Installation Slide Instructions In Gas Cooktop
Safety (MPORTANT SAFETY(NSTRUCT(ONS .............................................. m [] [] m [] [] [] m [] [] [] m [] [] [] m [] [] [] m [] [] ))))))))))))))))))))))))))))))))))))))))))))))))))))))))))))_i!i ¸!!iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii) Safety Precautions Do notattemptto install oroperateyour unit until you have readthesafety precautions in this manual.
Safety 3 SAFETYPRECAUTIONS [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] ,,%, WARNING • Read all instructions before using the appliance. • Improper installation, adjustment, alteration, service, or maintenance can cause personal injury or property damage. Refer to these instructions and the accompanying Use & Care Manual. For assistance or additional information, consult a qualified installer, service agency, manufacturer (dealer), or the gas supplier.
Safety
Finding Information READAND SAVETHESEINSTRUCTIONS [] [] [] [] [] [] [] [] [] [] [] [] [] [] For toll-free telephone support in the U.S. and Canada: 1-877- 4ELECTROLUX (1-877-435-3287) For online support and Internet product www.electroluxusa.com information: @2005 Eiectroiux Home Products, Inc. Post Office Box 212378, Augusta, Georgia 30917, USA All rights reserved.
Finding Information TABLEOF CONTENTS Safety ..................................................................... 2 Definitions........................................................... 2 ImportantSafetyInstructions ............................... 2 SafetyPrecautions .............................................. 3 Finding Information............................................ 5 PleaseReadAndSaveThisGuide....................5 Questions? ..........................................................
Preparingfor Installation VERIFYPACKAGECONTENTS [] [] [] [] • Literature • [] [] [] [] [] [] Pack [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] • Griddle Bolts/Washers • Simmer Plate • Burner Grate Pack • Wok Stand • Burner Set • Stainless • Gas Pressure [] Steel Cleaner • LP Conversion Regulator Kit • Burner Cap Pack CABINET/COUNTER'FOP PREPARATION [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] The installation of this built-in appliance mus
Preparing for Installation Plan the installation so that the electrical pressure Figure 1 regulator are accessible E36GC76EPS: 36" (914mm) Minimum E48GC76EPS: 48" (1219mm) Minimum connection, gas shut-off stated V Minimum 30" {762turn) ...... 5,8" (16turn) Overhar_g, both sides combustib]e side wall both sides / _,2" (38ram) Typical Cour_te_op (457mm} 1 /8" Q ® J H97mm) 7 3_4" • ® ® ] • -- (g14mm) /5 1_2rr (393mm) /254mm) /0" 6 (see Figure 1).
Preparingfor Installation Figure 3 ++++++++++++++++++++++++++++++++++++++++++++++++++++++ Countertop Cut-out Dimensions Cooktop is to be installed with Downdraft Vent 36" model: E36DD75ESS; 48" model: E48DD75SS) (when Hood Vertical non-combustible surface rear wall .,_ "_. E36GC76EPS-33 _ E48GC76EPS 7/8" - 43 1/2" (860mm) I_ (1105mm) z _['_-. _1 _ / ........ I = i21 3/8" ...... (543mm) (716r_m) I i I I Backsplash i I Ii Ii / / Ii | Ii Max.
Preparing for Installation Overall Dimensions - Side Views Clearance to Combustible Rear Wall 2½Ee4r_m] OPTIONAL STAINLESS STEEL BACKSPLASH ACCBGO9 a6SI Ea6GC76EPS: ACCBD09 4SS_ E#SDC76EPS: COMBUSTIBLE REAR FWALL MATERIAL TOP OF FINISHED COUNTER_ 743 E197mm] Figure 5 Overall Cutout Clearance Optional 9" stainless steel backsplash (attaches to wall) to Dimensions Dimensions _ ............. _:_ Combusti / 10" min. to nearest combustible wall (either side of unit) Side inset s/8" 2 W' min.
Making the Gas/Electric Connection [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] Gas SupplyRequirements Check your local building codes for the proper method of installation. In the absence of local codes, this appliance should be installed in accordance with the National Fuel Gas Code ANSI Z223.1/NFPA 54. Be certain that the appliance being installed is correct for the gas service being provided. Refer to the data plate located on the bottom of the cooktop chassis.
Making the Gas/ElectricConnection LiQU(FIEDPETROLEUM(PROPANE)GAS CONVERS(ON This appliance can be used with Natural Gas and Propane the factory for use with natural gas. Gas. It is shipped from A kit for converting to LP gas is supplied with your cooktop. LP/PROPANE GAS CONVERSION". Follow the installation The kit is marked "FOR instructions which are inside the envelope. The conversion must be performed by a accordance with the kit instructions and Failure to follow instructions could result damage.
Making the Gas/Electric Connection i iiiiiiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii ElectricalSupplyRequirements iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii The correctvoltage, frequencyand amperage mustbe suppliedtothe appliance from an isolated, groundedcircuitwhich isprotectedbyaproperlysizedcircuit iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiiiiiiii
Installation INSTALLING THECOOKTOP m [] [] m [] [] [] m [] [] [] m [] [] [] m [] [] [] m [] [] [] [] [] Place and center the cooktop within the cutout. Secure the cooktop to the countertop utilizing the two (2) 1/4-20 bolts provided. Do not overtighten the screws. CONNECTING THEGAS m m [] [] [] [] Attach the gas pressure inlet.
Installation GAS AND ELECTR(CREQU(REMENTS TABLE [] [] [] [] [] [] Bll [] [] [] [] [] [] [] [] Bll [] [] [] [] [] The required voltage, frequency and amperage ratings are listed on the product data plate outside on the cooktop bottom. The gas and electric requirements are also shown in the table below. ((((((((((((((((((((((((((((((((((((((((((((((((((((((((((((((((,_ iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii _ Model No.
Installation (NSTALUNGTHEBURNERCOMPONENTS [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] BurnerComponents Remove the brass burner rings, porcelain burner caps, and porcelain grates from their shipping packages. Place each burner ring onto its corresponding burner base, being certain that the four alignment tabs slide into the matching notches in the base. Set each porcelain burner cap on top of its corresponding burner ring.
Installation MAK(NGTHE ELECTR(CALCONNECT(ON [] [] [] [] [] [] [] [] [] [] [] Plug the three-prong plug from the appliance polarized wall receptacle.
Operation VER(FY(NG THE OPERAT(ON .............................................. m m [] [] [] Before beginning [] [] [] [] the test procedure, [] [] [] [] [] [] [] [] [] [] ensure that the gas supply is turned [] [] off at the shut-off valve, all cooktop control valves are in the "OFF" position, and all burner rings, burner caps, and grates are properly positioned on the cooktop. Rotate one knob at a time counterclockwise to the "LITE/Hr' position.
Operation Turn on the main gas supply to the cooktop by opening the gas shut-off valve. Test each burner separately by pressing and turning one control knob at a time counterclockwise to the "LITE/Hr' position. All ignitors will spark simultaneously. (It will take approximately four seconds for ignition to occur, at which time all igniters will stop sparking.
I Professional ICON series Liquid Petroleum Gas (LPG) Conversion Instructions Kit Cooktop Models: E36GC76EPS, E48GC76EPS Model E36GC76EPS shown ----_ WARNING: _ This conversion kit shall be installed by a qualified service agency in accordance with the manufacturer's instructions and all applicable codes and requirements of the authority having jurisdiction, If the information in these instructions is not followed exactly, a fire, explosion, or production of carbon monoxide may result causing prope
[] Electrolux I Ic o N Before converting to LPG, install the cooktop in the cabinet according to the installation instructions provided. LPG Conversion Kit for Models E36GC76EPS and Kit Part Number: Part Number E48GC76EPS (36 and 48-Inch) 700208-1 65480 Description LABEL, CONVERSION INFORMATION 86007 TOOL, REMOVAL, BURNER RING 100444 INSTALLATION INSTRUCTIONS r LPG CONVERSION KIT 76125* 92125-48 O-RING r BYPASS ORIFICE, BYPASS, .48 MM 92125-61 ORIFICE, BYPASS, .
Professional 3-1 If the cooktop is connected to a natural gas supply line, close the gas supply valve. 3-2 Disconnect the cooktop power connector from the electrical outlet. Series Cooktop LPG Conversion 3-3 Remove the grates from the top. 3-4 Remove all of the burner caps and burner rings from top of the burner heads.
[] Electrolux [ mc o N 4-1 Locate the regulator. It is underneath the cooktop, below the right rear burner. 4-2 Remove the regulator cap from the regulator. Make sure that the regulator spring remains in place.
Professional 5-1 Insert the large end of the burner ring removal toot into the top of the left rear burner head. Unscrew and remove the nut. 5-2 Remove the burner head, Slip the igniter wire off of the burner as you remove it. Removal toot Retaining nut Series Cooktop 5-3 Repeat steps 5-1 and 5-2 for the remaining burners. 5-4 Lift out the spill tray.
[] Electrolux [ Ic o N 6-1 6-2 Make sure all knobs are in the off position, Remove all of the burner knobs from the front of the burner location, The bypass orifice's size is stamped on its head, the cooktop, 6-ai 6-4 6-5 bypass orifice from the right side of the valve assembly, Insert the bypass orifice and the attached o-ring into the right side of the valve with the needle nose pliers. Tighten into place with the fiat-blade screwdriver. 6-6 Identify the appropriate bypass orifice from Table 6-1.
Professional 7-1 Remove the two screws that hold the left rear burner base to the chassis. 7-2 Hold the shutter connector with the 8" adjustable wrench. Remove the air shutter using the 6" adjustable wrench. 7-5 Check to make sure that the compression nut is tightened into the back of the shutter connector. 7-6 Repeat steps 7-1 through 7-5 for the remaining burners.
[] Electrolux [ ic o N I_'t / _ "Jl: -I 8-1 _:'_'1 D1 i iiI _i i_-!-I ! I iC_II 1_-_ !- Connect the U-tube manometer to the LPG 8-5 Make sure all knobs on the front of the cooktop are in the off position. supply line. 8-2 With electrical power to the cooktop disconnected, open the LPG supply valve. 8-6 Connect the U-tube manometer to the left rear burner's main orifice with 3/8" surgical tubing. 8-3 Verify that the pressure is above 11 inches water column (WC) and below 1/2PSI.
Professional Series Cooktop Burner E36GC76EPS E48GC76EPS Location Left Rear _36-Inch_ HN A-0053-E _48-Inch_ HN A-0053-E Left Front HN A-0052-E HN A-0052-E Right Rear HN A-0052-E HN A-0052-E Right Front Center Rear HN A-0053-E HN A-0053-E HN A-0053-E HN A-0053-E Center Front HN A-0053-E HN A-0053-E LPG Conversion i / Table 9-1 Air Shutter Burner E36GC76EPS E4BGC76EPS Location Left Rear _36-Inch) .38/9.7 _48-Inch) .39/9.8 Left Front .27/6.9 .12/3.1 Ric_ht Rear .29/7.4 .18/4.
[] Electrolux I Ic o N 10-1 Hake sure that all knobs on the front of the 10-4 cooktop are in the off position. 10-2 With electrical power to the cooktop disconnected, open the LPG supply valve. 10-3 Using a gas leak detector or bubble forming leak detection fluid, check the following for leaks: • LPG gas supply connection • All manifold connections Re-assemble the burner heads, burner head nuts, burner rings, and burner caps without the spill tray in place.
Professional Series Cooktop LPG Conversion Kit 12-1 Wait for all the burners to coot. 12-4 Install the spill tray. 12-2 Fill out and apply the conversion labels: 12-5 Replace the burner heads, burner head nuts, burner rings, and burner caps. Be sure the igniter wire is connected to the igniter for each burner head. • Apply one where it can be easily read on the floor of the chassis. • Apply the other near the rating label on the underside of the cooktop. 12-6 Install the cooktop grates.
If it is necessary to returnthe cooktopto naturalgasservice,repeatallofthe stepsin thisprocedure usingthe partsthat havebeenremoved.Usethe chartbelowto determine the orificesizes,shuttergaps,andthe air shutterpartnumbers. Natural Gas Conversion Specifications Burner Bypass Orifice Main Orifice Air Shutter Air Shutter Location Left Rear _X 100 mm) 81 _X 100 mm) 184 Part No. HN A-0053-E Gap .37/9.5 Left Front 72 135 HN A-0052-E .09/2.3 Ric_htRear 72 135 HN A-0052-E .09/2.