User's Manual

5.7 Transmitter programming
Important
Requirement: The drive system must be in wireless opera-
tion.
►If the end positions are not programmed, the fabric is
loosened from the winding shaft.
Programming the (fi rst) transmitter
Instruction Result
1
Disconnecting and recon-
necting the power supply
For approx. 5 minutes,
the drive system is in
programming mode.
2
On the transmitter to be
programmed, press the
programming button P for
approx. 1 second.
The status indicator
fl ashes. Now (for
approx. 2 minutes),
the drive system is in
programming mode
(up and down move-
ment).
3
Immediately (max. 1 se-
cond) after start of the up
movement, press the UP
button ▲.
The status indicator
fl ashes briefl y. The
fabric stops briefl y,
moves on, stops and
moves downwards.
4
Immediately (max. 1 se-
cond) after start of the
down movement, press the
DOWN button ▼.
The status indicator
fl ashes briefl y. The
drive system stops.
The (fi rst) transmitter is programmed.
5.8 Programming additional transmitters(s)
A maximum of 16 transmitters can be programmed.
Programming additional transmitters(s)
Instruction Result
1
For three seconds, on a
already programmed trans-
mitter press simultaneously
for 3 seconds
the UPbutton ▲,
the DOWNbutton ▼ and
the programming button P.
The status indicator
fl ashes. The drive sys-
tem is in programming
mode (up and down
movement).
(alternative to above line)
Disconnecting and recon-
necting the power supply
For approx. 5 minutes,
the drive system is in
programming mode.
2
On the (additional)
transmitter to be program-
med, press the program-
ming button P.
The status indicator
fl ashes briefl y. The
drive system is (for
approx. 2 minutes) in
programming mode
(up and down move-
ment).
4
On the (additional)
transmitter to be program-
med, immediately (max. 1
second) after start of the up
movement, press the UP
button ▲.
The status indicator
fl ashes briefl y. The
fabric stops briefl y,
moves on, stops and
moves downwards.
5
On the (additionally)
transmitter to be program-
med, immediately (max.
1 second) after start of a
down movement, press the
DOWNbutton ▼.
The status indicator
fl ashes briefl y. The
drive system stops.
Programming of the additional transmitter is complete.
Stopping the bidirectional wireless programming mode:
Press the STOP button for at least 6 seconds until the sta-
tus indicator is blinking (transmitter-dependent).
Important
Complete, uninterrupted up and down movement is neces-
sary to adapt the fabric protection system to the fabric.
5.9 Technical data
The separately available „technical data sheet“ will provide
you with an overview of the most important technical para-
meters.
6 Troubleshooting
Problem /
malfunction
Possible
cause
Remedy,
correction
• Drive system
stops during
movement
• End positions
not correctly
set
• Drive system is
in setting mode
• Set end posi-
tions
• Drive system
stops after a
short period of
time
• End positions
have been
saved
• Stiff fabric
• Set second
end position
• Check smooth
running of the
fabric
• Drive system
only runs in
one direction
• Connection
error
• Check connec-
tion
• Drive system
does not react
• No power
supply
• Temperature
limiter has
triggered
• Check power
supply
• Have the drive
system cool
down
• Program-
ming of end
positions not
possible
• Random drive
movements
• The distance
to the end
position or to
the limit stop is
too short
• Delete end
positions
Reset end
positions
• The drive sys-
tem must run,
stop briefl y
and start again
(as long as a
button on the
elero installa-
tion cable or a
programmed
transmitter is
pressed).
Fig. 13 RolTop-915 troubleshooting
7 Servicing
The RolTop-915 is maintenance-free.
8 Cleaning
WARNING
Risk of injury due to electricity.
Risk of electric shock.
►Risk due to potential live parts.
►Only carry out cleaning when the system is disconnected
from the voltage. To do so, disconnect the drive cable.
►Clean the product surface only with a soft, clean and dry
cloth.
© elero GmbH US+CA | 9
Transmitter programming | Troubleshooting