Gebrauchsanweisung Geschirrspüler GI 3540
Inhalt Für den Bediener Für den Installateur Wichtige Hinweise 3 Gerätebeschreibung 4 Die Bedienungsblende 4 Vor dem Gebrauch Wasserenthärteranlage Klarspülmittel 6 6 8 Verwendung Ihres Geräts Geschirr einordnen Reinigerzugabe 9 9 11 Ratschläge für Spülen 12 Spülprogramme 13 Arbeitsschritte 14 Pflege und Reinigung Innenreinigung Reinigung der Siebe Außenreinigung Längerer Stillstand des Gerätes Frostgefahr Transport des Gerätes 16 16 16 17 17 17 17 Beseitigung von Funktionsstörungen Sich
Wichtige Hinweise Bewahren Sie diese Bedienungsanleitung sorgfältig zusammen mit dem Gerät auf, damit Sie sie auch in Zukunft zu Rate ziehen können. Sollten Sie das Gerät verkaufen oder Dritten überlassen oder es im Falle eines Umzuges in der alten Wohnung lassen, so sorgen Sie dafür, daß das Gerät komplett mit diesem Heft übergeben wird, damit der neue Besitzer sich über die Arbeitsweise des Gerätes und die diesbezüglichen Hinweise informieren kann.
Gerätebeschreibung 1. Geschirrkorbarretierung 2. Oberere Sprüharm 3. Salzbehälter 4. Behälter für Reiniger 5. Bedienblende 6. Behälter für Klarspüler 7. Siebe 8. Unterer Sprüharm 9. Oberer Geschirrkorb 10. Nivellierelemente IN137 Die Bedienungsblende 1. Betriebskontrollampe Die Kontrollampe leuchtet, wenn das Gerät am Stromnetz angeschlossen ist und die Ein/Aus-Taste gedrückt wird. Sie zeigt an, daß das Gerät betriebsbereits ist.
2. Taste "Ein/Aus" 6. Einschalten Nach dem Drücken dieser Taste leuchtet die Kontrollampe (1) und zeigt an, daß die Maschine unter Spannung steht und die Auswahl der Programme vorgenommen werden kann. Dies ist sehr praktisch und ökonomisch, wenn man nur wenig Geschirr spülen möchte. Halbe Menge können Sie zu jedem Spülprogramm, außer zu Vorspülen, hinzuwählen. Abschalten Wenn das Spülprogramm beendet ist, bleibt die Maschine automatisch stehen, die Kontrollampe (1) erlischt jedoch noch nicht.
Vor dem Gebrauch Vor der ersten Inbetriebnahme: 1. Sicherstellen, daß die Strom- und Wasseranschlüsse den Installationsanweisungen entsprechen. 2. Das Verpackungsmaterial aus dem Gerät nehmen. 3. Wasserenthärtungsanlage einstellen 4. Ein Liter Wasser in den Salzbehälter geben und mit Salz nachfüllen Stufe 5. Klarspüler einfüllen franz.
Einfüllen des regenerierenden Salzes Verwenden Sie ausschließlich Spezialsalz für Geschirrspülmaschinen. Sonstige Salzarten enthalten Anteile von anderen Stoffen, die auf die Dauer den Wasserenthärter beschädigen können. Das beim Einfüllen verschüttete Salz kann korrosionsfördernd sein. Deshalb sollte Salz erst kurz vor einem Programmstart eingefüllt werden (mit Ausnahme des Programms Kurzspülen). Einfüllen: 1.
Klarspülmittel Dieses Mittel macht das Geschirr glänzend und begünstigt dessen Trocknung. Es wird während des warmen Klarspülgangs automatisch eingegossen. Der im Inneren der Türe eingebaute Behälter hat ein Fassungsvermögen von ca. 110 ml Klarspülmittel, das je nach eingestellter Dosierung für 16 - 40 Spülgänge ausreicht. Einfüllen von Klarspülmittel 1. Den Behälter öffnen. Hierzu den Verschluß (A) nach links drehen. 2.
Verwendung Ihres Geräts Geschirr einordnen Vor dem Einordnen des Geschirrs in den Geschirrspülautomaten, sollten alle groben Speisereste entfernt werden, um Verstopfungen der Siebe zu vermeiden und eine gründliche Reinigung zu gewährleisten. Ordnen Sie keine kleinen Gegenstände ein, die durch die Körbe fallen könnten. Zum Einordnen des Geschirrs ziehen Sie die Geschirrkörbe heraus. UI51 Unterkorb Im unteren Geschirrkorb werden Töpfe, Deckel, Teller, Salatschüsseln, Besteck usw. eingeordnet.
Oberkorb Im Oberkorb werden Tassen, Gläser, Salatschüsseln, Untertassen, Dessertteller bis zu einem Durchmesser von 24 cm eingeordnet. Gläser mit langem Stiel können umgedreht in den höheren Tassenfächern eingehängt werden. Die linke Tassenauflage ist hochklappbar, damit z.B. hohe Gläser eineordnet werden können. In den oberen Geschirrkorb kommen vorzugsweise leichte Gegenstände, wie Plastikschüsseln usw. Beschweren Sie diese Teile mit anderen Geschirrteilen.
Reinigerzugabe Verwenden Sie ausschließlich spülmaschinengeeignete flüssige, pulveroder tablettenförmige Reinigungsmittel. Spülmittel einfüllen Min = 15 g Max = 30 g D Um das Spülmittelpulver zu verwenden, folgendermaßen vorgehen: 1. Sollte der Deckel des Behälters geschlossen sein, drücken Sie leicht den Verschlußhebel (D) nach hinten. M M IN AX 2. Die Reinigermenge ist abhängig vom Verschmutzungsgrad sowie der Menge des Geschirrs.
Ratschläge für Spülen So sparen Sie Energie Maschinenungeeignetes Geschirr: Legen Sie das benutzte Geschirr sofort in die Maschine. Das kann auch mehrmals geschehen, bis die Maschine voll beschickt ist.
Spülprogramme Programm Einzudrückende Taste(n) Programmbeschreibung Intensiv 70°C Stark verschmutzt. Geschirr, Besteck und Kochtöpfe Ein/Aus + Intensiv 70°C Vorspülen warm Hauptspülen 70°C 2 Klarspülgänge kalt 1 Klarspülgang warm Turbotrocknung Universal 65°C Normal verschmutzt. Geschirr und Besteck Ein/Aus + Universal 65°C Vorspülen lau Hauptspülen 65°C 1 Klarspülgänge kalt 1 Klarspülgang warm Turbotrocknung Leicht verschmutzt.
Arbeitsschritte 1. Prüfen Sie, ob die Siebe sauber sind 2. Prüfen Sie, ob Salz und Klarspülmittel vorhanden sind 3. Während des Programmablaufes wird ständig die aktuelle, noch verbleibende Laufzeit bis zum Programmende in Minuten angezeigt. 7a. Programm löschen Soll ein bereits gestartetes Programm gelöscht werden, so muß die Programmtaste des eingestellten Programms für 5 Sekunden gedrückt werden. Die Lampe neben der Taste geht aus, im Multidisplay werden drei waagerechte Striche angezeigt.
8. Programmende 9. Wenn im Multidisplay "000" erscheint ist das Programm beendet. Die Lampen der Programmablaufanzeige sind erloschen. Gerät durch Drücken der Taste Ein/Aus ausschalten. Vorsicht! Beim Öffnen der Tür, unmittelbar nach Programmende, kann heißer Dampf austreten. Tür vorsichtig öffnen. Lassen Sie am Programmende das Geschirr zum vollständigen Trocknen und Abkühlen noch 15 Minuten im geschlossenen Gerät.
Pflege und Reinigung Innenreinigung Reinigen Sie die Gummidichtungen der Türe und des Spül- bzw. Klarspülmittelbehälters mit einem feuchten Tuch. Nehmen Sie einmal jährlich, oder auch häufiger, ein Spülprogramm bei leerer Maschine, mit Zugabe von Spülmittel oder besser eines handelsüblichen Spezialproduktes für die Spülautomatenpflege vor. Reinigung der Siebe Die Siebe im Spülraumboden sind in hohem Grade selbstreingend. Trotzdem sollten diese gelegentlich kontrolliert und gereinigt werden.
Außenreinigung Die Bedienungsblende sollte regelmäßig mit einem weichen, feuchten Tuch gereinigt werden. Es dürfen nur neutrale Reinigungsmittel und keine Scheuermittel oder Lösungsmittel, wie Azeton, Trichloräthylen usw. verwendet werden. Längerer Stillstand des Gerätes Bei längerem Stillstand des Geschirrspülautomaten: 1. Stecker aus der Steckdose ziehen und Wasserhahn abdrehen. 2. Füllen Sie den Behälter für den Klarspüler. 3.
Beseitigung von Funktionsstörungen Wenn Ihr Geschirrspülautomat nicht funktioniert, liegt es oft nur an Wartungsfehlern oder sonstigen Kleinigkeiten, die Sie selbst einfach und rasch beheben können. Bevor Sie daher den Service-Dienst rufen, gehen Sie die folgende Liste von möglichen Fehlerquellen durch. Im Anzeigefeld werden die folgenden Alarme durch einen blinkenden Buchstaben (AL1, AL2, AL3, AL4, AL5, AL6, AL7, AL8) angezeigt.
Wenn die Funktionsstörung nach Überprüfung dieser Fehlerquellen nicht behoben werden kann, rufen Sie den nächsten autorisierten Kundendienst und geben Sie die Fehlerart, die Modellbezeichnung (Mod.), die Produktnummer (Prod. No.) und die Herstellnummer (Ser. No.) an. Sie können diese dem Typenschild des Geschirrspülautomaten entnehmen (siehe Abbildung). Sicherheitsvorrichtungen zum Schutz vor Überschwemmung Prod.No. ........ Ser. No. ......... Mod. ........
Garantieurkunde Für unsere Geräte übernehmen wir die Garantie zu den nachfolgend aufgeführten Bedingungen. 1. elektrabregenz gewährt eine Garantie von 12 Monaten, gerechnet vom Tag, der Lieferung an den Endverbraucher. Der Kaufbeleg dient als Nachweis. Diese Garantiezusage gilt nur gegenüber Endabnehmern, die Erstkäufer unserer Geräte vom Händler sind. 2.
Hinweise für Prüfinstitute Vor einer Prüfung muß der Salzbehälter des Entkalkers und der Spülmittelbehälter gefüllt werden. Prüfnorm: EN 50242 Vergleichsprogramm: Spar 50°C Beladung: 9 Maßgedecke Klarspülmittelwähler: Position 4 Reinigerdosierung: 20 g im Behälter 5 g auf dem Behälterdeckel Oberen Korb laden Unteren Korb laden Besteckkorb laden Technische Daten Abmessungen Breite Höhe max. Tiefe max.
Installationsanweisung Aufstellung Stellen Sie die Maschine in der Nähe eines Wasserzuund ablaufes auf. Sie sollten die beim Elektroanschluß des Gerätes anfallenden Arbeiten von einem fachkundigen und zugelassenen Elektriker ausführen lassen. Lassen Sie die beim Wasseranschluß des Gerätes entstehenden Arbeiten von einem fachkundigen und zugelassenen Installateur ausführen. Anschluß des Wasserzulaufschlauches Dieser Geschirrspülautomat ermöglicht einen Anschluß an Kalt- oder Warmwasser bis 60°C.
2 Ø Ø Der Wasserablaufschlauch kann angeschlossen werden: 18 21 1 min 4 cm Anschluß des Wasserablaufschlauches min 30 cm max 100 cm 1. am Syphonverschluß des Spülbeckens, mit einer Schlauchschelle; 2. an einem festen Wandanschluß mit Ablaufbelüftung, und mit einem Innendurchmesser von mindestens 4 cm. CS13 Knicke oder Quetschungen des Ablaufschlauches sind zu verhindern, da dies den Wasserablauf verlangsamen oder blockieren kann.
Elektra Bregenz Aktiengesellschaft Josef-Heiß-Straße 1 Postfach 150 A-6130 Schaw Telefon: 0 52 42/69 40-0 Hotline zum Ortstarif: Möbel/Sanitär: 0800/800 6305 Elektro: 0800/800 6304 Fax/Vertrieb Elektrofachhandel: 0 52 42/69 40-185 Möbelfachhandel: 0 52 42/69 40-186 Sanitärfachhandel: 0 52 42/69 40-186 Kundendienst 6900 Bregenz Brielgasse 27 Telefon: 0 55 74/64 500 Fax: 0 55 74/64 702 4020 Linz Fichenstraße 4 Telefon: 0 732/34 95 01 Fax: 0 732/33 00 93 6130 Schwaz Josef-Heiß-Straße 1 Telefon: 0 52 42/69