User Manual

ManualsBrandsElektron ManualsKeyboard SynthesizersDigitone Keys - 8 VOICE POLYPHONIC SYNTHESIZER

Table Of Contents

1. INTRODUCTION
- 1.1 CONVENTIONS IN THIS MANUAL
2. THE DIGITONE KEYS
3. PANEL LAYOUT AND CONNECTORS
- 3.1 FRONT PANEL
- 3.2 REAR CONNECTORS
- 3.3 SETTING UP AND STARTING THE DIGITONE KEYS
4. DIGITONE KEYS SOUND ARCHITECTURE
- 4.1 AUDIO VOICES
- 4.2 EFFECTS
5. OVERVIEW OF THE DIGITONE KEYS DATA STRUCTURE
- 5.1 +DRIVE
- 5.2 DATA STRUCTURE
- 5.3 ABOUT THE TRACKS
6. THE USER INTERFACE
- 6.1 SCREEN NAVIGATION
- 6.2 PARAMETER EDITING
- 6.3 QUICK SCROLLING
- 6.4 COPY, CLEAR, AND PASTE
- 6.5 THE NAMING SCREEN
  - 6.5.1 NAMING POP-UP MENU
- 6.6 HOLD
- 6.7 OVERBRIDGE
7. QUICK START
- 7.1 PLAYING THE FACTORY PRESET PATTERNS
- 7.2 CHANGING SOUNDS
- 7.3 USING MUTE MODE
- 7.4 TEMPO
- 7.5 EDITING PARAMETERS
8. DIGITONE KEYS CONTROLS
- 8.1 TRIG KEYS
- 8.2 ROTARY ENCODERS
- 8.3 PITCH AND MOD WHEELS
- 8.4 KEY BEHAVIOR
- 8.5 MIDI NOTES
- 8.6 MODES
9. PATTERNS AND SOUNDS
- 9.1 THE +DRIVE SOUND LIBRARY AND THE SOUND POOL
  - 9.1.1 ADDING SOUNDS TO THE SOUND POOL
- 9.2 PLAYING A SOUND
  - 9.2.1 PLAYING A SOUND WITH AN EXTERNAL MIDI UNIT
- 9.3 EDITING A SOUND
- 9.4 SAVING A SOUND
  - 9.4.1 SAVING A SOUND TO THE +DRIVE
  - 9.4.2 SAVING A SOUND TO THE SOUND POOL
- 9.5 SOUND SETUP MENU
- 9.6 ARPEGGIATOR MENU
10. THE SEQUENCER
- 10.1 BASIC PATTERN OPERATIONS
- 10.2 CREATING AND EDITING A PATTERN
- 10.3 TRIG PARAMETERS
- 10.4 TRACK NOTE MENU
- 10.5 VOICE MENU
- 10.6 MICRO TIMING MENU
- 10.7 PATTERN MENU
- 10.8 METRONOME MENU
- 10.9 SCALE MENU
  - 10.9.1 LENGTH PER PATTERN MODE
  - 10.9.2 LENGTH PER TRACK MODE
- 10.10 SEQUENCER FEATURES
- 10.11 CHAINS
  - 10.11.1 CREATING A CHAIN
11. SYNTH TRACK PARAMETERS
- 11.1 EDITING THE SYNTH TRACK PARAMETERS
- 11.2 TRIG PARAMETERS PAGE
- 11.3 SYN1 PAGE 1
- 11.4 SYN 2 PAGE 1
- 11.5 SYN2 PAGE 2
- 11.6 FLTR PAGE 1
- 11.7 FLTR PAGE 2
- 11.8 AMP PAGE 1
- 11.9 AMP PAGE 2
- 11.10 LFO PAGE 1
- 11.11 LFO PAGE 2
12. MIDI TRACK PARAMETERS
- 12.1 EDITING THE MIDI TRACK PARAMETERS
- 12.2 TRIG PARAMETERS PAGE
- 12.3 SYN1 PAGE (MIDI SOURCE)
- 12.4 SYN2 PAGE (MIDI SOURCE)
- 12.5 FLTR PAGE (CC VALUE)
- 12.6 AMP PAGE (CC SELECT)
- 12.7 LFO PAGE
13. FX PARAMETERS
- 13.1 EDITING THE FX PARAMETERS
- 13.2 CHORUS
- 13.3 DELAY
- 13.4 REVERB
- 13.5 MASTER
14. GLOBAL SETTINGS
- 14.1 PROJECT
- 14.2 SOUNDS
- 14.3 MIDI CONFIG
- 14.4 SYSEX DUMP
  - 14.4.1 SYSEX SEND
  - 14.4.2 SYSEX RECEIVE
- 14.5 AUDIO ROUTING (GLOBAL)
  - 14.5.1 ROUTE TO MAIN
  - 14.5.2 SEND TO FX
- 14.6 SYSTEM
- 14.7 CONTROL INPUT A
- 14.8 CONTROL INPUT B
- 14.9 MULTI MAP EDIT
  - 14.9.1 MULTI MAP MENU
15. STARTUP MENU
- 15.1 TEST MODE
- 15.2 EMPTY RESET
- 15.3 FACTORY RESET
- 15.4 OS UPGRADE
- 15.5 EXIT
16. SETUP EXAMPLES
- 16.1 DIGITONE KEYS WITH A MONOPHONIC BASS MACHINE
- 16.2 DIGITONE KEYS TOGETHER WITH THE DIGITAKT
- 16.3 CONTROLLING A SYNTHESIZER USING THE MIDI TRACKS
17. USEFUL KEY COMBINATIONS
18. TECHNICAL INFORMATION
19. CREDITS AND CONTACT INFORMATION
APPENDIX A: THE DIGITONE KEYS FM SYNTHESIS
- A.1 OVERVIEW
- A.2 THE OPERATORS
- A.3 ALGORITHMS
- A.4 FM RATIOS
- A.5 THE OPERATOR ENVELOPES
- A.6 HARMONICS
- A.7 SYN1 PAGE 1 PARAMETERS OVERVIEW
APPENDIX B: MIDI IMPLEMENTATION
- B.1 TRACK PARAMETERS
- B.2 TRIG PARAMETERS
- B.3 FM PARAMETERS
- B.4 FILTER PARAMETERS
- B.5 AMP PARAMETERS
- B.6 LFO PARAMETERS
- B.7 MIDI TRACK PARAMETERS
- B.8 FX PARAMETERS
- B.9 MISC PARAMETERS
APPENDIX C: LFO MODULATION DESTINATIONS
INDEX

6. THE USER INTERFACE

6.2.2 CONTROL ALL

If you press and hold [MIDI] and change a parameter setting, this change aects this parameter in all the

synth tracks in the pattern. Press [NO] before you release [MIDI] to revert the parameter changes.

6.2.3 [FUNC] KEY PRESS COMBINATIONS

The standard way to use the [FUNC] key in combination with other keys is to press and hold [FUNC] and

then press the second key in the combination. For some key combinations, it is also possible to access a

sub-menu by pressing and holding [FUNC] + second key for a second.

6.3 QUICK SCROLLING

Scroll through menus using the LEVEL/DATA knob. Quick scrolling is possible on many menus. Press

[FUNC] + the [UP] or [DOWN] keys to move the cursor one menu page.

6.4 COPY, CLEAR, AND PASTE

Copy, clear and paste commands are available in many contexts. Press [FUNC] + [RECORD] to copy. Press

[FUNC] + [STOP] to paste. Press [FUNC] + [PLAY] to clear. Repeat the key press combination to undo the

paste and clear operations. Please see the dierent sections in the manual for more information on when

these commands are available.

The copy clipboard can only hold one item at a time. When you perform a copy command,

the item copied replaces any earlier copied items. For example, you can not have both a

trig and a pattern copied at the same time.

6.5 THE NAMING SCREEN

The naming method is identical for the various naming situations that appear when you save sounds,

projects et cetera.

The [LEFT] and [RIGHT] arrow keys are used to navigate between the characters. Turning the LEVEL/

DATA knob or pressing the [UP] or [DOWN] arrow keys selects the characters. [FUNC] + [NO] erases

letters. [FUNC] + [YES] inserts space.

6.5.1 NAMING POP-UP MENU

A convenient way of naming is to open a pop-up menu that shows all available letters, symbols, and

digits. Press and hold the [FUNC] key when you are on the NAMING screen to access the NAMING

POP-UP menu.

Keep [FUNC] pressed and use the [ARROW] keys to highlight the character you want to insert. Once

there, release [FUNC] to add the character.

Copy, paste, and clear commands are available on the NAMING screen.