Furious Three RG User Manual SKU#: UPC#: FUR128 818651029314
©2021 Eliminator Lighting all rights reserved. Information, specifications, diagrams, images, and instructions herein are subject to change without notice. Eliminator logo and identifying product names and numbers herein are trademarks of Eliminator Lighting. Copyright protection claimed includes all forms and matters of copyrightable materials and information now allowed by statutory or judicial law or hereinafter granted.
CONTENTS General Information 4 Limited Warranty (USA Only) 5 Safety Guidelines 6 Laser Warnings and Safety 8 Maintenance Guidelines 10 DMX Setup 11 Overview 14 Installation Instructions 15 System Menu 17 DMX Traits 19 Dimensional Drawing 23 Specifications 24 3
G E N E R A L I N F O R M AT I O N INTRODUCTION Please read and understand all instructions in this manual carefully and thoroughly before attempting to operate this product. These instructions contain important safety and use information. UNPACKING: This product has been thoroughly tested and has been shipped in perfect condition. Carefully check the shipping carton for damage that may have occurred during shipping.
L I M I T E D W A R R A N T Y ( U S A O N LY ) A. Eliminator Lighting, an ADJ Products, LLC brand, hereby warrants, to the original purchaser, ADJ Products, LLC products to be free of manufacturing defects in material and workmanship for a prescribed period from the date of purchase (see specific warranty period listed below). This warranty shall be valid only if the product is purchased within the United States of America, including possessions and territories.
SAFETY GUIDELINES THERE ARE NO USER SERVICEABLE PARTS INSIDE THESE DEVICES. DO NOT ATTEMPT ANY REPAIRS YOURSELF; DOING SO WILL VOID YOUR MANUFACTURER’S WARRANTY. DAMAGES RESULTING FROM MODIFICATIONS TO THESE DEVICES AND/OR THE DISREGARD OF SAFETY INSTRUCTIONS AND GUIDELINES IN THIS MANUAL VOID THE MANUFACTURER’S WARRANTY AND ARE NOT SUBJECT TO ANY WARRANTY CLAIMS AND/OR REPAIRS.
SAFETY GUIDELINES This unit may “pop” the fuse if the maximum allotted load of 3 amps is reached. • • • • • • • • • • • • • • • To reduce the risk of electrical shock or fire, do not expose this unit rain or moisture. Do not spill water or other liquids into or on to your unit. Do not attempt to remove or break off the ground prong from the electrical cord. This prong is used to reduce the risk of electrical shock and fire in case of an internal short.
LASER WARNINGS AND SAFETY After completing setup, and before public use, test the laser to ensure proper function. Do not use if any defects are detected. Do not use if the laser emits only a few laser beams rather than dozens/ hundreds, as this could indicate damage to the diffraction grating optic, and could allow emission of laser intensity levels that exceed Class 3R. • • • • • • • • • • • • • Do not point lasers at people or animals. Never look into the laser aperture or directly at laser beams.
LASER WARNINGS AND SAFETY 9
MAINTENANCE GUIDELINES DISCONNECT POWER BEFORE PERFORMING ANY CLEANING OR MAINTENANCE! CLEANING Frequent cleaning is recommended to ensure proper function, optimized light output, and an extended life. The frequency of cleaning depends on the environment in which the device operates: damp, smoky, or particularly dirty environments can cause greater accumulation of dirt on the fixture housing and/or light fixture optics.
DMX SETUP DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used as a form of communication between intelligent fixtures and controllers. A DMX controller sends DMX data instructions from the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only have a DATA “OUT” terminal).
DMX SETUP Notice: Be sure to follow figures two and three when making your own cables. Do not use the ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield conductor to come into contact with the XLR cable’s outer casing. Grounding the shield could cause a short circuit and erratic behavior. Special Note: Line Termination. When longer runs of cable are used, you may need to use a terminator on the last unit to avoid erratic behavior.
DMX SETUP DMX ADDRESSING All fixtures should be given a DMX starting address when operating with a DMX controller, in order to ensure that the correct fixture responds to the correct control signal. This digital starting address is the channel number from which the fixture starts to “listen” to the digital control signal sent out from the DMX controller. This starting DMX address is assigned by setting the correct DMX address on the digital control display on the fixture.
OVERVIEW 1. Laser Aperture 2. Mounting Bracket 3. Bracket Adjustment Knobs (x2) 4. Sound Indicator 5. DMX Indicator 6. Display Screen 7. Auto Mode Indicator 8. Secondary Mode Indicator 9. Sound Sensitivity Adjustment 10. DMX Out 14 11. DMX In 12. Enter Button 13. Down Button 14. Up Button 15. Function Button 16. Laser Safety Switch 17. Fuse 18. Power In 19. Power Out 20.
I N S TA L L AT I O N I N S T R U C T I O N S FLAMMABLE MATERIAL WARNING Keep devices at least 5.0 feet (1.5m) away from flammable materials and/or pyrotechnics. ELECTRICAL CONNECTIONS A qualified electrician should be used for all electrical connections and/or installations.
I N S TA L L AT I O N I N S T R U C T I O N S CLAMP INSTALLATION This fixture features a mounting clamp attachment point, which is located on the mounting yoke, as well as a safety cable rigging point, located on the rear face of the unit near the power connection (see the illustration below).
CONTROL PANEL SYSTEM MENU The device includes an easy to navigate system menu that can be accessed via a set of control buttons located on the back face of the device below the digital display. FUNC: Press to cycle through main menu options (Auto, Sound, Secd, DMX). ENTER: Press to confirm selection and open up the option sub-menu, if applicable. UP/DOWN: Press to scroll through menu or sub-menu options.
SYSTEM MENU Aut0: Laser + RGBWY + 8x1WLED Aut1: Laser + RGBWY Auto Aut2: Laser + 8x1WLED Aut3: RGBWY + 8x1WLED Aut4: RGBWY ENTER to confirm, then UP/DOWN to select display speed. S0 (fastest) to S100 (slowest). Aut5: Laser Aut6: 8x1WLED Sou0: Laser + RGBWY + 8x1WLED Sou1: Laser + RGBWY Sound Sou2: Laser + 8x1WLED Sou3: RGBWY + 8x1WLED ENTER to confirm, then adjust sensitivity with Sound Sensitivity Adjustment knob.
DMX TRAITS Eliminator Furious Three RG - DMX Traits Software Version 1.
DMX TRAITS Eliminator Furious Three RG - DMX Traits Software Version 1.
DMX TRAITS Eliminator Furious Three RG - DMX Traits Software Version 1.
DMX TRAITS Eliminator Furious Three RG - DMX Traits Software Version 1.
DIMENSIONAL DRAWING 23
S P E C I F I C AT I O N S • • • • • • • • • • • • • • • • • • 3-FX-IN-1 dance party lighting effect: LED Moonflower, Wash and laser effects Dozens of razor-sharp beams fill a dance floor, ceiling or wall Moonflower: 5 x 3W (RGBWY) 5-in-1 LEDs Wash: 6 x 3W (RGBY) Quad LEDs Laser: Red & Green laser diodes 4 control mode: DMX, Sound Active, Auto, Primary/Secondary 4-button LED display menu 9 DMX channels Electronic dimming: 0-100% 3-pin DMX In/Out IEC AC In/Out connectors to daisy chain power Laser On/Off wi
