Use and Care Manual

ManualsBrandseLEDing ManualsKitchen160-Degree Outdoor Black Motion Activity Self-Contained LED Solar Light Security/Flood/Spot Light

Introduction and Intellectual property Rights Statement

Connecting the Battery before setting up

1. The battery has been pre-charged before shipping and the light is ready for use

2. Make sure the main switch is in the OFF position

3. Open the battery compartment cover on the back of the light and plug the battery into the connector and carefully make sure the plug

position is correct then replace the cover (Fig. 1-1)

4. Initially check the LED illuminator and battery by slowly moving the main switch to position A or B, it should light up, then turn the switch

back to OFF for installation

Mounting the Light Fixture

1. Choose a flat and stable mounting surface with maximum exposure to sunlight. Cut the mounting template from the back of the package

and use it to mark the two screw mounting holes. The screw mounting holes also have reference “Marks” on the light body. refer. Fig. 1(2)

2. For wood mounting surfaces: Drill the screws into the pre-marked locations and mount the unit on wall. For concrete/brick/stucco: Pre-drill

clearance holes using a 3/16" masonry bit. Insert the plastic anchors and screws. Then mount the unit on wall. This light can be mounted

horizontally in a high position to project light toward the ground or it can be mounted vertically to project light sideways onto walls, or gated areas.

3. This light fixture with integrated solar panel must be mounted in a non-obstructed position where it will receive an average of at least 4

hours daily of direct sunlight all year round. It requires a sturdy mounting location such as a building/house, fence, wall, patio, roof, under the

eaves, or secure pole e.g. Securely mounting this unit and self contained solar panel ensures that it will perform well in all weather conditions.

4. For Northern hemisphere installations this light fixture should be mounted with a Southerly facing position and visa-versa for Southern

hemisphere installation it should face to the North (Australia, South Africa, South America e. g.)

5. A small RED-LED indicator (under motion detector lens) will begin making a double flash indicating that charging status is active

during a normal sunny, partially sunny or cloudy day (If this does not make an indication that means the battery’s status is fully charged).

6. Open the left side cover (refer. Fig. 2) move the function switch to B position (recommended) to start the Initial Set-up or Walk test

procedure. Please refer to the 3 Mode-Selectable One step Set-up instructions and also refer to Page 2 for procedure details. Must

remove the protective film on top of the solar panel before using.

7. After the Initial Set-up test, if there is no motion during the testing delay time period (10 min.), the unit will enter into normal operation and

illuminate automatically only when the environment becomes dark.

Fig. 1 Installation Steps

Mount on the Two Screws

Connect

Li-Battery

before

operation

Mounting Mark Points for Setting

Reference as Option on light body

SMART-plus Solar Light built with 60 super bright LEDs

Model EE860plus User Manual

IMPORTANT …. Read this User Manual Before Installing...!!!

Initial Installation (Refer to Fig. 1)

Fig. 2 Functions

3 Mode-Selectable Set-up (Refer Fig-2 and PG 2 for more info, disregarding light plastic mark)

1. SMART B Profile/Mode (Max-bright adjustable)- This mode is recommended and

can be used for most illumination/lighting applications:

Set the Main Switch to B (downward position). Set the Left Dial between L--H for the

desired Max-brightness level above soft-glow illumination once activated by motion, (M--H

is recommended). Set the Right Dial between L to H (M to below H is recommended)

2. SMART A Profile/Mode (Soft-Glow Dimming brightness adjustable):

Set the Main Switch to A in the center position. Set the Left Dial between L--H for the

desired level of soft-glow illumination when motion is not detected, (L--M is

recommended). Set the Right Dial between L to H (M to below H is recommended)

3. SMART AUTO Profile/Mode (Motion activated lighting only):

Set the Main Switch to either A or B. Set the Left Dial to AUTO in the far left position.

Set the Right Dial between L to H (M to below H is recommended)

Fig. 1 (1)

Rev. EE860plus.072015 Page 1

Fig. 1(2)

Drill Screw Holes as per Instructions

Thank you for using the EE860plus light is upgraded dual operating SMART modes with outstanding performance and enhanced Li-Battery capacity. With

its effortless setup and lightweight design, the EE860plus LED Smart Light conforms to all your lighting needs. It was designed and built to provide many years of

trouble free service using environmentally friendly Solar-Hybrid-Lithium based energy technology. This product is covered under multiple US, European, China and

(WP)

(BP)

Summary of content (2 pages)

PAGE 1
® Na tu Model EE860plus User Manual re W hite Il lumi natio n SMART-plus Solar Light built with 60 super bright LEDs IMPORTANT …. Read this User Manual Before Installing...!!! (BP) (WP) Introduction and Intellectual property Rights Statement Thank you for using the EE860plus light is upgraded dual operating SMART modes with outstanding performance and enhanced Li-Battery capacity. With its effortless setup and lightweight design, the EE860plus LED Smart Light conforms to all your lighting needs.
PAGE 2
SMART AUTO Profile In either A or B position, if the Left Dial is set to Auto (turned all the way to the far left past “L” to the “Auto“ position) then this light will convert to operate as a traditional motion sensing light. In this SMART AUTO mode it will light up to full brightness when motion is detected.