Installation Instructions

ManualsBrandselero GmbH Antriebstechnik ManualsElectronicsTubular Motor with Electronic Limit Switch

Symbol Signal

word

Description

NOTE This symbol warns of po-

tential property damage.

IMPOR-

TANT

This symbol indicates

important facts and con-

ditions as well as further

information in these

operating and installation

instructions. Additionally,

it refers to certain inst-

ructions giving additional

information or helping you

to perform a task.

Fig. 3 Notation of property damage and additional informa-

tion

The following example illustrates the general layout of a

safety instruction:

SIGNAL WORD

Type and source of danger

Description of the type and source of danger

►Measures for prevention of the danger.

3.3 General safety principles

The product was designed according to the state-of-the-art

and recognized safety-related rules and is safe for opera-

tion. During product design, basic safety and health requi-

rements of applicable laws, standards and guidelines were

observed. The safety of the product is conﬁ rmed by the EC

Declaration of Conformity.

All information on safety refer to currently applicable direc-

tives of the European Union. Operators in other countries

must ensure that applicable local laws and regulations are

observed.

Apart from the safety instructions in these operating inst-

ructions, generally applicable regulations on prevention of

accidents and environmental protection must be observed.

The product must only be used in technically ﬂ awless condi-

tion and for proper safety-conscious and risk-conscious use

while observing the operating instructions. The product is

designed for operation according to section „intended use“.

Operation of the product not according to its intended use

may lead to danger for life and limb of the user and third

parties or cause damage to the machine and other proper-

ties. The manufacturer must be immediately and directly in-

formed on accidents or near misses during operation of the

product that caused or may have caused personal injuries

and or damage to the working environment.

All safety instructions in the operating instructions and on

the product must be observed. Additionally to observing

these safety instructions, the operator must ensure that

all national and international regulations applicable in the

country of operation and other binding regulations on ope-

rational safety, prevention of accidents and environmental

protection are complied with. All work on the product must

only performed by trained, safety-related instructed and

authorized personnel.

Appropriately qualiﬁ ed personnel must observe all appli-

cable standards and regulations in the country of installation

and inform the customer on the operating and maintenance

requirements of the product.

3.4 General obligations of the operator

 The operator is obliged to only operate the product in

technically ﬂ awless and operationally safe condition. The

operator must ensure that apart from the safety instruc-

tions in the operating instructions, generally applicable

regulations on safety and prevention of accidents, the

provisions of DIN VDE 0100 as well as the regulations

on environmental protection of the respective country of

operation are observed and complied with.

 The operator is obliged to ensure that all work on the pro-

duct is carried out by trained and safety-related instructed

and authorized personnel.

 Ultimately responsible for accident-free operation is the

operator of the product or the personnel authorized by

him.

 The operator is responsible for compliance of the tech-

nical speciﬁ cations particularly the statistic and dynamic

load limits.

Non-compliance with static load limits may lead to

loss of the supporting or holding function.

 With respect to the intended use, the operator must ensu-

re dry, not too warm ambient conditions (building condi-

tions) under the inﬂ uence of radial heat. Deviations must

be approved by the manufacturer.

3.5 General requirements on personnel

 Each person commissioned to work with the product

must have read and understood the entire operating

instructions prior to carrying out the respective work. This

does also apply if the person has already worked with

this kind of product or was trained on it.

 Before start of all work, the personnel has to be made

aware of all dangers in connection with working on the

product.

 All personnel commissioned to work with the product

must have no physical limitations temporarily or perma-

nently inﬂ uencing their attention or good judgment (e. g.

by fatigue).

 Handling the product or any assembly, disassembly and

cleaning by minors or under the inﬂ uence of alcohol,

drugs or medication is not permitted.

 Personnel must wear appropriate personal protective

equipment according to the work to be carried out and

the present work environment.

 Children must not play with ﬁ xed control panels. Keep

remote controls away from children.

 Observe moving roller shutters and keep persons on a

distance until the shutter has properly closed.

3.6 Safety instructions on technical condition

 Prior to installation the product must be checked for

damage and proper condition.

 The operator is obliged to only operate the product in

technically ﬂ awless and operationally safe condition. The

technical condition must comply with statutory require-

ments applicable at the date of manufacturing stated on

the name plate.

 If dangers for personnel or changes in the operational

behavior are identiﬁ ed, the product must be put out of

operation immediately and the operator must be informed

on the incident.

 Without approval by the manufacturer, no modiﬁ cation,

extensions or alterations must be carried out on the

product.

Safety