D Betriebsanleitung Systemkreissäge G Operating Instruction System circular saw F Instructions d'utilisation Scie circuaire à système PK 255 0 5 10 15 20 25 30 35
D G F Deutschland Die beiliegende Garantiekarte senden Sie bitte an uns zurück. Den Kaufbeleg bitte aufbewahren! Ein Anspruch auf Garantieleistungen besteht nur gegen Vorlage des Kaufbelegs. Die Adresse Ihrer nächstgelegenen Werksvertretung finden Sie auf der hinteren Umschlagseite. 1. Great Britain Please return the enclosed warranty card to us. Retain proof of purchase! You are only entitled to claim warranty against proof of purchase.
XA0011E.fm 2Great Britain Scope of delivery 1 2 0 5 10 15 4 20 25 30 35 6 3 5 1 System circular saw with saw blade 2 Blade guard hardware bag 3 Rip fence with auxiliary fence extrusion 4 Push stick / feeding aid 5 Leg with foot (4x) 6 Connector suction hose / chip case PK 255 2.
Saw components and controls 3 4 2 5 1 0 5 10 15 20 25 30 35 6 7 8 9 10 1 Saw blade 2 Riving knife 3 Blade guard 4 Rip fence with auxiliary fence extrusion 5 Push stick / feeding aid 6 Handwheel with lock lever for blade tilt setting 7 Handwheel for depth of cut setting 8 On/off switch with emergency stop 9 Mains connection 10 Legs 2.
Please read first! · Read these instructions before commissioning. Pay special attention to the safety information. · If you notice a transport damage while unpacking, notify your supplier immediately. Do not operate the machine! · Dispose of the packing environmentally friendly. Bring to a proper collecting point. · Keep these instructions for reference on any issues you may be uncertain about. · If you lend or sell this machine be sure to have the instructions to go with it.
Symbols shown on the machine Safety devices A Danger! Disregard of the following warnings can lead to severe personal injury or material damage. Read instructions. Riving knife The riving knife prevents the workpiece from being caught by the rising teeth of the saw blade and being thrown against the operator. Always have riving knife installed during operation. Do not reach into the revolving saw blade. f Wear hearing protection. Use push stick if distance between saw blade and rip fence is £ 120 mm.
Operating controls On/off switch with emergency stop · To switch ON = press green button. · To switch OFF = press red button or cover of on/ off switch. Ratchet lock lever The set bevel angle can be locked with a ratchet lock lever, so it does not change during sawing. are several ratchet lock levers on the 3 There saw. If the swivelling range is not sufficient, the lever position can be shifted: pull lever up, turn and let engage again.
Rip fence The rip fence slides onto the saw from the righthand side and locks on the saw’s front. The auxiliary fence extrusion can be repositioned after loosening the two wing nuts: · small edge (as shown): - for cutting thin stock; - when the saw blade is tilted. · wide edge: - for cutting thick stock (max. 65 mm). Assembly and connection Installation of legs 1. Put a rubber foot on each of the four legs (on the side with the skewed corner). 2. Turn saw over and place on the saw table. 3.
Mitre fence 1. Screw long stud screw into centre tapped hole of the guide bar and tighten. 0 15 30 45 Dust collection from chip casing 1. Turn saw upside down. 2. Remove transport support inside the saw housing. 3. Attach suction port to chipcase with - 3 ea. hex. head screw M 6x13 - 3 ea. washer - 3 ea. serrated lock washer - 3 ea. hexagon nut M 6 45 using a dust collector, connect to 3 Iftheyouchiparecase's suction port. Dust collection from blade guard 1. Fit blade guard to riving knife.
Mains connection Operation Electrical Hazard B Danger! Operate saw in dry environment only. · Check the following for proper operation before starting work: - emergency stop switch; - riving knife; - blade guard; - push stick. · Use personal protection gear: - dust respirator; - hearing protection; - safety glasses. · Assume proper work position: - in front of the saw on the infeed side; - frontal to the saw; - to the left of the line of cut.
Rip cuts with rip fence Care and maintenance 1. Lock rip fence in required position on saw table. A Danger! Prior to all servicing: A Danger! Use push stick if distance between rip fence and saw blade is less than 120 mm. 0 - Switch machine OFF. - Unplug power cable. - Wait until the saw has come to a complete stop. · Check that all safety devices are operational again after each service. · Replace defective parts, especially of safety devices, only with genuine replacement parts.
6. To block the saw blade insert lock bar into hole in the saw table and turn saw blade by hand until lock bar engages in saw spindle hole. - Do not use loose-fitting reducing rings; the saw blade could work loose. - Saw blades have to be mounted in such way that they do not wobble or run out of balance, and can not work loose during operation. 11. Slide outer blade collar onto saw spindle. The saw spindle’s driving pin must fit into the pin hole of the outer blade collar. 12.
5. Turn saw over and place on its saw table. 6. Loosen the two nuts inside the saw by approx. one turn. 7. Stand saw back on its feet/workstand. 8. Adjust saw blade position by turning the setting nuts. 9. Turn saw over again and place on its saw table. 10. Tighten both nuts inside the saw again. 11. Stand saw on its feet/workstand again. 12. Loosen all setting nuts by approx. two turns. 13. Slide chip case cover back into the closed position and tighten screws. 14. Fasten removable table section.
1. Take blade guard off. 2. Remove the two fastening screws of the removable table section. 3. Raise blade fully. 4. Lift chip case cover slightly and swing to the side. The cover is hooked into the bottom of the chip case and can not fall down. 5. Loosen nut on riving knife by approx. one turn. 6. Adjust riving knife position. 7. Tighten nut. Blade tilt stop setting 1. Raise blade fully and set at true 90˚ against the table with the help of a try square. 2.
Universal fence adjustments Service plan Before switching ON - Chip ejection (when operated without dust collection) and - table slot Visual check if unobstructed by chips. Riving knife Visual check if distance saw blade – riving knife is 3...8 mm. Monthly (if used daily) 15 30 45 1. Check if fence is square against saw blade with a try square. 2. If necessary, loosen fixing screws and adjust mitre scale. - Remove chips with vacuum cleaner or brush; - apply light coat of oil to guide elements.
Troubleshooting A Danger! Before carrying out any fault service or maintenance work always: - Switch machine OFF. - Unplug power cable. - Wait for saw blade to come to standstill. Check that all safety devices are operational again after each fault service. Motor does not run Undervoltage relay Switch on again. tripped by power failure. No supply voltage. Check cables, plug, outlet and mains fuse. Motor overheated, e.g. by - a dull saw blade - too high a feed rate - sawdust build-up in housing.
Technical specifications Single-phase motor Three-phase motor Voltage V 230 (1~ 50 Hz) 400 (3~ 50 Hz) Rated current A 11.0 6.0 Fuse protection min. A 1 x 10 time-lag 3 x 16 time-lag IP 44 IP 44 min-1 2800 2800 kW kW 2.5 kW S6 40% 1.9 kW S6 40% 3.4 kW S6 40% 2.5 kW S6 40% min-1 3800 3800 Saw blade cutting speed m/s 50 50 Saw blade diameter (outer) mm 250 250 Saw blade arbor bore diameter (inner) mm 30 30 Depth of cut at 90˚ vertical at 45˚ tilt mm mm 0 ... 80 0 ...
Circuit diagrams Single-phase motor Three-phase motor 2.
Aktiengesellschaft Postfach 13 52, D-49703 Meppen EG-Konformitätserklärung - EC conformity declaration - Déclaration de conformité CEE EG-verklaring van overeenstemming - EF-overensstemmelsesattest - EG-konformitetsdeklaration EF-konformitetserklæring - Selvitys ey-standardinmukaisuudesta - Dichiarazione di conformità CE Declaración de conformidad-UE - Declaração de conformidade CE Wir erklären, daß die Bauart der Maschine/des Gerätes - We declare that the design of the machine/appliance Nous certifions qu
B Belgium Elektra Beckum Belgium N.V.S.A. Industriezone Hofte te Bollebeeklaan B-1730 Asse-Mollem Tel.: 0032-24540454 Fax: 0032-24540450 D Deutschland G I Elektra Beckum AG Daimlerstraße 1 D-49716 Meppen Tel.: 01803-333 456 Fax: 01803-333 457 K Danmark Elektra Beckum Danmark Lundeborgvej 9 Postbox 8113 DK-9220 Aalborg OE Tel.: 0045-98-151300 Fax: 0045-98-151451 E España France N H Suomi/ Finland Nofa OY P.O.Box 28 Hannuksentie 1 FIN-02270 Espoo Tel.
