Use, Care, and Installation Guide Guide d’utilisation, d’entretien et d’installation Guía de instalación, uso y mantenimiento READ AND SAVE THESE INSTRUCTIONS LISEZ CES INSTRUCTIONS ET CONSERVEZ-LES MODELS: EGB224SS LEA Y CONSERVE ESTAS INSTRUCCIONES LIB0175565 PRINTED IN MEXICO 1
English Contents Important Safety Notice ���������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������3 Electrical & Installation Requirements ������������������������������������������������������������������������������������������������������������������������������������������������������������������������������4 Before Installing the Hood ��������������������
Important Safety Notice I CAUTION FOR GENERAL VENTILATING USE ONLY. DO NOT USE TO EXHAUST HAZARDOUS OR EXPLOSIVE MATERIALS OR VAPOURS. IWARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: A. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer. B.
Electrical & Installation Requirements Before Installing the Hood IMPORTANT 1 It is the customer’s responsibility: • To contact a qualified electrical installer. 2 3 Observe all governing codes and ordinances. • To assure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70 — latest edition*, or CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No.0-M91-latest edition** and all local codes and ordinances.
List of Materials Removing the packaging. Parts Not Supplied I CAUTION Remove carton carefully, Wear gloves to protect against sharp edges. • Drill with 1⁄8” (3 mm), ½” (13 mm) and 1¼” (30 mm) drill bits IWARNING Remove the protective film covering the product before putting into operation. • Pencil • Wire stripper or utility knife Parts Supplied Supplied Part Pieces 2 3.5 x 9.
Vertical Discharge Use a rectangular duct 31⁄4” x 10” or use a 7” (17.8 cm) round transition for discharge of fumes to the outside. Preparation Do not cut a joist or stud unless absolutely necessary. If a joist or stud must be cut, then a supporting frame must be constructed. Fittings material is provided to secure the hood to most types of walls/ceilings. However, a qualified technician must verify suitability of the materials in accordance with the type of wall/ceiling.
NOTE: Mark the thin area of the slot. On the back wall mark the holes for the security screws (B). Set range hood aside on a covered surface. A 1⁄4" (6.4 mm) 7. A. Keyhole slot Use 8⁄25” (8mm) drill bit and drill 2 pilot holes in the marks for the security screws, then place the drywall anchors. B Prepare Range Hood 1. Set the range hood on its back on a covered surface. 5. Use 1⁄8” (3 mm) drill bit and drill 4 pilot holes. NOTE: Make the drill holes on the thin area of the slot. A A.
NOTE: Mark the thin area of the slot. On the back wall mark the holes for the security screws (B). Set range hood aside on a covered surface. Attach Vent Damper or Transition 3¼” x 10” (8.3 x 25.4 cm) Rectangular Vent Damper A A. Keyhole slot 5 Use 1⁄8” (3 mm) drill bit and drill 4 pilot holes. NOTE: Make the drill holes on the thin area of the slot. 1 A A. Drill pilot hole 6 Install the 4 - .45 cm x 1.3 cm mounting screws in pilot holes. Leave about ¼” (6.
Mark Hole Locations 1 Determine and clearly mark a vertical centerline (A) on the wall and cabinet bottom. Mark and Cut Vent Opening For a non-vented (recirculating) installation: skip “Mark and Cut Vent Opening” step. For 3¼” x 10” (8.3 x 25.4 cm) Rectangular Vent System Roof Venting To make a 4” x 10½” (10.16 cm x 26.7 cm) rectangular cutout on the underside of cabinet top and bottom: 1 Mark lines 1½” (3.95 cm) and 44⁄5” (12.25 cm) from the back wall on the centerline of the underside of cabinet.
For 7” (17.8 cm) Round Vent System (Roof Venting) To make a circular vent opening on the underside of the cabinet top: 1 2 3 4 Mark a centerline on the underside of the top of cabinet. Mark a line 5” (12.8 cm) from the back wall on the underside of the top of cabinet. Use a compass or a circle template to draw a circle with a diameter of 7½” (19 cm). Use saber or keyhole saw to cut the circular vent opening. Repeat steps 1-3 for the underside of the top of the cabinet.
Electrical Connection 1 IWARNING ELECTRICAL SHOCK HAZARD. DISCONNECT POWER BEFORE SERVICING. REPLACE ALL PARTS AND PANELS BEFORE OPERATING. FAILURE TO DO SO CAN RESULT IN DEATH OR ELECTRICAL SHOCK. 2 G C D E A B A. White wires B. Black wires C. UL listed wire connector D. Green (or bare) ground wire E. Homepower supply cable F. UL listed or CSA approved 1⁄2” strain relief G.
Description of the Hood Control 4 1 2 3 4 5 6 1 3 2 1. 2. 3. 4. a) b) c) d) e) f) Light On Light Off Blower Blower Blower Blower On speed minimum button speed medium button speed maximum button Blower and light controls LED lamps Grease filter handle Grease filter Operating the light Move the light switch to turn on and off the light. Operating the blower Move the motor switch to position 1, 2 or 3 depending on the desired speed.
Charcoal Filter If the model is not vented to the outside, the air will be recirculated through disposable charcoal filters that help remove smoke and odors. The charcoal filters cannot be cleaned. They must be replaced. The charcoal filters are clipped inside of each metal grease filter (mounting instructions included with charcoal filters kit). The charcoal filters should be replaced every 4-6 months (depending on hood usage). NOTE: DO NOT rinse, or put charcoal filters in an automatic dishwasher.
Register your product in ELICA North America WARRANTY TWO-YEAR LIMITED WARRANTY elica.com and earn a 3rd year of factory warranty, covering all parts plus in-home labor. TO OBTAIN SERVICE UNDER WARRANTY Owner must present proof of original purchase date. Please keep a copy of your dated proof of purchase (sales slip) in order to obtain service under warranty.
