EN User Manual Refrigerator KS3320 KS3720
Contents Safety information Safety instructions Operation Daily Use Hints and tips 2 3 4 5 5 Care and cleaning Troubleshooting Technical information Installation 6 7 9 9 Subject to change without notice. Safety information Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible if an incorrect installation and use causes injuries and damages. Always keep the instructions with the appliance for future reference.
• • • • • • • • Do not use electrical appliances inside the food storage compartments of the appliance, unless they are of the type recommended by the manufacturer. Do not use water spray and steam to clean the appliance. Clean the appliance with a moist soft cloth. Only use neutral detergents. Do not use abrasive products, abrasive cleaning pads, solvents or metal objects. Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance.
Care and cleaning Use Warning! Risk of injury, burns, electrical shock or fire. • • • • • • • • Do not change the specification of this appliance. Do not put electrical appliances (e.g. ice cream makers) in the appliance unless they are stated applicable by the manufacturer. Be careful not to cause damage to the refrigerant circuit. It contains isobutane (R600a), a natural gas with a high level of environmental compatibility. This gas is flammable.
A medium setting is generally the most suitable. However, the exact setting should be chosen keeping in mind that the temperature inside the appliance depends on: • room temperature • how often the door is opened • the quantity of food stored • the location of the appliance. Daily Use Cleaning the interior Caution! Do not use detergents or abrasive products to prevent damage. 1. 2. Clean the inner side of the appliance and the accessories with warm water and neutral soap. Fully dry the appliance.
Hints for energy saving • • Do not open the door frequently or leave it open longer than absolutely necessary. If the ambient temperature is high and the Temperature Regulator is set to low temperature and the appliance is fully loaded, the compressor may run continuously, causing frost or ice on the evaporator. If this happens, set the Temperature Regulator toward warmer settings to allow automatic defrosting and so a saving in electricity consumption.
4. If accessible, clean the condenser and the compressor at the back of the appliance with a brush. This operation will improve the performance of the appliance and save electricity consumption. 1. 2. 3. 4. Defrosting of the refrigerator Frost is automatically eliminated from the evaporator of the refrigerator compartment every time the motor compressor stops, during normal use.
Problem Solution The lamp does not work. The lamp is defective. Refer to "Replacing the lamp". The compressor operates continually. Temperature is set incorrectly. Refer to "Operation" chapter. Many food products were put in at the same time. Wait some hours and then check the temperature again. The room temperature is too high. Refer to climate class chart on the rating plate. Food products placed in the appliance were too warm. Allow food products to cool to room temperature before storing.
If the advice does not lead to the desired result, call the nearest brand-mark service. 4. Closing the door 1. 2. 3. 3. Replace the bulb with one of the same power and specifically designed for household appliances (the maximum power is shown on the light unit) and with E14 socket type. Reconnect the appliance. Clean the door gaskets. If necessary, adjust the door. Refer to the assembly instructions. If necessary, replace the defective door gaskets. Contact the After Sales Service.
Location To ensure best performance, if the appliance is positioned below an overhanging wall unit, the minimum distance between the top of the cabinet and the wall unit must be at least 40 mm . Ideally, however, the appliance should not be positioned below overhanging wall units. Some models are fitted with a silencing pad under the cabinet. Do not remove this pad. Rear spacers Install the two spacers and the locking pins provided within the accessory bag as shown in the figure.
8. a1 a2 4. Unscrew the lower hinge. Change the position of the pin and buffer. Screw the lower hinge on the opposite side. 5. Tighten the pin with the adjustment spanner supplied. Raise the appliance and install the ventilation grille. Unscrew the handle. On the opposite side remove the hole covers by driving a 3-4 mm drift or drill into them. Install the handle. 6. 7. Install the hole covers provided within the accessory bag.
www.electrolux.