User Manual

14. GLOBAL SETTINGS MENU
58
TURBO SPEED press [YES] to start the turbo speed negotiation. Speed is chosen automatically. Please
note that you must use a MIDI interface that supports the Turbo-MIDI protocol.
OUT PORT FUNCTIONALITY selects what type of signal the MIDI OUT port will send.
• MIDI makes it possible for the port to send out MIDI data.
• DIN 24 will make the port send DIN 24 sync pulses. No MIDI data is sent on the port when this option
is selected.
• DIN 48 will make the port send DIN 48 sync pulses. No MIDI data is sent on the port when this option
is selected.
THRU PORT FUNCTIONALITY selects what type of signal the MIDI THRU port will send. The settings
are the same as for OUT PORT FUNCTIONALITY.
INPUT FROM selects the source Analog Rytm MKII will receive MIDI data from.
• DISABLED will make Analog Rytm MKII disregard any incoming MIDI data.
• MIDI will make Analog Rytm MKII listen only to MIDI data sent to the MIDI IN port.
• USB will make Analog Rytm MKII listen only to MIDI data sent to the USB port.
• MIDI+USB will make Analog Rytm MKII listen to MIDI data sent to both the MIDI IN and USB ports.
OUTPUT TO selects the destination to which Analog Rytm MKII will send MIDI data.
• DISABLED will stop Analog Rytm MKII from sending out any MIDI data.
• MIDI will make Analog Rytm MKII send MIDI data to the MIDI OUT port only.
• USB will make Analog Rytm MKII send MIDI data to the USB port only.
• MIDI+USB will make Analog Rytm MKII send MIDI data to both the MIDI OUT and USB ports.
• If MIDI+USB is selected in the INPUT FROM and/or OUTPUT TO settings, MIDI data
transfers will limit the USB speed. When sending or receiving large chunks of data,
make sure you use only the USB setting.
OUTPUT CH selects whether the [PADS] and the knobs will send data on the auto channel or the track
channel.
PARAM OUTPUT selects what type of MIDI messages the DATA ENTRY knobs will send. For information
about which CC/NRPN parameters that will be sent, please see “APPENDIX C: MIDI” on page 79.
• NRPN will make the knobs send out NRPN MIDI messages.
• CC will make the knobs send out CC MIDI messages.
ENCODER DEST controls whether the DATA ENTRY and TRACK LEVEL knobs will send MIDI data or
not. When set to INT, no MIDI data will be sent. When set to INT + EXT, MIDI will be sent internally as well
as externally.
PAD DEST controls whether the [PADS] will send MIDI data or not. When set to INT, no MIDI data will be
sent. When set to INT + EXT, MIDI will be sent internally as well as externally. When set to EXT, MIDI will
only be sent externally.
PRESSURE DEST controls whether varying pressure applied to the [PADS] will send MIDI data or not.
When set to INT, no MIDI data will be sent. When set to INT + EXT, MIDI will be sent internally as well as
externally. When set to EXT, MIDI will only be sent externally.
MUTE DEST controls whether activating/deactivating mutes will send MIDI data or not. When set to INT,
no MIDI data will be sent. When set to INT + EXT, MIDI will be sent internally as well as externally. When
set to EXT, MIDI will only be sent externally.
RECEIVE NOTES will when active, make it possible to play Analog Rytm MKII using an external MIDI
keyboard.
RECEIVE CC/NRPN will when active make it possible to control Analog Rytm MKII parameters from
an external MIDI device sending CC/NRPN data.
14.5.3 CHANNELS
This menu handles the MIDI channel configuration.