User Manual

ManualsBrandsElektron ManualsKeyboard SynthesizersDigitone Keys - 8 VOICE POLYPHONIC SYNTHESIZER

Table Of Contents

1. INTRODUCTION
- 1.1 CONVENTIONS IN THIS MANUAL
2. THE DIGITONE KEYS
3. PANEL LAYOUT AND CONNECTORS
- 3.1 FRONT PANEL
- 3.2 REAR CONNECTORS
- 3.3 SETTING UP AND STARTING THE DIGITONE KEYS
4. DIGITONE KEYS SOUND ARCHITECTURE
- 4.1 AUDIO VOICES
- 4.2 EFFECTS
5. OVERVIEW OF THE DIGITONE KEYS DATA STRUCTURE
- 5.1 +DRIVE
- 5.2 DATA STRUCTURE
- 5.3 ABOUT THE TRACKS
6. THE USER INTERFACE
- 6.1 SCREEN NAVIGATION
- 6.2 PARAMETER EDITING
- 6.3 QUICK SCROLLING
- 6.4 COPY, CLEAR, AND PASTE
- 6.5 THE NAMING SCREEN
  - 6.5.1 NAMING POP-UP MENU
- 6.6 HOLD
- 6.7 OVERBRIDGE
7. QUICK START
- 7.1 PLAYING THE FACTORY PRESET PATTERNS
- 7.2 CHANGING SOUNDS
- 7.3 USING MUTE MODE
- 7.4 TEMPO
- 7.5 EDITING PARAMETERS
8. DIGITONE KEYS CONTROLS
- 8.1 TRIG KEYS
- 8.2 ROTARY ENCODERS
- 8.3 PITCH AND MOD WHEELS
- 8.4 KEY BEHAVIOR
- 8.5 MIDI NOTES
- 8.6 MODES
9. PATTERNS AND SOUNDS
- 9.1 THE +DRIVE SOUND LIBRARY AND THE SOUND POOL
  - 9.1.1 ADDING SOUNDS TO THE SOUND POOL
- 9.2 PLAYING A SOUND
  - 9.2.1 PLAYING A SOUND WITH AN EXTERNAL MIDI UNIT
- 9.3 EDITING A SOUND
- 9.4 SAVING A SOUND
  - 9.4.1 SAVING A SOUND TO THE +DRIVE
  - 9.4.2 SAVING A SOUND TO THE SOUND POOL
- 9.5 SOUND SETUP MENU
- 9.6 ARPEGGIATOR MENU
10. THE SEQUENCER
- 10.1 BASIC PATTERN OPERATIONS
- 10.2 CREATING AND EDITING A PATTERN
- 10.3 TRIG PARAMETERS
- 10.4 TRACK NOTE MENU
- 10.5 VOICE MENU
- 10.6 MICRO TIMING MENU
- 10.7 PATTERN MENU
- 10.8 METRONOME MENU
- 10.9 SCALE MENU
  - 10.9.1 LENGTH PER PATTERN MODE
  - 10.9.2 LENGTH PER TRACK MODE
- 10.10 SEQUENCER FEATURES
- 10.11 CHAINS
  - 10.11.1 CREATING A CHAIN
11. SYNTH TRACK PARAMETERS
- 11.1 EDITING THE SYNTH TRACK PARAMETERS
- 11.2 TRIG PARAMETERS PAGE
- 11.3 SYN1 PAGE 1
- 11.4 SYN 2 PAGE 1
- 11.5 SYN2 PAGE 2
- 11.6 FLTR PAGE 1
- 11.7 FLTR PAGE 2
- 11.8 AMP PAGE 1
- 11.9 AMP PAGE 2
- 11.10 LFO PAGE 1
- 11.11 LFO PAGE 2
12. MIDI TRACK PARAMETERS
- 12.1 EDITING THE MIDI TRACK PARAMETERS
- 12.2 TRIG PARAMETERS PAGE
- 12.3 SYN1 PAGE (MIDI SOURCE)
- 12.4 SYN2 PAGE (MIDI SOURCE)
- 12.5 FLTR PAGE (CC VALUE)
- 12.6 AMP PAGE (CC SELECT)
- 12.7 LFO PAGE
13. FX PARAMETERS
- 13.1 EDITING THE FX PARAMETERS
- 13.2 CHORUS
- 13.3 DELAY
- 13.4 REVERB
- 13.5 MASTER
14. GLOBAL SETTINGS
- 14.1 PROJECT
- 14.2 SOUNDS
- 14.3 MIDI CONFIG
- 14.4 SYSEX DUMP
  - 14.4.1 SYSEX SEND
  - 14.4.2 SYSEX RECEIVE
- 14.5 AUDIO ROUTING (GLOBAL)
  - 14.5.1 ROUTE TO MAIN
  - 14.5.2 SEND TO FX
- 14.6 SYSTEM
- 14.7 CONTROL INPUT A
- 14.8 CONTROL INPUT B
- 14.9 MULTI MAP EDIT
  - 14.9.1 MULTI MAP MENU
15. STARTUP MENU
- 15.1 TEST MODE
- 15.2 EMPTY RESET
- 15.3 FACTORY RESET
- 15.4 OS UPGRADE
- 15.5 EXIT
16. SETUP EXAMPLES
- 16.1 DIGITONE KEYS WITH A MONOPHONIC BASS MACHINE
- 16.2 DIGITONE KEYS TOGETHER WITH THE DIGITAKT
- 16.3 CONTROLLING A SYNTHESIZER USING THE MIDI TRACKS
17. USEFUL KEY COMBINATIONS
18. TECHNICAL INFORMATION
19. CREDITS AND CONTACT INFORMATION
APPENDIX A: THE DIGITONE KEYS FM SYNTHESIS
- A.1 OVERVIEW
- A.2 THE OPERATORS
- A.3 ALGORITHMS
- A.4 FM RATIOS
- A.5 THE OPERATOR ENVELOPES
- A.6 HARMONICS
- A.7 SYN1 PAGE 1 PARAMETERS OVERVIEW
APPENDIX B: MIDI IMPLEMENTATION
- B.1 TRACK PARAMETERS
- B.2 TRIG PARAMETERS
- B.3 FM PARAMETERS
- B.4 FILTER PARAMETERS
- B.5 AMP PARAMETERS
- B.6 LFO PARAMETERS
- B.7 MIDI TRACK PARAMETERS
- B.8 FX PARAMETERS
- B.9 MISC PARAMETERS
APPENDIX C: LFO MODULATION DESTINATIONS
INDEX

10. THE SEQUENCER

10.7 PATTERN MENU

Use the PATTERN menu to perform pattern management. Press [PATTERN MENU] to open the menu.

Use the [UP] and [DOWN] arrow keys to move between the options. Press [YES] to conﬁrm your selection.

Press [NO] to exit the menu.

10.7.1 QUANTIZE

The quantization aects all micro timed and o grid trigs on the sequencers tracks. Change settings with

DATA ENTRY knob E and F.

TRK. aects the trigs of the active track in real time. The higher the quantize value, the more the trigs

are quantized. Press [T1–4] key to select what track to quantize. (0–127)

GLOBAL aects the trigs of all tracks in real time. The higher the quantize value, the more the trigs are

quantized. (0–127)

Press [NO] to exit the menu.

10.7.2 RENAME

Opens a NAMING screen where you can rename the active pattern.

10.7.3 CLEAR

WHOLE PATTERN Clears the active pattern’s sequencer and Sounds data. A prompt appears when

you select this option. Press [YES] to clear, or [NO] to cancel the operation. Note that you do not lose

any pattern information permanently until you save the pattern to the same pattern slot.

SOUNDS DATA Clears the active patterns four Sounds. All sequencer data will remain unchanged. A

prompt appears when you select this option. Press [YES] to clear, or [NO] to cancel the operation.

Note that until you save the pattern to the same pattern slot that you loaded from, you do not lose any

Sound information permanently.

SEQUENCE DATA Clears the active pattern’s sequence data. All sounds remain unchanged. A prompt

appears when you select this option. Press [YES] to clear, or [NO] to cancel the operation. Note that

until you save the pattern to the same pattern slot that you loaded from, you do not lose any sequenc-

er information permanently.

10.7.4 SAVE TO PROJ

You must have saved the project at least once before you can save pattern information.

WHOLE PATTERN Saves the active pattern’s sequence data and four Sounds to the +Drive. A prompt

appears when you select this option. Press [YES] to save, or [NO] to cancel the operation.

SOUNDS DATA Saves the active pattern’s four Sounds to the +Drive. A prompt appears when you

select this option. Press [YES] to save, or [NO] to cancel the operation.

SEQUENCE DATA Saves the active pattern’s sequence data to the +Drive. A prompt appears when

you select this option. Press [YES] to save, or [NO] to cancel the operation.

For more information, please see “10.10.7 TEMPORARY SAVE AND RELOAD PATTERN COMMANDS” on

page 43.