SANTO K 78800-4 i Refrigerator Operating Instructions PERFEKT IN FORM UND FUNKTION
Dear customer, Before placing your new refrigerator/freezer into operation please read these operating instructions carefully. They contain important information for safe use, for installation and for care of the appliance. Please keep these operating instructions for future reference. Pass them on to possible new owners of the appliance. These operating instructions are for use with several technically comparable models with varying accessories. Please observe the notes which apply to your model.
Contents Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Appliance Packaging Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Disposal of old Appliances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Remove transport packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Important Safety Instructions These warnings are provided in the interests of your safety. Ensure you fully understand them before installing or using the appliance. Your safety is of paramount importance. If you are unsure about the meaning of these warnings contact the Customer Care Department for assistance. 4 Intended use • The refrigerator is intended for use in the home. It is suitable for the storing of food at low temperature.
• Please make old appliances unusable prior to disposal. Pull out the mains plug, cut off the mains cable, break or remove spring or bolt catches, if fitted. By doing this you ensure that children cannot lock themselves in the appliance when playing (there is risk of suffocation!) or get themselves into other dangerous situations. • Often children cannot recognise the hazards present in household appliances.
Disposal Appliance Packaging Information All materials are environmentally sound! They can be disposed of or burned at an incinerating plant without danger. About the materials: The plastics can be recycled and are identified as follows: >PE< for polyethylene, e.g. the outer covering and the bags in the interior. >PS< for polystyrene foam, e.g. the pads, which are all free of chlorofluorocarbon.
Installation Installation Location The appliance should be set up in a well ventilated, dry room. Energy use and efficient performance of the appliance is affected by the ambient temperature. The appliance should therefore – not be exposed to direct sunlight; – not be installed next to radiators, cookers or other sources of heat; – only be installed at a location whose ambient temperature corresponds to the climate classification, for which the appliance is designed.
Installation Your refrigerator needs air Integratable models (i-appliances) The integrated door of the furniture cabinet largely seals the installation recess. i-appliances must therefore be provided with ventilation by having an opening in the furniture plinth. The warmed air must be able to be exhausted upwards through the air shaft on the furniture back. The ventilation cross-sections should be at least 200 cm2. min. 200 cm2 50 min.
Installation appliance’s door has been locked in position ☞1. The for transport by means of pins on both sides. A According to the door opening direction, remove relevant pins at the top and at the bottom. B 2. Press in the joint covers between the appliance and the kitchen furniture. D765 3. Push the appliance into the housing until stop strip (A) touches the kitchen unit. 4. Open the door and push the appliance against the side of kitchen furniture opposite to that of appliance hinges.
Installation 5. Apply blanking covers (B) as indicated. B 6. Separate parts A, B, C, D as shown in the figure. B A C D 50mm 7. Place guide (A) on the inside part of the furniture door, upper and lower positions as shown in the figure and mark the position of external holes. After having drilled holes, fix the guide with the screws supplied. A 20m m 8. Fix cover (C) on guide (A) until it clips into place.
Installation 9. Open the appliance door and the furniture door at 90°. Insert the small square (B) into guide (A). Put together the appliance door and the furniture door and mark the holes as indicated in the figure. Remove the squares and drill holes with Ø 2 mm at 8 mm from the outer edge of the door. Place the small square on the guide again and fix it with the screws supplied. 8mm A B 10. Should the lining up of the furniture door be necessary, use the clearance of slots.
Installation Power supply ☞ A correctly installed, earthed socket is required for the electrical supply. The supply must have a fuse rating of at least 10 Amps. If the socket is not accessible once the appliance is built in, the electrical installation must include suitable means of isolating the appliance from the mains (e.g. a fused spur).
1.The wire coloured green and yellow must be connected to the terminal marked with the letter “E” or by the earth symbol or coloured green and yellow. 2.The wire coloured blue must be connected to the terminal “N” or coloured black. 3.The wire coloured brown must be connected to the terminal marked “L” or coloured red. 4.Upon completion there must be no cut, or stray strands of wire present and the cord clamp must be secure over the outer sheath.
Prior to Initial Start–Up ☞ Please clean the appliance interior and all accessories prior to initial start-up (see section: “Cleaning and Care”). Starting up and temperature regulation Important! Only use the appliance when built–in! 1. Connect the appliance to the mains electricity supply. When the refrigerator compartment door is opened, the internal lighting is switched on. The temperature control knob is located on the right hand side of the refrigerator compartment. Setting “0” means: Off. 2.
Switching off the appliance ☞ To switch off the appliance, turn the temperature regulator to position "0". If the appliance is not going to be used for an extended period: 1. Remove all refrigerated packages. 2. Switch off the appliance by turning the thermostat knob to position "0". 3. Remove the mains plug or switch off or disconnect from the electricity supply. 4. Clean thoroughly (see section: “Cleaning and Care”). 5. Leave the door open to avoid the build up of odours.
Variable Inner Door The door compartments can be pulled up and removed, and inserted at other positions as needed. Correct storage For physical reasons, there are different temperature regions in the fridge. The coldest region is on the lowest storage shelf. Warmer regions are the top storage shelf, the vegetable drawer and the storage compartments on the door. The arrangement example shows at which places in the refrigerator suitable temperatures for various types of foods exist.
Cleaning and Care For hygienic reasons the appliance interior, including interior accessories, should be cleaned regularly. Warning! • The appliance must not be connected to the mains during cleaning. Danger of electrical shock. Before cleaning switch the appliance off and remove the plug from the mains, or disconnect from the electricity supply. • Never clean the appliance with a steam cleaner. Moisture could accumulate in electrical components and there is a danger of an electrical shock.
Energy Saving Tips • Do not install the appliance near boilers, radiators or other sources of heat. High ambient temperatures cause longer, more frequent operation of the compressor. • Ensure sufficient air circulation and exhaust at the appliance base and at the back wall of the appliance. Never cover air vent openings. • Do not place warm foods into the appliance. Allow warm foods to cool first. • Do not leave the door open any longer than necessary. • Do not set temperature any colder than necessary.
What to do if ... Symptom Possible Cause Remedy The compressor runs continuously. Temperature is set too cold. Turn the thermostat knob to a warmer setting temporarily. Interior lighting does not work. Light bulb is defective. Please look in the “Changing the Light Bulb” section. The food is too warm. Temperature is not properly adjusted. Door was open for an extended period. A large quantity of warm food was placed in the appliance within the last 24 hours. The appliance is near a heat source.
Changing the light bulb Warning! There is a risk of electric shocks! Before changing the light bulb, switch off the appliance and unplug it, or disconnect from the power supply. Light bulb data: 220-240 V, max. 15 W ☞1. To switch off the appliance, turn the thermostat knob to position "0". 2. Unplug the mains plug. 3. To change the light bulb, undo the screw. 4. Press the light bulb cover as shown and slide it backwards. 5. Change the defective light bulb. 6. Refit the light bulb cover and the screw. 7.
Regulations, Standards, Guidelines This appliance was designed for household use and was manufactured in accordance with the appropriate standards. The necessary measures in accordance with appliance safety legislation regulations (GSG), accident prevention regulations for refrigeration appliances (VBG 20) and the regulations of the German Society of Electrical Engineers (VDE) were observed in the manufacture of this appliance. The refrigerant circuit has been checked for leaks.
Technical terminology • Refrigerant Liquids that can be used to a generate a cooling effect are known as refrigerants. They have a relatively low boiling-point, indeed so low, that the warmth from the food stored in the fridge or freezer can cause the refrigerant to boil and vaporise. • Refrigerant Circuit Closed circulation system that contains the refrigerant. The refrigerant circuit comprises primarily of an evaporator, a compressor, a condenser and pipe work.
AEG Hausgeräte GmbH Postfach 1036 D-90327 Nürnberg http://www.aeg.hausgeraete.
