie die Schraubfüße weiter hinein oder weiter heraus (falls vorhanden).
DEUTSCH Störung Mögliche Ursache und Abhilfe Nicht zufriedenstellende Trocknungsergebnisse. • • • • • Weiße Streifen oder blau schimmernder Belag auf Gläsern und Geschirr. • Wasserflecken und andere Flecken auf Gläsern und Geschirr. • Das Geschirr ist nass. • • • • • • • Das Geschirr stand zu lange im geschlossenen Gerät. Es ist kein Klarspülmittel vorhanden oder die Klar‐ spülmittelmenge ist nicht ausreichend. Stellen Sie eine höhere Klarspülmittelmenge ein.
www.electrolux.com Störung Mögliche Ursache und Abhilfe Am Ende des Programms befinden sich Reinigungs‐ mittelreste im Behälter. • • • Das Reinigungsmittel-Tab blieb im Behälter ste‐ cken und wurde daher nicht vollständig vom Was‐ ser mitgenommen. Das Wasser kann das Reinigungsmittel nicht aus dem Behälter ausspülen. Achten Sie darauf, dass der Sprüharm nicht blockiert oder verstopft ist.
DEUTSCH Energieeffizienzklasse 51 A+++ Energieverbrauch in kWh pro Jahr, basierend auf 280 Standard- 208 Reinigungszyklen bei Verwendung von kaltem Wasser und der Modi mit wenig Energiebedarf. Der tatsächliche Verbrauch hängt davon ab, wie das Gerät verwendet wird Energieverbrauch des Standard-Reinigungs-Zyklus (kWh) 0.736 Energieverbrauch im OFF-Modus (W) 0.10 Energieverbauch im nicht-ausgeschalteten Zustand (W) 5.
15. www.electrolux.com CH GARANTIE Kundendienst Servicestellen Industriestrasse 10 5506 Mägenwil Le Trési 6 1028 Préverenges Via Violino 11 6928 Manno Morgenstrasse 131 3018 Bern Zürcherstrasse 204E 9000 St. Gallen Seetalstrasse 11 6020 Emmenbrücke Schlossstrasse 1 4133 Pratteln Comercialstrasse 19 7000 Chur Ersatzteilverkauf Industriestrasse 10, 5506 Mägenwil, Tel. 0848 848 111 Fachberatung/Verkauf Badenerstrasse 587, 8048 Zürich, Tel.
DEUTSCH 53
www.electrolux.
DEUTSCH 55
117876172-A-402018 www.electrolux.