Owner manual

-24-
r Feed the battery snap wires through the slot on
the top case as shown in Figure U.
r Connect the battery and place it in the cavity of
the top case as shown in Figure V.
r Place the battery cover onto the case as shown
in Figure V. Hold the two sections together with
two M3 x 17.5 screws.
FINAL ASSEMBLY (continued)
Figure V
M3 x 17.5 Screws
Battery Cover
Battery
Figure U
Battery Snap Wires Slot
Assembled PC Board (Back View) Assembled PC Board (Front View)
-11-
ASSEMBLE THE FOLLOWING COMPONENTS TO THE PC BOARD
In all of the following steps the components must be installed either on the top or bottom legend sides of
the PC board as indicated. The board is turned to solder the component leads on the opposite side
(installed on Bottom, soldered on Top, installed on Top, soldered on Bottom).
Figure D
Lay resistor flat against the
PC board.
R8 - 470kΩ 5% 1/4W Res.
(yellow-violet-yellow-gold)
(see Figure A)
C6 - 22μF Lytic Capacitor
(see Figure B)
R4 - 100kΩ 5% 1/4W Res.
(brown-black-yellow-gold)
(see Figure A)
C5 - 100pF (101) Discap
R3 - 200kΩ 5% 1/4W Res.
(red-black-yellow-gold)
(see Figure A)
C4 - .1μF (104) Mylar Cap.
(small yellow)
C3 - .1μF (104) Mylar Cap.
(small yellow)
R2 - 1MΩ 5% 1/4W Res.
(brown-black-green-gold)
(see Figure A)
Figure A
Stand resistor on end as
shown. Solder and cut off
the excess leads.
White marking
on PC board
Figure B
Mount the capacitor with the negative (–)
lead in the negative hole and the positive
(+) lead in the positive hole marked on the
PC board. Mount the capacitor flat against
the PC board as shown.
Figure C
Mount the transistor
with the flat side in the
same direction as the
PC board marking.
Marking
on PC board
Flat
Side
Negative (–)
marking on
PC board
Negative (–)
marking on
capacitor
R7 - 470kΩ 5% 1/4W Res.
(yellow-violet-yellow-gold)
(see Figure A)
T1 - 2SC9013 Transistor
(see Figure C)
R5 - 100kΩ 5% 1/4W Res.
(brown-black-yellow-gold)
(see Figure D)
R6 - 1MΩ 5% 1/4W Res.
(brown-black-green-gold)
(see Figure A)
R9 - 470kΩ 5% 1/4W Res.
(yellow-violet-yellow-gold)
(see Figure A)
C1 - .1μF (104) Mylar Cap.
(large brown)
R1 - 220kΩ 5% 1/4W Res.
(red-red-yellow-gold)
(see Figure A)
C2 - .1μF (104) Mylar Cap.
(small yellow)
Figure E
Insert the switch into the
PC board in the location
shown. Make sure that
the notch on the switch
is in the same direction
as the marking on the
PC board.
Insert the 9V battery
wires through the hole of
the PC board as shown.
Solder and cut off the
excess leads.
Black Wire
Red Wire
Top Legend Side
Bottom Legend Side
Mount switch in direction shown.
Notch
SW1 - Switch On/Off
(see Figure E)
BATT - 9V Battery Snap
(see Figure E)
Assembled View