Use, Care, and Installation Guide Guide dutilisation, dentretien et dinstallation Guía de instalación, uso y mantenimiento Grace Design Team Elica READ AND SAVE THESE INSTRUCTIONS LISEZ CES INSTRUCTIONS ET CONSERVEZ-LES LEA Y GUARDE ESTAS INSTRUCCIONES LIB0005783 ed 10/09 printed in Italy
English French Spanish Contents page 2 Sommaire page 17 Contenido página 32 English Contents Important safety Notice..............................................................................................................................................3 Electrical & Installation requirements ......................................................................................................................4 Electrical requirements ............................................................
READ AND SAVE THESE INSTRUCTIONS Important safety Notice WARNING CAUTION TO REDUCE THE RISK OF INJURY TO PERSONS, IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING: a) SMOTHER FLAMES with a close-fitting lid, cookie sheet, or other metal tray, then turn off the gas burner or the electric element. BE CAREFUL TO PREVENT BURNS. If the flames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT. b) NEVER PICK UP A FLAMING PAN - you may be burned.
Electrical & Installation requirements Electrical requirements Before installing the hood IMPORTANT 1. For the most efficient air flow exhaust, use a straight run or as few elbows as possible. CAUTION: Vent unit to outside of building, only. Observe all governing codes and ordinances. It is the customer’s responsibility: To contact a qualified electrical installer.
List of Materials Parts supplied Parts not supplied • • • • • Blower unit housing Aesthetic covers x 3 Glass x 1 Stainless steel mesh filter Halogen light bulb x 1 • • Hardware Packet: Support bracket with cables and hooking brackets x 1 Cover x 1 Aesthetic cover bracket x 3 Template Use, Care and Installation Guide Torx adapter T10 x 1 Torx adapter T20 x 1 5x45 screws x 3 (To attach support bracket to ceiling) 3,5x6,5 screws x 11 (2 To attach j-box to support bracket, 6 for installing the aesthetic c
Dimensions and Clearances 6
Ducting Options and Examples Closely follow the instructions set out in this manual. All responsibility, for any eventual inconveniences, damages or fires caused by not complying with the instructions in this manual, is declined. Venting methods The hood is supplied in the Ductless (Recirculating) version and is used without an extracted fumes discharger conduit . Fumes and steam are recycled through the F deflector. Preparation Do not cut a joist or stud unless absolutely necessary.
Installation Installation - Ductless (Recirculating) version 1. Pre-installation calculations 2. Preparation of mounting surface C = Counter Height (36" standard) H = Prefered Height of Hood Bottom above counter L = Chimney Structure Height, your installation. Installing supports above ceiling drywall. L = X-Y-H+1" 3/16 a) Select a hood preference height H that is comfortable for the user. b) Calculate Hood height your installation L = X-Y-H+1" 3/16 .
5. Install the aesthetic cover brackets and lock with 6 screws. Consult a professional if you have difficulties or your installation is unique. Consult template and Figs.above. c. Install drywall; then refinish ceiling. Determine the required position for the conduit and cut a 1-1/4" (3.2 cm) hole at this location. Run wires through hole according the National Electrical Code or CSA Standards and local codes and ordinances. d.
8. Fix the hood to the hooking brackets and secure with 1 screw for each bracket (COMPULSORY FIXING). 10. Electrical connection WARNING Electrical Shock Hazard Warning: Turn off power circuit at the service panel before wiring this unit. 120 VAC, 15 or 20 Amp circuit required. ELECTRICAL GROUNDING INSTRUCTIONS THIS APPLIANCE IS FITTED WITH AN ELECTRICAL JUNCTION BOX WITH 3 WIRES, ONE OF WHICH (GREEN/YELLOW) SERVES TO GROUND THE APPLIANCE.
15. Insert the grease filter. For locking, rotate the 3 fixing pins by 90°. 13. Fix the junction box to the support bracket on the ceiling with 2 screws. Important! Replacement of the interconnection cable must be carried out by the authorised after-sales technical service. 14. Fit the control shaft in the correct position by pushing it upwards. Connect the electricity. 16. Apply the aesthetic tabs (press-on) to cover the hood fixing rib points.
17. Insert the cover between the support cables, making sure they enter the special slots on the cover. Important! Leave enough cable so that it passes easily through the slot obtained in the cover. Secure the cover with 3 grub screws already screwed on the support bracket. Note: The 3 fixing screws secure the cover by virtue of the friction they exert on the cover itself, and therefore must not be completely tightened. 18. Check all light bulbs to make sure they are secure in their sockets.
Description of the hood & Controls 1 2 3 4 Control panel Grease filter Halogen lamp Aesthetic cover 13
Center light check The center light may be switched on and off by pressing the T2 button on the control panel. Controls Use the high suction speed in cases of concentrated kitchen vapours. It is recommended that the cooker hood suction is switched on for 5 minutes prior to cooking and to leave in operation during cooking and for another 15 minutes approximately after terminating cooking.
Maintenance ATTENTION! Before performing any maintenance operation, isolate the hood from the electrical supply by switching off at the connector and removing the connector fuse. Or if the appliance has been connected through a plug and socket, then the plug must be removed from the socket. Cleaning The cooker hood should be cleaned regularly (at least with the same frequency with which you carry out maintenance of the fat filters) internally and externally.
Replacing the light bulb Disconnect the hood from the electricity. Warning! Prior to touching the light bulbs ensure they are cooled down. Replace Lights • Remove the damaged light (twist counter clockwise) and replace with a new 120 Volt, 50 Watt (maximum) 50° halogen light made for a GU10 base, suitable for use in open luminarie. Some models envisage lateral lamps: Replace them with identical forms of 40W (E12) max). Remove cover to access the lamp housing.