Installation Instructions

8
Installation
• It is recommended that the vent system be installed before
hood is installed.
• If you are installing the optional backsplash with shelves
for heat lamps, follow the instructions included with that
product.
• If possible, disconnect and move freestanding or slide-in
range from cabinet opening to provide easier access to
rear wall.
• Before making cutouts, make sure there is proper clearance
within the ceiling or wall for exhaust vent.
• Check that all installation parts have been removed from
the shipping carton.
1 Disconnect power.
2 Determine which venting method to use: roof or wall
exhaust.
NOTE: This hood is factory set to vent through the top air
exit. If you decide to use the rear vent exit, you have to
remove the rear vent cover and relocate it to the top vent
exit.
3 Select a flat surface for assembling the range hood. Place
covering over that surface.
Veting Methods
Outside Top exhaust
Vertical duct Ø 10” (25.4 cm)
Use the diagram or the hood as a template and mark the
locations on the cabinet’s bottom or roof for ductwork, elec-
trical wiring and keyhole screw slots.
WALL
FRONT OF THE HOOD
A
CL
C
D
E
B
F
G
H
Ø 1”
(25.4 mm)
3
⁄4” (19 mm)
5
1
⁄4”
(133mm)
5
1
⁄4”
(133mm)
10
1
⁄2”
(266 mm)
ECL630S3 ECL136S3 ECL142S3 ECL148S3
A 30” (760 mm) 36” (912 mm) 42” (1066 mm) 48” (1217 mm)
B 12” (305 mm)
C 1” (25.4 mm)
D 2
5
⁄8” (65 mm)
E 7
1
⁄2” (190 mm)
F 3
9
⁄16” (90 mm) 5
15
⁄16” (150 mm) 6
7
⁄16” (164 mm)
G 2” (50 mm)
H 3
1
⁄2” (89 mm)
Outside rear exhaust
Horizontal duct Ø 10” (25.4 cm)
Use the diagram or the hood as a template and mark the
locations on the wall for ductwork, electrical wiring and ke-
yhole screw slots.
TOP OF
THE HOOD
CL
EE D
B
4”
(102 mm)
F
G
H
I
J
Ø 1”
(25.4 mm)
5
1
⁄4”
(133mm)
5
1
⁄4”
(133mm)
10
1
⁄2”
(266 mm)
A
D
B
C C
ECL630S3 ECL136S3 ECL142S3 ECL148S3
A 30” (760 mm) 36” (912 mm) 42” (1066 mm) 48” (1217 mm)
B 9
7
⁄8” (250 mm)
C 4” (100 mm)
D 7
9
⁄16” (192.6 mm)
E 3
7
⁄16” (87 mm) 5” (127 mm) 5
13
⁄16” (147 mm) 6
9
⁄16” (167 mm)
F 2
15
⁄16” (75 mm) 5
5
⁄16” (135 mm) 5
7
⁄8” (149 mm)
G 7
1
⁄2” (192 mm)
H 2” (50 mm)
I 6
2
⁄8”(157 mm)
J 3
11
⁄16”(94 mm)
1 Remove the grease filters.
2 Remove the blower mounting screws. Put the screws in a
safe place in order to use them again.
3 Set free the two blower springs from the top of the range
hood housing.