JAN06.
E page 2 F page 21 S page 41 APPROVED FOR RESIDENTIAL APPLIANCES FOR RESIDENTIAL USE ONLY READ AND SAVE THESE INSTRUCTIONS PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING. INSTALLATION MUST COMPLY WITH ALL LOCAL CODES. IMPORTANT: Save these Instructions for the Local Electrical Inspectors use. INSTALLER: Please leave these Instructions with this unit for the owner. OWNER: Please retain these instructions for future reference.
Important safety Notice ..................................................................... 4 Electrical & Installation requirements ............................................. 5 Electrical requirements .............................................................. 5 Before installing the hood ........................................................... 5 List of Materials ................................................................................. 6 Parts supplied: .................................
Important safety Notice READ AND SAVE THESE INSTRUCTIONS CAUTION: FOR GENERAL VENTILATING USE ONLY. DO NOT USE TO EXHAUST HAZARDOUS OR EXPLOSIVE MATERIALS OR VAPORS. WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: A. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer. B.
ELECTRICAL REQUIREMENTS Important: Observe all governing codes and ordinances. It is the customers responsibility: To contact a qualified electrical installer. To assure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70 latest edition*, or CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No.0-M91 - latest edition** and all local codes and ordinances.
List of Materials PARTS SUPPLIED: Blower unit housing Hood canopy Metal filter x 1 Halogen light bulb x 2 (x 4 on EAT E42ASX) Duct covers Duct Cover support bracket (3 pieces to assemble) Hardware Packet: 4x8 screws x 4 (to assemble Duct cover support bracket) 6x70 screws x 2 (to fix duct cover support bracket) 10x60 wall anchors x 2 (to fix duct cover support bracket) 5x45 screws x 3 (2 to fix lower support bracket + 1 to fix blower unit) 6,5x3,5 screws x 8 (to fix hood canopy to blower uni
Dimensions and clearances www.zephyronline.com 13" 6/16 36" - 42" 1/2" 11" 12/16 ceiling 12" 2"min 10" 1/2 Ducting and conduit area passage(Duct bends are not considered) 12" max 44" 2/16 21"min min 27" 9/16 Side Cabinet max 48" 7/16* min 33" 7/16* Side Cabinet 36" - 42" min. cabinets opening widths 26" 12/16 24" to 32" bottom of canopy to cooking surface 20" 8/16 * Ductless (recirculating) version ONLY Note: if necessary order the proper duct cover extension kit.
Installation Instructions Closely follow the instructions set out in this manual. All responsibility, for any eventual inconveniences, damages or fires caused by not complying with the instructions in this manual, is declined. VENTING METHODS The hood is equipped with a transition B for discharge of fumes to the outside (Ducting version). Should it not be possible to discharge cooking fumes and vapour to the outside, the hood can be used in the Ductless (recirculating) version.
Duct pieces Equivalent number lenght x used = Duct pieces Total Equivalent number lenght x used = Total 3 1/4 x 10 Rect., straight 1 Ft. x ( )= Ft. 6" Round 30 Ft. wall cap with damper x ( )= Ft. 6 Round,, straight 1 Ft. x ( )= Ft. 6 Round, roof cap 30 Ft. x ( )= Ft. 7", 8 Round,, straight 1 Ft. x ( )= Ft. 6 Round to 3 1/4 x 10 rect. transition 1 Ft. x ( )= Ft. 3 1/4 x 10 Rect.90° elbow 15 Ft. x ( )= Ft. 16 Ft. x ( )= Ft. 3 1/4 x 10 Rect.
Installation stud finder. Mark the center of the studs with a vertical line to the right and left of the marked fastener location. ASSEMBLING THE DUCT COVER SUPPORT BRACKET (3 PARTS): The three parts should be fixed with 4 screws, the support extension is adjustable and should correspond to the internal width of the upper duct cover. 8. Note: all fastener location must span the studs otherwise proceed as follows: Cutout drywall along marked lines.
14. Note: disregard this step if intending to install a inline blower. Purchase and install the Internal blower (see paragraph Before installing the hood - Parts not supplied for model reference). 15. If supplied dismounted for shipping, assemble the lower part of the hood with the internal blower housing: a. Remove the grease filter (see also Care & Use section - Charcoal filter). b. Rest the internal blower housing on a flat surface and thread completely the lower part of the hood onto it. c.
Installation 16. Hang hood with the 2 mounting hooks. 20. Electrical connection WARNING Excessive Weight Hazard - Use two or more people to move and install range hood. Failure to do so can result in back or other injury. WARNING Electrical Shock Hazard Warning: Turn off power circuit at the service panel before wiring this unit. 120 VAC, 15 or 20 Amp circuit required. 17.Level the appliance, using a carpenters level across bottom of hood with leveling screws in mounting hooks.
Conduit Duct cover support bracket J-Box cover Duct cover support bracket Upper duct cover Connect black wire from service panel to black or red in junction box, white to white and green to green-yellow. Close junction box cover. 21. Note: disregard this step if the hood has been fitted with an internal blower. Purchase and install a In-line blower (see paragraph Before installing the hood - Parts not supplied for model reference). Lower duct cover 22.
Description of the hood & Controls 1 2 3 4 5 6 7 Control panel Grease filter Grease filter release handle Halogen lamp (position and nr. of lamps may vary) Vapour screen Duct cover Air outlet (used for Ductless version only) 7 6 1 4 2 3 5 4 CONTROLS Use the high suction speed in cases of concentrated kitchen vapours.
Prior to any maintenance operation ensure that the cooker hood is disconnected from the power supply. CLEANING The cooker hood should be cleaned regularly internally and externally. For cleaning use a cloth moistened with a neutral liquid detergents. Avoid abrasive detergents. Warning: Failure to carry out the basic standards of the cleaning of the cooker hood and replacement of the filters may cause fire risks. Therefore we recommend oserving these instructions.
Trouble Shooting Issue After installation, the unit doesnt work? Cause What to do 1. The power source is not turned ON. 1. Make sure the circuit breaker and the units power is ON. 2. The power line and the cable locking connector is not connecting properly. 2. Check the power connection with the unit is connected properly. 3. The switch board and control board wirings are disconnected. 3. Make sure the wirings between the switch board and control board are connected properly. 4.
TO OBTAIN SERVICE UNDER WARRANTY: Staple your receipt here. Proof of the original purchase date is needed to obtain service under the warranty. or any Service Related Questions, please call: 1-888-880-8368 TO OBTAIN SERVICE UNDER WARRANTY: You must present proof of original purchase date. Please keep a copy of your dated proof of purchase (sales slip) in order to obtain service under warranty.
List of Parts and Accessories Part Description halogen bulb, 12V 20 W Part# Z0B-0013 metal filter Part Description Part# Ductless Recirculating Kit ZRC-00AT charcoal replacement filter Z0F-C060 duct cover extension kit Z1C-00AT internal blower - 600 cfm EBI-600A in-line blower - 1100 cfm EBN-1100A 18
www.zephyronline.