Installation instructions
11
Theclockcanbedisplayedinatwelvehourformatand
valid clock times are from 1:00 to 12:59.
Theclockcanbereprogrammedpressingthe“Timer”
key for 5 seconds, and after, the clock can be adjusted
withthe“+”and“-”keys.Colon“:”willashindicating
clock programming mode.
Theusercanhaveminuteincrements/decrementsof1
minute,butiftheuserkeeppressingthe“+”/”-”keys
for more than 1 second, the increments / decrements will
be of 5 minutes. During this option the control will
round to the nearest 5 minutes.
Theusercannishonreprogrammingtheclockpressing
the“timer”key.
After1minuteofnokeypressedthecontrolwillaccept
the programmed clock time and will add one minute
to the set clock.
Grease lter saturation alarm
Afterthirtyfanfunctionalhours,thedisplaywillshow
“GreaseFilter”ifthefanisactive.Whenthisiconis
showninthedisplay,thegreaseltersinstalledare
required to be washed.
Toresetthegreaseltersaturationalarmtheusermust
pressthe“+”keyfor5seconds,afterthisactionthe
icon“greaselter”isnotdisplay,andthehoodhasthe
normal display operation.
Charcoal lter saturation alarm (Recirculating accessories)
Afteronehundredandtwentyfunctionalhoursofthefan,
thedisplaywillshow“CharcoalFilter”ifthefanisactive.
Whenthisiconashesondisplay,thecharcoallters
installed are required to be replaced or reactivated.
Toresetthegreaseltersaturationindicationtheuser
mustpressthe“-”keyfor5seconds,afterthistime
theicon“charcoallter”isnotdisplayandthehoodhas
the normal display operation.
Audible signal activation and deactivation
Theaudiblesignalscanbeactivatedordeactivated
pressingthe“Light”keyfor5seconds.
If the audible signal is activated, a tone must sound and
the“Snd”symbolmustappearonthedisplayfor2second.
Iftheaudiblesignalisdeactivated,the“Snd”symbolmust
appear on the display for 2 second and no sound must sound.
Charcoal lter inclusion and exclusion
(Recirculating accessories)
Thecharcoallterinclusionorexclusioncanbesetby
pressingthe“-”and“+”keysatthesametimefor5seconds.
TheInclusionorexclusionofcharcoalltermustbe
selectedwhilethelampsandthemotorareOFF.
Whenthecharcoalhasbeenexcluded,thecharcoallter
alarm is disabled.
Heat sensor
Thecontrolisequippedwithaheatsensorthatwillturn
on the blower at second speed if excessive heat
occurs(over70°C)surroundingthecontrolarea.
IftheblowerisOFForifitisoperatingatrstspeed,the
blower will be set automatically to second speed.
During this state, the user may raise the blower speed to
third speed but can not decrease the speed.
When the temperature level on the hood drops to normal,
theblowerwilloperateinthesettingdenedbytheuser
before the alarm occured.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Metal grease lter maintenance
Themetalltertrapsgreasereleasedbyfoodsonthecook-
top.Theltermustalwaysbeinstalledwhenthehoodis
operating / used.
To remove:
Pushthelterlock/pivotindirectiontothecenterofthe
lter.
Oncethepivotispushedpulldownthelterslowly.
To replace:
Inserttheltertabsintotheslots
Pushthelterlock/pivotindirectiontothecenterofthe
lter.
Oncethepivotispushed,raisethelterslowlyuntilthe
top and release the pivot.
To clean:
Swishthelterinhotsoapywaterandrinseinclean
water or wash it in the dish washer.
Do not use abrasive cleaners.
Hood maintenance
Clean with a damp, soapy cloth and dry with a clean cloth.
Aglasscleanermayalsobeused.
ATTENTION:Donotwetthecontrolpanel.
Do not use a steel wool pad; it will scratch the surface.
Tocleanthestainlesssteelsurface,usewarmsudsy
water,stainlesssteelcleanerorpolish.Alwayswipe
the surface in the direction of the grain. Follow the cleaner
instructions for cleaning the stainless steel surface.
•
•
•
•
•
•
•
•
•
•