EN CONDENSING TANKLESS GAS WATER HEATER SP CALENTADOR A GAS TIPO CONDENSADO SBB800R Rev.
CONDENSING TANKLESS GAS WATER HEATER Use and Care Manual Models : EN19WI30LS EP19WI30LS EN18WI30LS EP18WI30LS FOR USE IN RESIDENTIAL APPLICATIONS IN THE UNITED STATES ONLY. NOT INTENDED FOR USE IN CANADA OR MEXICO. WARNING If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury, or death. - Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
Important Safety Information-1 To prevent damage to property and injury to the user, the icons shown below will be used to warn of varying levels of danger. Every indication is critical to the safe operation of the water heater and must be understood and observed. Potential dangers from accidents during installation and use are divided into the following four categories. Closely observe these warnings; they are critical to your safety. Icons warning of risk level This is the safety alert symbol.
(Continued) Prohibited [When supplying combustion air Air supply vent from the indoors] Do not use the water heater if the intake/ exhaust pipe is displaced, has holes, is clogged or is corroded. Be sure to do. Check whether or not the air supply vent is blocked with dust, trash, a towel, or the like. Towel Blocking the opening may result in incomplete combustion. Prohibited Do not allow anyone to change the water temperature while hot water is being used.
Important Safety Information-2 (Continued) WARNING Prohibited Do not place the exhaust vent terminal in an indoor environment by means of adding walls and ceiling (Do not enclose using corrugated sheets, etc.) Prohibited Carbon Monoxide Poisoning Hazard. Do not install this water heater in a mobile home, recreation vehicle or on a boat. Prohibited Do not use combustible chemicals such as oil, gasoline, benzene etc. in the near the heater or the exhaust vent terminal.
(Continued) Prohibited Do not allow small children to play unsupervised in the bathroom. Do not allow small children to bath unsupervised. Do not touch the power cord with wet hands. Don’t touch with a wet hand. Be sure to do. Don’t disassemble the equipment. Electric Shock. Consult the nearest Electrolux agent if the water heater location needs to be changed. $POUBDU B RVBMJmFE TFSWJDF technician for any necessary repairs, service or maintenance.
Important Safety Information-3 CAUTION Do not drink water that has been inside the unit for an extended period of time. Do not ESJOL UIF mSTU VTF PG IPU XBUFS GSPN UIF unit in the morning. This unit is only approved for installation up to 4500 ft. (1350m) above sea level. For installations at higher elevations, contact Electrolux Home Products, Inc. for Instructions. $MFBO UIF mMUFS PO UIF XBUFS JOMFU BT frequently as required by the quality of your local water.
Contents Important Safety Information ....................................................................... 2 Contents ........................................................................................................ 7 Overview of Condensing Tankless Gas Water Heater .............................. 8 General Parts Main Unit .................................................................................................... 9 Remote Controller..........................................................
Overview of Condensing Tankless Gas Water Heater This water heater is a high efficiency, fully condensing appliance. Unlike a traditional tankless water heater, a condensing type captures heat from the exhaust gas and uses it to preheat the incoming cold water as it passes through the secondary heat exchanger as illustrated below.
General Parts -1 Main Unit Indoor Wall Mounted, Power Vent/Sealed Model Intake Pipe Flue Collar Front Cover Water Drain Valve (with Water Filter) (Inside Water Inlet) ( p.22) Pressure Relief Valve Water Supply Valve Gas Supply Valve Drain Pipe Discharges the condensate. (Ex. EN18WI30LS) * The above illustration shows an example of installation. The exact installation configuration may be slightly different.
General Parts -2 Remote Controller What is actually displayed depends on how the water heater is set. Burner On Indicator Setting Buttons When burning, the indicator is lit. ( p.13 and 15) For setting the hot water temperature, the flow meter alarm, and other settings. Priority Indicator When this indicator is lit, the hot water temperature can be set. ( p.12) Temperature Setting (Ex.:110°F) Power On/Off Button For turning the heater on and off.
Initial Operation Before the first use of your water heater, make the following preparations. Follow steps 1 2 1 through 4. Open the water supply valve. OPEN CLOSED Open a hot water fixture to confirm that water is available, and then close the fixture again. Hot water fixture 3 Open the gas supply valve. 4 Turn on the power. Do not touch with wet hands. (Ex.
How to Use Setting and Using the Water Heater 2 1 (Starting with the Power Off) 1 Press the Power On/Off Button. On The temperature will be displayed on the remote control thermostat. On Previous set temperature (Ex.: 110°F) DANGER To prevent scalding: High Temperature Hot Water Heater temperatures over 125°F (52°C) can cause severe burns instantly or death from scalding. r Children, disabled and elderly are at the highest risk of being scalded. Feel water temperature before bathing or showering.
2( Set temperature. Always check the temperature setting before use. ) 3 4 Turn on hot water. Turn off the hot water. Hot Cold Check the indicator lights. On Off Water temperature When using °F mode: temperature settings below are examples. The temperature setting °F: The necessary depends on the usage, the length of piping and the time of year. ( 100 Washing dishes, etc. 105 110 115 The maximum output temperature can be set using the remote controller. ( p.
How to Use Flow Meter Alarm If the flow meter alarm is being used to indicate when a tub is full: r If any hot water is being used besides what is going into the tub, the alarm will sound before the tub is full. r If there was water in the tub before the fill began, or if the water is not shut off manually when the alarm sounds, the tub may overflow. r If there was water in the tub before the fill began, the temperature in the tub after it is full may be different from the temperature setting.
Water Temperature temperatures settings below are only examples. The °F : The temperature setting necessary will depend on the usage, An alarm will sound for ten seconds when the flow reaches the set level. ( ) the length of piping and the time of year. 100 Warm The water will continue to run unless it is manually turned off. (°C (°F) : 105 110 Warmer 115 120 Hot The temperatures settings below are only examples.
How to Use Muting the Remote Controller 1 The remote controller will emit a sound when any button is pushed. This sound can be muted if it is desired. * Initial factory setting is with sound. 1 Hold the Power On/Off Button for five seconds. Muted No sound after 5 sec. Sound Tone sounds after 5 sec. r 5IF áPX NFUFS BMBSN DBOOPU CF NVUFE r 5IF IJHI UFNQFSBUVSF XBSOJOH UPOF XIFO TFUUJOH UIF VOJU UP ' $ ' PS IJHIFS XJMM not emit a sound when muted.
How to Use Adjusting the Maximum Output Temperature 3 1 2 1 Turn off the power. 2 Press and hold the flow meter alarm set button until a sound is heard (2 sec.). 3 Tone sounds after 2 sec. Off Change the temperature using the setting buttons. Up Down The upper limit of the hot-water supply temperature can be changed to (For Fahrenheit (°F)) 100°F, 105°F, 110°F, 115°F, 120°F, 125°F, 130°F, 135°F or 140°F.
Preventing Damage from Freezing-1 CAUTION * Damage can occur from frozen water within the device and pipes even in warm environments. Be sure to read below for appropriate measures. * Repairs for damage caused by freezing are not covered by the warranty. Freezing is prevented within the device automatically by the freeze-prevention heater. Freezing cannot be prevented when the power plug is unplugged. Do not remove the power plug from the wall outlet.
Preventing Damage from Freezing-2 For EN18WI30LS, EP18WI30LS If the water heater will not be used for a long period of time, drain the water. Drain the water as follows: CAUTION High Temperature To avoid burns, wait until the equipment cools down before draining the water. The appliance will remain hot after it is turned off. Drain water into a bucket to prevent water damage. Manual Draining 1 2 3 4 5 6 7 Close the gas valve. Turn off the power button.
Preventing Damage from Freezing-3 For EN19WI30LS, EP19WI30LS If the water heater will not be used for a long period of time, drain the water. Drain the water as follows: CAUTION High Temperature To avoid burns, wait until the equipment cools down before draining the water. The appliance will remain hot after it is turned off. Drain water into a bucket to prevent water damage.
Turning the Unit Back On 1. 2. 3. 4. Check that all drain plugs are inserted. Check that all hot water fixtures are closed. 'PMMPX UIF QSPDFEVSF PO Q i*OJUJBM PQFSBUJPOu TUFQT UISPVHI Make sure that the area around the appliance is well ventilated; open a window or a door if necessary. Then, operate the unit and verify that condensate is coming out of the drain pipe.
Regular Maintenance Periodic Inspection CAUTION To prevent burns or scalding, turn off the power button and wait until the equipment cools before performing maintenance. Be sure to do. [When supplying combustion air from the indoors] air supply vent Check For smear or blockage Check For dust and soot in with dust, oil, etc. at the air supply vent. If blocked, remove the build-up with a vacuum cleaner or damp towel. the exhaust vent or exhaust vent terminal.
Periodic Maintenance Water Drain Valve (with Water Filter) If the water drain valve (with water filter) is covered with debris, the hot water may not run smoothly, or the unit may put out cold water. Check and clean the filter as explained below. * To avoid burns, wait until the equipment cools down before draining the water. The appliance will remain hot after it is turned off. 1. Close the water supply valve. 2. Open all hot water fixtures. 3.
Troubleshooting-1 Initial Operation Unit does not attempt to ignite when water is running. r $IFDL GPS SFWFSTFE QMVNCJOH PS DSPTTFE QJQFT r $IFDL UIF XBUFS ESBJO WBMWF àMUFS p.23) Unit attempts to ignite but fails. r 3FTFU VOJU BOE USZ BHBJO 5IFSF NBZ CF BJS JO UIF HBT MJOF r )BWF B QSPGFTTJPOBM DIFDL UIF HBT TVQQMZ QSFTTVSF Temperature Hot water is not available when a fixture is opened.
The water is cold when only a single fixture is open. r 5IF VOJU XJMM OPU IFBU UIF XBUFS JG UIF áPX SBUF JT MFTT UIBO 0.5 gallons (2L) per minute. Open the fixture more or open other fixtures so that a greater flow passes through the unit, and the unit should begin heating again. Fluctuations in hot water temperatures. r 4FU XBUFS UFNQFSBUVSF BU °F to 120°F or 48°C (118°F) to 50°C (122°F). This will allow you to use a higher flow of hot water thus meeting the minimum flow requirement of 0.5 (1.
Troubleshooting-2 Remote Controller The light on the power button does not come on. r )BT UIFSF CFFO B QPXFS GBJMVSF The water temperature changes after a power failure or when the power is disconnected. r 5IF UFNQFSBUVSF TFUUJOH BOE UIF áPX NFUFS BMBSN TFUUJOH may both need to be reset after a power outage. r *T UIF QPXFS DPOOFDUFE QSPQFSMZ The plastic on the surface or buttons r The surface of the remote controller is affixed with a protective sheet (to prevent surface scratching, etc.
The water appears blue. r $PMPSBUJPO UP B CMVF DPMPS NBZ CF OPUJDFE GSPN TNBMM 5IF CBUI UVC XBTI CBTJO IBT UVSOFE traces of copper ion contained in the water and fat (furring). However, there are not problems concerning blue. IFBMUI $PMPSBUJPO PG UIF CBUI UVC XBTI CBTJO DBO CF prevented by cleaning frequently. r $POEFOTBUJPO GPSNT JOTJEF UIF VOJU EVSJOH PQFSBUJPO and is discharged from the drain pipe. Frequent water discharge from the drain pipe.
åÃè·ï\é¶Ç¼Ç®í≤Ç◊Ç≠ÇæÇ≥Ç¢ åÃè·ï\é¶Ç¼Ç®í≤Ç◊Ç≠ÇæÇ≥Ç¢ Check for an Error Code on the Remote Controller If there is a problem with the unit, a numerical error code will flash on the remote controller. If this occurs, take appropriate measures as listed below. Flashing When an error code appears, the display and the operation light will flash together. Remote Controller Error Code Cause Action Ignition error Check whether the gas valve is open.
Follow-up Service-1 Requesting Service First follow the instructions in the troubleshooting section ( p.24 to p.28). If the error is not corrected, contact Electrolux Home Products, Inc. at 1-888-360-8557. We will need to know: The Model ................(check the rating plate) See p.4 for the location of the label Date of purchase ......(see the warranty) Details of problem ....(flashing error codes, etc.
Follow-up Service-2 Gas Conversion If you move to a region that uses a different type of gas or if the local gas supply is converted, replacement of the gas manifold and adjustment of the appliance will be necessary. This work must be performed by either Electrolux or a qualified service agency and will be charged for even during the warranty period. The qualified installer will also be responsible for purchasing the gas conversion kit directly from the manufacturer.
Specifications-1 r 4QFDJàDBUJPOT NBZ CF DIBOHFE XJUIPVU QSJPS OPUJDF r 5IF DBQBDJUZ NBZ EJGGFS TMJHIUMZ EFQFOEJOH PO UIF XBUFS QSFTTVSF water supply, piping conditions, and water temperature.
Specifications-2 r 4QFDJàDBUJPOT NBZ CF DIBOHFE XJUIPVU QSJPS OPUJDF r 5IF DBQBDJUZ NBZ EJGGFS TMJHIUMZ EFQFOEJOH PO UIF XBUFS QSFTTVSF water supply, piping conditions, and water temperature.
Electrolux Home Products, Inc Limited Warranty Tankless Hot Water Heaters !=:;=)6< <7 <0- <-:5; )6, +76,1<176; ;-< .7:<0 16 <01; 151<-, ')::)6
< ,+1&+2"!= + 1%" "3"+1 ,# + )" 1/,)25 /" ,$+&7"! !"#" 1 * )#2+ 1&,+ ,/ # &)2/" 1, ,+#,/* 4&1% 1%&0 // +16 +! 0"! 2-,+ )" 1/,)25 --/,3 ) ,# 4 // +16 ) &* )" 1/,)25 1 &10 0,)" +! 0,)21" !&0 /"1&,+ 4&)) 0"11)" 1%" 4 // +16 ) &* ,# 02 % !"#" 1 * )#2+ 1&,+ ,/ # &)2/" 1, ,+#,/* 4&1% 1%&0 // +16 + ,/!"/ 1, * (" ) &* 2+!"/ 1%&0 // +16 1%" 4+"/ *201 +,1 )" 1/,)25 ,/ &10 21%,/&7"! /"-/"0"+1 1&3" ,# 1%" # &)2/" ,# 1%" /,!2 1 1, ,+#,/* 1, 1%&0 // +16 +!"/ 1%&0 /