Zeppelinstrasse 19 D-82205 Gilching Fon +49-8105-778090 info@lcd-module.de http://www.lcd-module.de 1.2018 OLED 60.5x37.0mm - 128x64 DOTS Incl. Kontroller SSD1309Z FEATURES 2.42” LOW-POWER OLED -40..+80°C (TOP.) 128X64 DOTS INCL. CONTROLLER SSD1309Z SPI, I²C, 8-BIT INTERFACE FAST RESPONSE TIME (10µS) EVEN AT -40°C ZIFF CONNECTION 60.5X37.0MM OUTLINE DIM. ORDERING CODE OLED 2.42” - 128X64 DOTS, YELLOW ACCESSORY EA W128064-XALG ZIF CONNECTOR SMD 0.
Zeppelinstrasse 19 D-82205 Gilching Fon +49-8105-778090 info@lcd-module.de http://www.lcd-module.de Content 1.General Specification 2.Contour Drawing & Block Diagram 3.Interface Pin Function 4.Absolute Maximum Ratings 5.Electrical Characteristics 6.Optical Characteristics 7.OLED Lifetime 8.Reliability 9.Inspection specification 10.Precautions in use of OLED Modules 11.
Zeppelinstrasse 19 D-82205 Gilching Fon +49-8105-778090 http://www.lcd-module.de info@lcd-module.de 1. General Specification Item Dimension Unit 128 x 64 － 60.5 × 37.0 × 2.15 mm 55.01 × 27.49 mm Pixel Size 0.40 × 0.40 mm Pixel Pitch 0.43 × 0.
Zeppelinstrasse 19 D-82205 Gilching Fon +49-8105-778090 info@lcd-module.de http://www.lcd-module.de 2. Contour Drawing & Block Diagram 0.25 Dots 128*64 View Direction SYM BOL PIN NO. 1 NC(G ND) 17 D/C# 2 VSS 18 R/W # 3 NC 19 E/RD# 4 NC 20 D0 5 NC 21 D1 6 NC 22 D2 7 NC 23 D3 8 NC 24 D4 9 NC 25 D5 10 NC 26 D6 11 VDD 27 D7 12 BS1 28 IREF 13 BS2 29 VCOM H 14 NC 30 VCC 15 CS# 31 NC(G ND) 16 RES# 2.15¡ 0Ó.2 1.10¡ 0Ó.1 0.70¡ 0Ó.1 0.50¡ 0Ó.
Zeppelinstrasse 19 D-82205 Gilching Fon +49-8105-778090 info@lcd-module.de http://www.lcd-module.
Zeppelinstrasse 19 D-82205 Gilching Fon +49-8105-778090 info@lcd-module.de http://www.lcd-module.de 3. Interface Pin Function No. 1 Symbol Function NC(GND) No connection 2 VSS Ground. 3-10 NC No connection 11 VDD 12 BS1 13 BS2 14 NC 15 CS# 16 RES# 17 D/C# 18 R/W# EA W128064-XALG Power supply pin for core logic operation MCU bus interface selection pins. Select appropriate logic setting as described in the following table.
Zeppelinstrasse 19 D-82205 Gilching Fon +49-8105-778090 info@lcd-module.de http://www.lcd-module.de (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected. When serial or I2C interface is selected, this pin must be connected to VSS. This pin is MCU interface input. When 6800 interface mode is selected, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled HIGH and the chip is selected.
Zeppelinstrasse 19 D-82205 Gilching Fon +49-8105-778090 http://www.lcd-module.de info@lcd-module.de 4. Absolute Maximum Ratings Parameter Symbol Min Max Unit Notes Supply Voltage for Logic VDD -0.3 4 V 1, 2 Supply Voltage for Display VCC 0 15 V 1, 2 Operating Temperature TOP -40 +80 °C - TSTG -40 +80 °C - Storage Temperature Note 1: All the above voltages are on the basis of “VSS = 0V”.
Zeppelinstrasse 19 D-82205 Gilching Fon +49-8105-778090 info@lcd-module.de http://www.lcd-module.de 5. Electrical Characteristics Item Symbol Condition Min Typ Max Unit Supply Voltage for Logic VDD － 2.8 3.0 3.3 V Supply Voltage for Display VCC － 12 13 15 V High Level Input VIH Low Level Input VIL High Level Output VOH Low Level Output VOL 50% Check Board operating Current － － － － 0.8×VDD － 0.9×VDD － － － － － － 0.2×VDD － 0.1×VDD V V V V VCC =13.
Zeppelinstrasse 19 D-82205 Gilching Fon +49-8105-778090 info@lcd-module.de http://www.lcd-module.de 6. Optical Characteristics Item View Angle Contrast Ratio Response Time Symbol Condition Min Typ Max Unit (V)θ 160 deg (H)φ 160 deg CR Dark T rise － 10 μs T fall － 10 μs 70 90 cd/m2 Display with 50% check Board Brightness 2000:1 － CIEx(Yellow) (CIE1931) 0.45 0.47 0.49 CIEy(Yellow) (CIE1931) 0.48 0.50 0.
Zeppelinstrasse 19 D-82205 Gilching Fon +49-8105-778090 info@lcd-module.de http://www.lcd-module.de 7. OLED Lifetime ITEM Conditions Operating Life Time Ta=25℃ / Initial 50% check board brightness Typical Value Min Typ 50,000 Hrs － Remark Note Notes: 1. Life time is defined the amount of time when the luminance has decayed to <50% of the initial value. 2.
Zeppelinstrasse 19 D-82205 Gilching Fon +49-8105-778090 info@lcd-module.de http://www.lcd-module.de 8. Reliability Content of Reliability Test Environmental Test Test Item Content of Test Test Condition High Temperature storage Low Temperature storage Endurance test applying the high storage temperature for a long time. Endurance test applying the low storage temperature for a long time.
Zeppelinstrasse 19 D-82205 Gilching Fon +49-8105-778090 info@lcd-module.de http://www.lcd-module.de Test and measurement conditions 1. All measurements shall not be started until the specimens attain to temperature stability. After the completion of the described reliability test, the samples were left at room temperature for 2 hrs prior to conducting the failure test at 23±5°C; 55±15% RH. 2. All-pixels-on is used as operation test pattern. 3.
Zeppelinstrasse 19 D-82205 Gilching Fon +49-8105-778090 info@lcd-module.de http://www.lcd-module.de 9. Inspection specification NO 01 02 03 04 Item Electrical Testing Black or white spots on OLED (display only) OLED black spots, white spots, contamination (non-display) Polarizer bubbles EA W128064-XALG Criterion 1.1 Missing vertical, horizontal segment, segment contrast defect. 1.2 Missing character , dot or icon. 1.3 Display malfunction. 1.4 No function or no display. 1.
Zeppelinstrasse 19 NO 05 Item Scratches D-82205 Gilching Fon +49-8105-778090 info@lcd-module.de http://www.lcd-module.de Criterion Follow NO.3 OLED black spots, white spots, contamination Symbols Define: x: Chip length y: Chip width z: Chip thickness k: Seal width t: Glass thickness a: OLED side length L: Electrode pad length: AQL 6.1 General glass chip : 6.1.
Zeppelinstrasse 19 NO Item D-82205 Gilching Fon +49-8105-778090 Criterion Symbols : x: Chip length y: Chip width z: Chip thickness k: Seal width t: Glass thickness a: OLED side length L: Electrode pad length 6.2 Protrusion over terminal : 6.2.1 Chip on electrode pad : y: Chip width x: Chip length y≦0.5mm x≦1/8a 6.2.2 Non-conductive portion: 06 info@lcd-module.de http://www.lcd-module.de AQL z: Chip thickness 0 ＜ z≦t Glass crack 2.
Zeppelinstrasse 19 NO 07 08 09 10 11 Item Cracked glass Backlight elements D-82205 Gilching Fon +49-8105-778090 info@lcd-module.de http://www.lcd-module.de Criterion AQL The OLED with extensive crack is not acceptable. 2.5 8.1 Illumination source flickers when lit. 8.2 Spots or scratched that appear when lit must be judged. Using OLED spot, lines and contamination standards. 8.3 Backlight doesn’t light or color wrong. 0.65 2.5 0.65 Bezel 9.
Zeppelinstrasse 19 NO 12 D-82205 Gilching Fon +49-8105-778090 info@lcd-module.de http://www.lcd-module.de Item Criterion AQL 2.5 General appearance 12.1 No oxidation, contamination, curves or, bends on interface Pin (OLB) of TCP. 12.2 No cracks on interface pin (OLB) of TCP. 12.3 No contamination, solder residue or solder balls on product. 12.4 The IC on the TCP may not be damaged, circuits. 12.
Zeppelinstrasse 19 D-82205 Gilching Fon +49-8105-778090 Check Item Classification No Display Major info@lcd-module.de http://www.lcd-module.
Zeppelinstrasse 19 D-82205 Gilching Fon +49-8105-778090 info@lcd-module.de http://www.lcd-module.de 10. Precautions in use of OLED Modules Modules (1)Avoid applying excessive shocks to module or making any alterations or modifications to it. (2)Don’t make extra holes on the printed circuit board, modify its shape or change the components of OLED display module. (3)Don’t disassemble the OLED display module. (4)Don’t operate it above the absolute maximum rating.
Zeppelinstrasse 19 D-82205 Gilching Fon +49-8105-778090 info@lcd-module.de http://www.lcd-module.de not over bend the film with electrode pattern layouts. These stresses will influence the display performance. Also, secure sufficient rigidity for the outer cases. (7) Do not apply stress to the LSI chips and the surrounding molded sections. (8) Do not disassemble nor modify the OLED display module. (9) Do not apply input signals while the logic power is off.
Zeppelinstrasse 19 D-82205 Gilching Fon +49-8105-778090 info@lcd-module.de http://www.lcd-module.de (1) The absolute maximum ratings are the ratings which cannot be exceeded for OLED display module, and if these values are exceeded, panel damage may be happen. (2) To prevent occurrence of malfunctioning by noise, pay attention to satisfy the VIL and VIH specifications and, at the same time, to make the signal line cable as short as possible.
Zeppelinstrasse 19 D-82205 Gilching Fon +49-8105-778090 info@lcd-module.de http://www.lcd-module.de (6)Resistors, capacitors and other passive components will have different appearance and color caused by the different supplier. (7)Our company will has the right to upgrade and modify the product function.
Zeppelinstrasse 19 D-82205 Gilching Fon +49-8105-778090 info@lcd-module.de http://www.lcd-module.de 11.
