GA55SLV EN DE Dishwasher Geschirrspüler User Manual Benutzerinformation 2 26
www.electrolux.com CONTENTS 1. SAFETY INFORMATION....................................................................................3 2. SAFETY INSTRUCTIONS..................................................................................4 3. PRODUCT DESCRIPTION................................................................................ 6 4. CONTROL PANEL............................................................................................. 7 5. PROGRAMMES.....................................
ENGLISH 1. 3 SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference. 1.
www.electrolux.com • • • • • • • • • The operating water pressure (minimum and maximum) must be between 0.5 (0.05) / 8 (0.8) bar (MPa) Obey the maximum number of 12 place settings. If the supply cord is damaged, it must be replaced by the manufacturer, its Authorised Service Centre or similarly qualified persons in order to avoid a hazard. Put the cutlery in the cutlery basket with the sharp ends pointing down or put them in the cutlery drawer in a horizontal position with the sharp edges down.
ENGLISH • • • • Connect the mains plug to the mains socket only at the end of the installation. Make sure that there is access to the mains plug after the installation. Do not pull the mains cable to disconnect the appliance. Always pull the mains plug. This appliance complies with the E.E.C. Directives. UK and Ireland only. This appliance is fitted with a 13 A mains plug. If it is necessary to change the mains plug fuse, use only a 13 A ASTA (BS 1362) fuse. 2.
www.electrolux.com 3. PRODUCT DESCRIPTION 1 2 11 10 1 2 3 4 5 6 9 8 7 Upper spray arm Lower spray arm Filters Rating plate Salt container Air vent 4 6 5 7 8 9 10 11 Rinse aid dispenser Detergent dispenser Cutlery basket Lower basket Upper basket 3 3.1 TimeBeam TimeBeam displays the following information on the floor below the appliance door: • The programme duration when the programme begins. • 0:00 and CLEAN when the programme is completed.
ENGLISH 7 4. CONTROL PANEL 2 1 3 5 4 1 On/off button 2 Display 3 Zeitvorwahl / Départ Différé touch button 4 Program touch button 5 MyFavourite touch button 6 7 8 9 6 7 8 9 TimeSaver touch button XtraDry touch button XtraHygiene touch button Indicators 4.1 Indicators Indicator Description Salt indicator. It is on when the salt container needs refilling. Rinse aid indicator. It is on when the rinse aid dispenser needs refill‐ ing. End indicator. It is on when the programme is completed. 5.
www.electrolux.
ENGLISH 9 5.1 Consumption values Water (l) Energy (kWh) Duration (min) 9.9 0.736 239 P2 AutoSense 7 - 12 0.6 - 1.4 50 - 163 P5 ProZone 13 - 14 1.2 - 1.5 150 - 160 12.5 - 14.5 1.4 - 1.7 175 - 190 10 - 12 0.9 - 1.0 70 - 80 P4 30 Min 10 0.7 30 P8 Vorspülen / Prélav‐ age 4 0.1 14 8 - 10 1.1 - 1.
www.electrolux.com , , , , and indicators flash and the display is blank. How to set the programme selection mode The appliance is in programme selection mode when the display shows the programme number P1. After activation, the appliance is in programme selection mode by default. If not, set the programme selection mode the following way: Press and hold simultaneously and 6.
ENGLISH How to set the water softener level 11 2. Press to change the setting. 3. Press on/off to confirm the setting. Make sure the appliance is in user mode. 6.4 The rinse aid level 1. Press It is possible to set the released quantity of rinse aid between level 1 (minimum quantity) and level 6 (maximum quantity). Level 0 deactivates the rinse aid dispenser and no rinse aid is released. • . The indicators and • • , , , are off. The indicator still flashes.
www.electrolux.com • • The indicator still flashes. The display shows the current setting. – = the acoustic signal is deactivated. – = the acoustic signal is activated. During the drying phase, the door opens automatically and remains ajar. CAUTION! Do not try to close the appliance door within 2 minutes after automatic opening. This can cause damage to the appliance. If, afterwards, the door is closed for another 3 minutes, the running programme ends. 2. Press to change the setting. 3.
ENGLISH How to save the MyFavourite programme • • 1. Set the chosen programme. It is also possible to set applicable options together with the programme. • 2. Press and hold indicator is on. until the related 13 The MyFavourite indicator is on. The display shows the number and the duration of the programme. If options are saved together with the programme, the indicators related to the options are on. How to set the MyFavourite programme Press . 7.
www.electrolux.com The display shows the updated programme duration. How to activate XtraHygiene 7.3 XtraHygiene Press . The related indicator is on. The display shows the updated programme duration. This option provides better hygiene results by keeping the temperature at 70 °C for at least 10 minutes during the last rinsing phase. 8. BEFORE FIRST USE 1. Make sure that the current level of the water softener agrees with the hardness of the water supply.
ENGLISH 8.2 How to fill the rinse aid dispenser A B 15 CAUTION! Only use rinse aid designed specifically for dishwashers. 1. Open the lid (C). 2. Fill the dispenser (B) until the rinse aid reaches the marking ''MAX''. 3. Remove the spilled rinse aid with an absorbent cloth to prevent excessive foam formation. 4. Close the lid. Make sure that the lid locks into position. Fill the rinse aid dispenser when the indicator (A) is clear. C 9. DAILY USE 1. Open the water tap. 2.
www.electrolux.com approximately 3 seconds and then shows the programme duration. • To select the MyFavourite programme, press . • The indicators of the options related to the MyFavourite programme are on. 4. Set the applicable options. 5. Close the appliance door to start the programme. Starting a programme with delay start 1. Set a programme. 2. Press repeatedly until the display shows the desired delay time (from 1 to 24 hours). The indicator is on. 3.
ENGLISH 17 10. HINTS AND TIPS 10.1 General Follow the hints below to ensure optimal cleaning and drying results in daily use and to help you protect the environment. • • • • • • Remove larger residues of food from the dishes into the waste bin. Do not pre-rinse dishes by hand. When needed, select a programme with a prewash phase. Always use the whole space of the baskets. Make sure that items in the baskets do not touch or cover each other. Only then can the water completely reach and wash the dishes.
www.electrolux.com 10.5 Before starting a programme • Before you start the selected programme, make sure that: 10.6 Unloading the baskets • • • • • • The filters are clean and correctly installed. The cap of the salt container is tight. The spray arms are not clogged. There is enough salt and rinse aid (unless you use multi-tablets). The arrangement of the items in the baskets is correct. The programme is suitable to the type of load and the degree of soil.
ENGLISH 19 CAUTION! An incorrect position of the filters can cause bad washing results and damage to the appliance. 11.2 Cleaning the spray arms Do not remove the spray arms. If the holes in the spray arms are clogged, remove remaining parts of soil with a thin pointed object. 5. Make sure that there are no residues of food or soil in or around the edge of the sump. 6. Put back in place the flat filter (A). Make sure that it is correctly positioned under the 2 guides. 11.
www.electrolux.com 12. TROUBLESHOOTING WARNING! Improper repair of the appliance may pose a danger to the safety of the user. Any repairs must be performed by qualified personnel. to contact an Authorised Service Centre. Refer to the below table for information on possible problems. With some problems, the display shows an alarm code. The majority of problems that may occur can be solved without the need Problem and alarm code Possible cause and solution You cannot activate the appliance.
ENGLISH Problem and alarm code Possible cause and solution The programme lasts too long. • 21 If the delay start option is set, cancel the delay set‐ ting or wait for the end of the countdown. Activate the TimeSaver option to reduce the pro‐ gramme duration. Activating options can increase the programme dura‐ tion. • • The remaining time in the display increases and skips nearly to the end of the programme duration. • This is not a defect. The appliance is working cor‐ rectly.
www.electrolux.com Problem Possible cause and solution Poor drying results. • • • • • Tableware has been left for too long inside the closed appliance. There is no rinse aid or the dosage of rinse aid is not sufficient. Adjust the rinse aid level to a higher level. Plastic items may need to be towel dried. For the best drying performance, activate XtraDry and AirDry. We recommend to always use rinse aid, even in combination with multi-tablets.
ENGLISH Problem Possible cause and solution Limescale deposits on the • tableware, on the tub and on • the inside of the door. • • • • • Dull, discoloured or chipped tableware. 23 • • • • The level of salt is low. Check the salt indicator. The cap of the salt container is loose. Your tap water is hard. Refer to "The water soft‐ ener". Use salt and set regeneration of the water softener even when multi-functional tablets are used. Refer to "The water softener".
www.electrolux.com Drying efficiency class on a scale from G (least efficient) to A (most efficient) A The ‘standard programme’ is the standard cleaning cycle to which the information in the label and the fiche relates. This pro‐ gramme is suitable to clean normally soiled tableware and is the most efficient programme in terms of combined energy and wa‐ ter consumption. It is indicated as "Eco" programme.
ENGLISH Spare parts service Industriestrasse 10, 5506 Mägenwil, Tel. 0848 848 111 Specialist advice/Sale Badenerstrasse 587, 8048 Zürich, Tel. 044 405 81 11 Warranty For each product we provide a two-year guarantee from the date of purchase or delivery to the consumer (with a guarantee certificate, invoice or sales receipt serving as proof). The 16. ENVIRONMENTAL CONCERNS Recycle materials with the symbol . Put the packaging in relevant containers to recycle it.
www.electrolux.com INHALTSVERZEICHNIS 1. SICHERHEITSHINWEISE................................................................................27 2. SICHERHEITSANWEISUNGEN...................................................................... 29 3. GERÄTEBESCHREIBUNG.............................................................................. 31 4. BEDIENFELD................................................................................................... 32 5. PROGRAMME..................................
DEUTSCH 1. 27 SICHERHEITSHINWEISE Lesen Sie vor der Montage und dem Gebrauch des Geräts zuerst die Gebrauchsanleitung. Bei Verletzungen oder Schäden infolge nicht ordnungsgemäßer Montage oder Verwendung des Geräts übernimmt der Hersteller keine Haftung. Bewahren Sie die Anleitung immer an einem sicheren und zugänglichen Ort zum späteren Nachschlagen auf. 1.
www.electrolux.com Bauernhöfe, Personalküchenbereiche in Geschäften, Büros und anderen Arbeitsumfeldern. – Für Gäste in Hotels, Motels, Pensionen und anderen wohnungsähnlichen Räumlichkeiten. Nehmen Sie keine technischen Änderungen am Gerät vor. Der Betriebswasserdruck (Mindest- und Höchstdruck) muss zwischen 0.5 (0.05) / 8 (0.8) bar (MPa) liegen Beachten Sie, dass die Höchstzahl an Maßgedecken 12 beträgt.
DEUTSCH 29 2. SICHERHEITSANWEISUNGEN 2.1 Montage • • • • • • WARNUNG! Die Montage des Geräts darf nur von einer qualifizierten Fachkraft durchgeführt werden. • Entfernen Sie das gesamte Verpackungsmaterial. Montieren Sie ein beschädigtes Gerät nicht und benutzen Sie es nicht. Halten Sie sich an die mitgelieferte Montageanleitung. Seien Sie beim Umsetzen des Gerätes vorsichtig, da es sehr schwer ist. Tragen Sie stets Sicherheitshandschuhe und festes Schuhwerk.
www.electrolux.com • WARNUNG! Gefährliche Spannung. Drehen Sie sofort den Wasserhahn zu und ziehen Sie den Netzstecker aus der Steckdose, wenn der Wasserzulaufschlauch beschädigt ist. Wenden Sie sich für den Austausch des Wasserzulaufschlauchs an den autorisierten Kundendienst. 2.4 Gebrauch • • • • • • Setzen oder stellen Sie sich niemals auf die geöffnete Gerätetür. Geschirrspüler-Reinigungsmittel sind gefährlich. Beachten Sie die Sicherheitsanweisungen auf der Reinigungsmittelverpackung.
DEUTSCH 3. GERÄTEBESCHREIBUNG 1 2 11 10 1 2 3 4 5 6 9 8 7 Mittlerer Sprüharm Unterer Sprüharm Siebe Typenschild Salzbehälter Entlüftung 3.1 TimeBeam TimeBeam projiziert folgende Informationen auf den Boden unter der Gerätetür: • Die Programmdauer am Programmstart. • 0:00 und CLEAN am Programmende. • DELAY und die Countdown-Dauer am Anfang des Countdowns der Zeitvorwahl. • Einen Fehlercode bei einer Störung des Geräts.
www.electrolux.com Wird AirDry während der Trockenphase eingeschaltet, ist die Projektion auf dem Boden möglicherweise nicht vollständig sichtbar. Die verbleibende Zeit des laufenden Programms kann dann auf dem Display des Bedienfelds überprüft werden. 4.
DEUTSCH Programm Verschmutzungs‐ Programmphasen grad Beladung P1 Eco1) • • P2 AutoSense2) P5 ProZone 3) • • • • P3 Intensiv / In‐ tensif4) • P6 Gläser / Ver‐ re5) • • • P4 30 Min6) • • P8 Vorspülen / Prélavage7) • Optionen Normaler Ver‐ schmutzungs‐ grad Geschirr und Besteck • • • • Vorspülen • Hauptspülgang 50 °C • Spülen • Trocknen XtraHygiene TimeSaver XtraDry Alle Geschirr, Be‐ steck, Töpfe und Pfannen • • Vorspülen Hauptspülgang von 45 °C bis 70 °C Spülen Trocknen XtraHygien
www.electrolux.com Programm Verschmutzungs‐ Programmphasen grad Beladung P7 ExtraSilent 8) • • Normaler Ver‐ schmutzungs‐ grad Geschirr und Besteck • • • • Optionen Vorspülen • Hauptspülgang 50 °C Spülen Trocknen XtraDry 1) Dieses Programm gewährleistet den wirtschaftlichsten Wasser- und Energieverbrauch für normal verschmutztes Geschirr und Besteck. Dies ist das Standardprogramm für Prüfinstitu‐ te. 2) Das Gerät erkennt den Verschmutzungsgrad und die Anzahl der Geschirrteile in den Kör‐ ben.
DEUTSCH Wasserverbrauch (l) Energieverbrauch (kWh) Dauer (Min.) P4 30 Min 10 0.7 30 P8 Vorspülen / Préla‐ vage 4 0.1 14 8 - 10 1.1 - 1.2 225 - 235 Programm1) P7 ExtraSilent 35 1) Druck und Temperatur des Wassers, die Schwankungen in der Stromversorgung, die ausgewählten Optionen und die Geschirrmenge können die Werte verändern. 5.2 Informationen für Prüfinstitute Wenn Sie Informationen zur Durchführung von Leistungsprüfungen (z.B.
www.electrolux.com wird in gleichwertigen Einheiten gemessen. , , und blinken und das Display nichts anzeigt. Der Enthärter muss entsprechend der Wasserhärte Ihres Gebietes eingestellt werden. Ihr lokales Wasserwerk kann Sie über die Wasserhärte in Ihrem Gebiet informieren. Der Wasserenthärter muss unbedingt auf die richtige Stufe eingestellt werden, um gute Spülergebnisse zu garantieren. 6.
DEUTSCH 6.3 Klarspülmittelnachfüllanzeige 6.4 Klarspülmittelmenge Das Klarspülmittel ermöglicht das Trocknen des Geschirrs ohne Streifen und Flecken. Es wird automatisch während der heißen Spülphasen abgegeben. Ist das Klarspülmittelfach leer, wird die Klarspülmittelnachfüllanzeige eingeschaltet und weist darauf hin, dass Klarspülmittel nachgefüllt werden sollte.
www.electrolux.com • Die Kontrolllampen • blinkt Die Kontrolllampe weiterhin. Im Display wird die aktuelle Einstellung angezeigt. und • , , , erlöschen. – = das akustische Signal ist ausgeschaltet. – = das akustische Signal ist eingeschaltet. 2. Drücken Sie zum Ändern der Einstellung. 3. Drücken Sie Ein/Aus zum Bestätigen der Einstellung. 6.6 Einstellen der Farbe von TimeBeam Sie können die Farbe von TimeBeam ändern, um sie an die Farbe Ihres Küchenbodens anzupassen.
DEUTSCH • Die Kontrolllampen und • • , , , erlöschen. blinkt Die Kontrolllampe weiterhin. Im Display wird die aktuelle Einstellung angezeigt – = AirDry ist ausgeschaltet. – = AirDry ist eingeschaltet. 2. Drücken Sie zum Ändern der Einstellung 3. Drücken Sie Ein/Aus zum Bestätigen der Einstellung. 6.8 MyFavourite Mit dieser Option können Sie das Programm, das Sie am häufigsten benutzen, einstellen und speichern. Es kann nur ein Programm gespeichert werden.
www.electrolux.com Jedes Mal, wenn Eco eingeschaltet wird, wird die Option XtraDry ausgeschaltet und muss manuell ausgewählt werden. Durch das Einschalten von XtraDry wird TimeSaver ausgeschaltet und umgekehrt. So schalten Sie XtraDry ein Drücken Sie . Die zugehörige Kontrolllampe leuchtet. Das Display zeigt die aktualisierte Programmdauer an. 7.2 TimeSaver Mit dem TimeSaver können Sie die Dauer des gewählten Programms um etwa 50% verkürzen.
DEUTSCH So füllen Sie den Salzbehälter 1. Drehen Sie den Deckel des Salzbehälters gegen den Uhrzeigersinn und entfernen Sie ihn. 2. Füllen Sie 1 Liter Wasser in den Salzbehälter (nur beim ersten Mal). 3. Füllen Sie Salz für Geschirrspüler in den Salzbehälter, bis er voll ist. 41 8.2 Füllen des KlarspülmittelDosierers A B C 4. Schütteln Sie den Trichter leicht am Griff, damit auch die verbleibenden Körner in den Behälter gelangen. 5.
www.electrolux.com • Füllen Sie den Salzbehälter auf, wenn die Kontrolllampe Salz leuchtet. • Leuchtet die Kontrolllampe Klarspülmittel, füllen Sie den Klarspülmittel-Dosierer. 3. Beladen Sie die Körbe. 4. Füllen Sie Reinigungsmittel ein. 5. Stellen Sie je nach Beladung und Verschmutzungsgrad das passende Programm ein. 9.1 Verwenden des Reinigungsmittels A B 9.2 Einstellen und Starten eines Programms Starten eines Programms 1. Lassen Sie die Gerätetür einen Spaltbreit offen. 2.
DEUTSCH Öffnen der Tür während eines laufenden Programms Wenn Sie die Tür während eines laufenden Programms öffnen, stoppt das Gerät. Dies kann sich auf den Energieverbrauch und die Programmdauer auswirken. Wenn Sie die Tür wieder schließen, setzt das Gerät den Betrieb ab dem Zeitpunkt der Unterbrechung fort. Wird die Tür länger als 30 Sekunden während der Trockenphase geöffnet, wird das laufende Programm beendet. Dies geschieht nicht, wenn die Tür durch die Funktion AirDry geöffnet wird.
www.electrolux.com in-1“) verwenden. Beachten Sie die auf der Verpackung angegebenen Hinweise. Wählen Sie ein Programm, das für die Beladung und den Verschmutzungsgrad geeignet ist. Eco bietet den effizientesten Wasserund Energieverbrauch. 10.2 Gebrauch von Salz, Klarspül- und Reinigungsmittel 3. Starten Sie das kürzeste Programm mit einer Spülphase. Verwenden Sie kein Reinigungsmittel und beladen Sie die Körbe nicht. 4.
DEUTSCH • • • • Geschirrspülsalz und Klarspülmittel vorhanden sind (außer Sie verwenden Multi-Reinigungstabletten). Die Geschirrteile richtig in den Körben angeordnet sind. Das Programm sich für die Beladung und den Verschmutzungsgrad eignet. Die Reinigungsmittelmenge stimmt. 45 2. Entladen Sie zuerst den Unter- und dann den Oberkorb. Nach Abschluss des Programms kann sich noch Wasser an den Innenseiten des Geräts befinden. 10.6 Entladen der Körbe 1.
www.electrolux.com VORSICHT! Eine falsche Anordnung der Filter führt zu schlechten Spülergebnissen und kann das Gerät beschädigen. 11.2 Reinigen der Sprüharme Bauen Sie die Sprüharme nicht aus. Falls die Löcher in den Sprüharmen verstopft sind, reinigen Sie sie mit einem dünnen spitzen Gegenstand. 5. Achten Sie darauf, dass sich keine Lebensmittelreste oder Verschmutzungen in oder um den Rand der Wanne befinden. 6. Setzen Sie den flachen Filter (A) wieder ein.
DEUTSCH 47 12. FEHLERSUCHE WARNUNG! Eine unsachgemäße Reparatur des Geräts kann eine Gefahr für die Sicherheit des Benutzers darstellen. Die Reparaturarbeiten dürfen nur von qualifiziertem Personal durchgeführt werden. Die meisten Störungen, die auftreten, können behoben werden, ohne dass der autorisierte Kundendienst gerufen werden muss. Informationen zu möglichen Störungen finden Sie in der nachfolgenden Tabelle. Bei einigen Störungen zeigt das Display einen Alarmcode an.
www.electrolux.com Störung und Alarmcode Mögliche Ursache und Abhilfe Während des Betriebs stoppt und startet das Ge‐ rät mehrmals. • Das ist normal. So werden optimale Reinigungser‐ gebnisse erzielt und Strom gespart. Das Programm dauert zu lang. • Wenn die Zeitvorwahl eingestellt ist, brechen Sie die Zeitvorwahl ab, oder warten Sie, bis sie abgelaufen ist. Schalten Sie die Option TimeSaver ein, um die Pro‐ grammdauer zu verkürzen. Eingeschaltete Optionen können die Programmdauer verlängern.
DEUTSCH 49 12.1 Die Spül- und Trocknungsergebnisse sind nicht zufriedenstellend Störung Mögliche Ursache und Abhilfe Nicht zufriedenstellende Spülergebnisse. • • • Nicht zufriedenstellende Trocknungsergebnisse. • • • • • Weiße Streifen oder blau schimmernder Belag auf Gläsern und Geschirr. • Wasserflecken und andere Flecken auf Gläsern und Geschirr. • Das Geschirr ist nass. • • • • • • • Siehe „Täglicher Gebrauch“, „Tipps und Hin‐ weise“ sowie die Broschüre zum Beladen der Kör‐ be.
www.electrolux.com Störung Mögliche Ursache und Abhilfe Rostspuren am Besteck. • • Am Ende des Programms befinden sich Reinigungs‐ mittelreste im Behälter. • • • Das Spülwasser enthält zu viel Salz. Siehe „Was‐ serenthärter“. Silber- und Edelstahlbesteck wurden zusammen eingeordnet. Ordnen Sie nicht Silber- und Edel‐ stahlbesteck zusammen ein. Das Reinigungsmittel-Tab blieb im Behälter ste‐ cken und wurde daher nicht vollständig vom Was‐ ser mitgenommen.
DEUTSCH 13. PRODUKTDATENBLATT Warenzeichen Electrolux Modellkennung GA55SLV Nennleistung (Standard-Einstellungen) 12 Energieeffizienzklasse A+++ Energieverbrauch in kWh pro Jahr, basierend auf 280 Stanard208 Reinigungszyklen bei Verwendung von kaltem Wasser und der Modi mit wenig Energiebedarf. Der tatsächliche Verbrauch hängt davon ab, wie das Gerät verwendet wird Energieverbrauch des Standard-Reinigungs-Zyklus (kWh) 0.736 Energieverbrauch im OFF-Modus (W) 0.
www.electrolux.com Wasserversorgung Kalt- oder Warmwasser2) max. 60 °C 1) Weitere Werte finden Sie auf dem Typenschild. 2) Wenn Sie Warmwasser mit alternativen Energiequellen (z. B. Solaranlagen) aufbereiten, können Sie durch den Anschluss des Geräts an die Warmwasserversorgung den Energie‐ verbrauch reduzieren. 15.
DEUTSCH Für die Schweiz: Wohin mit den Altgeräten? Überall dort wo neue Geräte verkauft werden oder Abgabe bei den offiziellen SENS-Sammelstellen oder offiziellen SENS-Recyclern. Die Liste der offiziellen SENS-Sammelstellen findet sich unter www.erecycling.
www.electrolux.
DEUTSCH 55
117876792-A-402018 www.electrolux.