Electrolux Icon Built-In Side by Side Refrigerators www.ElectroluxUSA.com Safety Instructions . . . . . . . . . . .2–4 Operating Instructions Automatic Icemaker . . . . . . . . . . .10 Care and Cleaning . . . . . . . . . .12, 13 Drawers and Baskets . . . . . . . . . . . .9 Ice and Water Dispenser . . . . .10, 11 Refrigerator Doors . . . . . . . . . . . . .8 Replacing the Light Bulbs . . . . . . .14 Shelves and Bins . . . . . . . . . . . . . . .7 Temperature Controls . . . . . . . . . . .5 Water Filter .
Safety Instructions IMPORTANT SAFETY INFORMATION. READ ALL INSTRUCTIONS BEFORE USING. WARNING! Use this appliance only for its intended purpose as described in this Owner’s Manual. SAFETY PRECAUTIONS When using electrical appliances, basic safety precautions should be followed, including the following: Operating Instructions ■ This refrigerator must be properly installed and located in accordance with the Installation Instructions before it is used.
DANGER! RISK OF CHILD ENTRAPMENT PROPER DISPOSAL OF THE REFRIGERATOR Before You Throw Away Your Old Refrigerator or Freezer: Refrigerants All refrigeration products contain refrigerants, which under federal law must be removed prior to product disposal. If you are getting rid of an old refrigeration product, check with the company handling the disposal about what to do. Operating Instructions Child entrapment and suffocation are not problems of the past.
WARNING! HOW TO CONNECT ELECTRICITY Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. For personal safety, this appliance must be properly grounded. The power cord of this appliance is equipped with a 3-prong (grounding) plug, which mates with a standard 3-prong (grounding) wall outlet to minimize the possibility of electric shock hazard from this appliance. Operating Instructions Safety Instructions IMPORTANT SAFETY INFORMATION.
ElectroluxUSA.com Operating Instructions The temperature controls are preset in the factory at 37°F for the refrigerator compartment and 0°F for the freezer compartment. Allow 24 hours for the temperature to stabilize to the preset recommended settings. Installation Instructions The actual temperature may vary slightly from the set temperature based on usage and operating environment. NOTE: The refrigerator is shipped with protective film covering the temperature controls.
Water Filter Cartridge Push In and Click to Install The water filter is located in the fresh food compartment in the upper right side. When to Replace the Filter There is a replacement indicator light for the water filter cartridge on the dispenser. This light will turn amber to tell you that you need to replace the filter soon. Operating Instructions Safety Instructions About the water filter.
ElectroluxUSA.com Not all features are on all models. Refrigerator Door Bins and Freezer Door Bins All door bins, except for the deep gallon door bin and freezer bins, are adjustable and can be moved up and down to meet your storage needs. The deep gallon door bin and the freezer bins can be removed for cleaning. Do not block CAUTION: Make sure that items do not block or fall into the ice chute. Operating Instructions To remove any bin: Lift the bin up and pull it toward you.
Safety Instructions Refrigerator Doors The refrigerator doors may feel different than the ones you are used to. The special door opening/closing feature makes sure the doors close all the way and are securely sealed. The resistance you feel at the stop position will be reduced as the door is loaded with food. When opening and closing the door, you will notice a stop position. When the door is at the 90° stop position, it will automatically close.
ElectroluxUSA.com Not all features are on all models. Fruit and Vegetable Drawers Excess water that may accumulate in the bottom of the drawers should be wiped dry. Operating Instructions Adjustable Humidity Drawers Slide the control all the way to the HI setting to provide high humidity recommended for most vegetables. Slide the control all the way to the LO setting to provide lower humidity levels recommended for most fruits.
A newly installed refrigerator may take 12 to 24 hours to begin making ice. Access Door Ice Storage Bin Operating Instructions Safety Instructions About the ice and water dispenser and automatic icemaker. Ice Storage Bin To remove: Lift up the access door to reach the icemaker. Set the icemaker power switch to the O (off) position. With the access door closed, support the storage bin at the bottom while slightly lifting. Pull bin straight out.
ElectroluxUSA.com To Use the Dispenser Select Cubed Ice or Water , Crushed Ice , Express Ice . Press the glass gently against the middle of the dispenser pad. The spill shelf is not self-draining. To reduce water spotting, the shelf and its grille should be cleaned regularly. Spill Shelf If no water is dispensed when the refrigerator is first installed, there may be air in the water line system.
Cleaning the Outside The spill shelf and the area beneath it should be cleaned periodically with a mild liquid dish detergent. Dispenser drip area. Operating Instructions Safety Instructions Care and cleaning of the refrigerator. Dispenser pad. Before cleaning, lock the dispenser by pressing the LOCK/LIGHT button for 3 seconds to prevent activating the dispenser. Clean with warm water and a mild liquid dish detergent. Rinse thoroughly and wipe dry.
Preparing for Vacation For long vacations or absences, remove food and unplug the refrigerator. Clean the interior with a baking soda solution of one tablespoon (15 ml) of baking soda to one quart (1 liter) of water. Leave the doors open. If the temperature can drop below freezing, have a qualified servicer drain the water supply system to prevent serious property damage due to flooding.
Setting the controls to OFF does not remove power to the light circuit. Refrigerator Compartment—Upper Light Raise the grille panel, set the master power switch to the O (off) position and allow lamps to cool. To remove the light shield, press on the Left side of the shield and pull down. Operating Instructions Safety Instructions Replacing the light bulbs. Replace the bulbs with appliance bulbs of the same or lower wattage.
Installation Instructions Built-In Side-By-Side Refrigerators If you have questions, call 1-877-4ELECTROLUX 877-435-3287 or visit our website at: CAUTION: BEFORE YOU BEGIN Read these instructions completely and carefully. • • • • • Due to the weight and size of this refrigerator, and to reduce the risk of personal injury or damage to the product, A MINIMUM OF 4 PEOPLE ARE REQUIRED TO BRING THE UNIT INTO THE HOME AND 2 PEOPLE ARE REQUIRED FOR PROPER INSTALLATION.
Installation Instructions HARDWARE SUPPLIED • Anti-Tip brackets Anti-Tip Brackets MATERIALS REQUIRED • 36″ long, 2″ x 4″ wood block for Anti-Tip bracket installation • #12 or #14 wood screws for Anti-Tip bracket • Screws to secure refrigerator to cabinets • 1/4″ O.D. copper water line tubing.
Installation Instructions THE INSTALLATION SPACE DIMENSIONS AND CLEARANCES 25-3/8" Case Depth *Shipping height 3" 41" Case Width *Finished Width The front height may be adjusted from 83-1/2" to 84-1/2" by adjusting front and rear leveling legs a maximum of 1".
Installation Instructions Refrigerator 23-7/8" From Rear of Refrigerator 2" 1" Case Trim 2-1/2" 1-1/2" 1/2" 1/4" 3" 2-3/4" 1-3/4" 3/4" 1-1/4" 2-1/4" 1/4" 1/2" 3/4" 1" 3/4" Custom Panel (Nominal Size) Fresh Food Door 1/4" Backer Panel Top View 130° Door Swing (factory setting) Scale 1:1 18 1/2" 3/4" 1"
Installation Instructions Refrigerator Case Trim 23-7/8" From Rear of Refrigerator 1/4" 1/2" 3/4" 1" 1-1/4" 1-1/2" Fresh Food Door Backer Panel 1/4" Top View 90° Door Swing (optional setting) Scale 1:1 3/4" Custom Panel (Nominal Size) 1/2" 3/4" 1" 19
Installation Instructions 3/4″ Framed Custom Panels 3/4″ framed custom panels are secured to a 1/4″ finished backer panel. They are designed to slide into the factory installed trim, no kits required. The backer panel will be exposed on the handle side and therefore must be finished. CUSTOMIZATION BASICS: Stainless Steel Wrapped Models Stainless Steel Wrapped Refrigerators Stainless Steel wrapped refrigerators have wrapped doors and grille panels, and beveled edges.
Installation Instructions 1/4″ FRAMED PANEL DIMENSIONS If you choose to install framed panels, they must be cut to the dimensions shown. The panels will slide into the frame on the door and grille. Door 5/16" Trim Reveal 1/4" Panel IMPORTANT NOTE: Maximum weight for Fresh Food panel is 70 pounds and 30 pounds total for Freezer panels.
Installation Instructions 3/4″ FRAMED CUSTOM PANEL OPTION For a more custom appearance, 3/4″ framed custom panels may be installed on trimmed models. The overlay panel is secured to a 1/4″ finished backer panel. The assembled custom panel then slides into the trim with the same procedure described on page 33. Door 3/4" Custom Overlay Panel Overlay Panel Backer Panel 3/4" NOTE: Left-to-right offset is not equal to top-to-bottom offset. 1/4" Backer Panel .250 + .750 = 1.
Installation Instructions 3/4″ FRAMED CUSTOM WOOD PANELS Secured to a 1/4″ finished backer panel. This design provides a framed appearance. 3-1/8" Fresh Food Panel 1" Thick Max. or 3/4" Plus 1/4" Backer 3/8" 5/16" Required for Optimal Handle Clearance 3-1/8" Min. 1/4" Max.
Installation Instructions 3/4″ FRAMED CUSTOM WOOD PANELS Secured to a 1/4″ finished backer panel. This design provides a framed appearance. 1" Thick Max. or 3/4" Plus 1/4" Backer Grille Panel 1/4" 1/4" 42″ Models A 1/4″ Backer Panel 39-15/16″ 3/4″ Overlay Panel 39-7/16″ B 10-3/4″ 10-1/8″ B 5/16" A 5/16" 1" Thick Max.
Installation Instructions 3/4″ FULL-WIDTH OVERLAY CUSTOM PANELS This panel design provides a nearly trimless appearance. Fresh Food Panel 3-1/8" 3-5/8" Assemble the spacer panel onto the finished backer panel. Allow 1/2″ clearance on the top, bottom and hinge side. Allow 3-5/8″ on the handle side. Secure the panels with glue. Be sure to observe clearances shown on all sides. Secure the overlay panel to the assembled backer/spacer panel. Use glue and screws. Countersink screws into the backer panel.
Installation Instructions 3/4″ FULL-WIDTH OVERLAY CUSTOM PANELS This panel design provides a nearly trimless appearance. Assemble the spacer panel onto the backer panel. Allow 1/2″ clearance on all four sides of the grille spacer panel. Allow 1/2″ clearance on the top and hinge side, 15/16″ on the bottom and 3-5/8″ on the handle side of the upper freezer door panel. Allow 15/16″ on the top, 1/2″ clearance on the bottom and hinge side and 3-5/8″ on the handle side of the lower freezer door panel.
Installation Instructions SIDE PANELS Side panels (not supplied) must be used whenever the sides of the refrigerator will be exposed. The 1/4″ side panels will slip into the side case trim. Order side panels from your cabinet manufacturer. *Depending on installation height. GROUNDING THE REFRIGERATOR 24" IMPORTANT—Please read carefully FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE PROPERLY GROUNDED.
Installation Instructions 1 REMOVE PACKAGING Toekick Taped to Top of Unit CAUTION: Refrigerator is Top-Heavy—be careful when moving. When using an appliance dolly, handle from Freezer side only. • Carefully cut banding at the top and bottom; remove outer carton. • Slide out rear corner posts (2). • Slide carton off top of cabinet. Metal Bracket Bolts 1/2" Nuts NOTE: DO NOT LAY CABINET DOWN IN ORDER TO REMOVE SKID! • The unit is secured to the skid with six 7/16″ bolts and six 1/2″ nuts.
Installation Instructions 2 INSTALL WATER LINE • A cold water supply is required for automatic icemaker operation. The water pressure must be between 40 and 120 psi. • Route 1/4″ O.D. copper tubing between cold water line and the water connection location. • Tubing should be long enough to extend to the front of the refrigerator. Allow enough tubing to accommodate bend leading into the water line connection. NOTE: Certain types of plastic may crack or rupture with age and cause water damage to your home.
Installation Instructions 3 INSTALL SIDE PANELS 4A ALTERNATE ANTI-TIP PRECAUTIONS SKIP THIS STEP WHEN NOT USING SIDE PANELS If you are using 1/4" side panels, they should be inserted into the case trim. Fasten the panels to the refrigerator with the 3M Dual Lock adhesive strips before setting refrigerator in place. SKIP THIS STEP WHEN USING ANTI-TIP BRACKETS All Profile built-in refrigerators are Top-Heavy. They must be secured to prevent the possibility of tipping forward.
Installation Instructions 5 CONNECT POWER 7 LEVEL REFRIGERATOR • Connect refrigerator power cord plug to a properly grounded receptacle. Set the Master Power switch to the I (ON) position. All models have 4-point leveling. The front and back are supported by leveling legs. Both are accessible from the front of the refrigerator. • To level the back of the refrigerator, turn the 1/2″ hex nut located above the front wheels. Turn clockwise to raise or counterclockwise to lower the refrigerator.
Installation Instructions 8 SECURE REFRIGERATOR TO CABINETS 10 INSTALL GRILLE PANEL • Raise the grille panel to the stop position. Whenever possible, perform this step for anti-tip security. The refrigerator must be secured to prevent tipping. • Raise the grille panel to access case trim. • Drive a screw through the trim and into the adjacent cabinet using holes provided. • Follow the same procedure on the opposite side. Raise Grille Panel • Remove 4 screws on bottom trim; retain all screws.
Installation Instructions 11A INSTALL DOOR PANELS ON TRIMMED MODELS Handle Fresh Food Refrigerator Door 3/4" Custom Panel if Required Install 1/4″ Decorative Panels: • Remove Handles Open door to 90°. Remove 5 Phillips head screws from the Fresh Food and Freezer door handles; retain all screws. Lift off door handles. • Install Door Panels NOTE: Stainless steel and acrylic panels are covered with a protective film. Remove the film before installing the panel.
Installation Instructions 11B INSTALL DOOR HANDLES ON STAINLESS STEEL MODELS 1. Remove handles from cartoning and any other protective packaging. 2. Place handle over pre-installed shoulder bolts (A) that are fastened into door in four locations. 3. While supporting handle and looking at upper end cap, fasten top-most allen set screw (B) with supplied allen wrench, then fasten bottom allen set screw (C). See Figure 1. 4.
Installation Instructions 12 CONNECT WATER SUPPLY 13 TURN ON THE POWER Check to make sure that Master Power switch is in the O (OFF) position. • Set the Master Power switch to the I (ON) position. • Check to make sure power to refrigerator is on by opening refrigerator door to see if interior lights are on. Raise Grille Panel Master Power Switch Refrigerator Water Supply House Water Supply • The temperature controls are preset at 37° for the Fresh Food section and 0° for the Freezer section.
Installation Instructions 16 DOOR ALIGNMENT 14 START ICEMAKER • Stand back from the refrigerator to inspect the door alignment. • Shipping or the addition of heavy door panels may have caused the doors to move slightly out of alignment. Power Switch Feeler Arm Green Power Light • Flip the switch to I (ON). The icemaker will begin operation automatically. • Make sure nothing interferes with the sweep of the feeler arm. • Discard the first full bucket of ice cubes.
Newer refrigerators sound different from older refrigerators. Modern refrigerators have more features and use newer technology. Do you hear what I hear? These sounds are normal. ■ The new high efficiency compressor may run faster and longer than your old refrigerator and you may hear a high-pitched hum or pulsating sound while it is operating. ■ You may hear a whooshing sound when the doors close. This is due to pressure equalizing within the refrigerator.
Safety Instructions Troubleshooting tips… Troubleshooting Tips Save time and money! Review the charts on the following pages first and you may not need to call for service. Problem Installation Instructions Operating Instructions Refrigerator does not operate Possible Causes What To Do Refrigerator in defrost cycle. • Wait about 30 minutes for defrost cycle to end. Master power control set to OFF. • Set the control to an on setting. Refrigerator is unplugged.
Possible Causes What To Do Frequent “buzzing” sound Icemaker power switch is in the I (on) position, but the water supply to the refrigerator has not been connected. • Set the power switch to the O (off) position. Keeping it in the I (on) position will damage the water valve. Ice cubes have odor/taste Ice storage bin needs cleaning. • Empty and wash bin. Discard old cubes. Food transmitting odor/taste to ice cubes. • Wrap foods well. Interior of refrigerator needs cleaning.
Safety Instructions Operating Instructions Installation Instructions Problem Possible Causes What To Do Orange glow in the freezer Defrost heater is on. •This is normal. Refrigerator has odor Foods transmitting odor to refrigerator. •Foods with strong odors should be tightly wrapped. •Keep an open box of baking soda in the refrigerator; replace every three months. Interior needs cleaning. • See Care and cleaning. Door gasket on hinge side sticking or folding over.
Operating Instructions Installation Instructions Troubleshooting Tips Consumer Support 41 Safety Instructions ElectroluxUSA.
State of California Department of Health Services Water Treatment Device Certificate Number 01 - 1474 Date Issued: April 25, 2001 Trademark/Model Designation Frigidaire PureSource 2 NGFC-2000 Gibson Cool and Clean NGFC-2000 Electrolux pure advantage NGFC-2000 Replacement Elements FC-100 FC-100 FC-100 Manufacturer: Electrolux Home Products The water treatment device(s) listed on this certificate have met the testing requirements pursuant to Section 116830 of the Health and Safety Code for the following
MEMO 44