User Manual

ManualsBrandseLine Technology ManualsCamcordersEPTZ-27IR

Read this Manual carefully before installation and keep it for future reference.

IR PTZ Dome Camera

Summary of content (28 pages)

PAGE 1
IR PTZ Dome Camera Read this Manual carefully before installation and keep it for future reference.
PAGE 2
Operation Manual of P T Z Dome Camera Notice: Precautions: 1.Non-techinician is forbidden to operate this dome device before reading this manual thoroughly. 2.Cut the power supply off before operating the dome device to avoid damage caused by improper operation. 3.Interior of the Dome device are precision optical and electrical device. Heavy pressure, shock and other incorrect operations should be prevented. Otherwise, may cause damage on product. 4.
PAGE 3
Operation Manual of P T Z Dome Camera Content Chapter 1 Product Overview ...................................................................................... 4 1.1 Performance Instructions............................................................................ 4 1.2 Feature Functions Instruction..................................................................... 4 Chapter 2 Menu setting............................................................................................... 7 2.
PAGE 4
Operation Manual of P T Z Dome Camera Chapter 3 Short-cut Operations and Specification of Dome Device ............... 24 Chapter 4 Trouble Shooting of Dome Device .....................................................
PAGE 5
Operation Manual of P T Z Dome Camera Chapter 1 Product Overview 1.1 Performance Instructions ¾ Address of Dome device is from 0～255. The number (address) of dome device in the control system is setup by the hardware (8-digit on and off switch) of dome device. ¾ Integrated multi-protocol and auto protocol differentiation. Note: The dome device only auto differentiate controller of the first communication. ¾ Pan 360 degree continuous scanning. ¾ Tilt 90 degree action plus 2 degree angle adjustment.
PAGE 6
Operation Manual of P T Z Dome Camera screen.) ¾ Operation crosshair function.(Enable this option, the target can be captured more effectively with crosshair on the screen.) ¾ Three PTZ tours operation with 8 minutes record of each tour.(Can real-time monitor and record the action of manual operation) ¾ Six group of programmable vector scans.(including scan speed, dwell time, preshot and interruption between tours) ¾ Auto flip function with 10 degree move up.
PAGE 7
Operation Manual of P T Z Dome Camera than 5 watts, Subversion of the traditional infrared lighting quick decline fatal shortcoming b.
PAGE 8
Operation Manual of P T Z Dome Camera Chapter 2 Menu setting 2.1 Operation instructions Menu operation instruction To make a selection, move the joystick in the Up or Down direction. The on-screen arrow points to the selected option. Using the joystick to the Left or Right position you can change the value of your selection or enter the submenu for the selected option. Press the button CLOSE on the keyboard controller to exit the menu or return to the previous menu(one layer up) Number setup.
PAGE 9
Operation Manual of P T Z Dome Camera 4. Control Options Set the pan or tilt and camera of the dome manually or auto compatible with the entire control system. User individualized operation setting. 5.Camera Options Set camera function. 6. Function Programming Program and execute PTZ and VectorScan etc. 7. SYSTEM SETUP System setup, Including, restore default setup clear memory, color system, dome reset. 2.
PAGE 10
Operation Manual of P T Z Dome Camera 2.4.1 Camera Name Setup Set the camera name 1.NAME CAMERA NAME SETUP 1 NAME ___________ 2 NAME DISPLAY OFF [1].Move the joystick up/down to move the cursor to select the Name. [2].Move the joystick left/right or press OPEN to enter name editing menu. PLEASE ENTER: [3].Joystick left/right to select programming WELCOME_________ position and press OPEN to confirm, joystick left/right again to select( 0~9 or ABCDEFGHIJKLN A~Z ). Press OPEN to confirm selection.
PAGE 11
Operation Manual of P T Z Dome Camera 2.5.2 Control Option Operation Move the cursor to select Auto Flip/Proportional Speed/Pan Reverse/ Tilt Reverse/VectorScan Still/VectorScan AF/-2 Tilt Limit/Speed Limit. Move the joystick left/right or press OPEN to Display on/off/PTZ/Z/OFF ¾ Auto Flip: If the camera lens auto rotates pan 180° then tilt 10° to auto track forward when the lens goes down tilt 90°. ¾ Auto AE: If the camera is AE when the dome device changes its pan or tilt or zoom.
PAGE 12
Operation Manual of P T Z Dome Camera 3.AF Sensitivity ZOOM AND FOCUS 1 ZOOM SPEED 2 DIGITAL ZOOM 3 AF SENSITIVITY 7 ON Steps: [1].Move the joystick up/down to move the cursor to select AF Sensitivity. HIGH [2].Joystick left/right to setup AF Sensitivity function of the camera 2.6.2 Camera Exposure CAMERA EXPOSURE 1 AE MODE AUTO 2 SLOW SHUTTER OFF 3 SHUTTER SPEED AUTO 4 IRIS LEVEL AUTO 5 AGC LEVEL AUTO 6 BRIGHT LEVEL AUTO 7 SPOT AE OFF 8 WDR OFF 1.AE Mode Steps: [1].
PAGE 13
Operation Manual of P T Z Dome Camera 3. Shutter Speed(Shutter Speed works 4. Iris (IRIS works under Manual/IRIS under Manuel/Shutter MD) MD) Steps: Steps: [1].Joystick up/down to move the cursor to select Shutter MD [1].Joystick Up/Down to move the [2].Joystick left/right to set up Shutter [2].
PAGE 14
Operation Manual of P T Z Dome Camera CAMERA EXPOSURE 1 AE MODE AUTO 2 SLOW SHUTTER OFF 3 SHUTTER SPEED AUTO 4 IRIS LEVEL AUTO 5 AGC LEVEL AUTO 6 BRIGHT LEVEL AUTO 7 SPOT AE OFF 8 WDR OFF 7.Spot AE(OFF/ON) Steps: [1].Joystick Up/Down to move the cursor to select Spot AE. [2].Joystick Left/right to set up the Spot AE CAMERA EXPOSURE 1 AE MODE AUTO 2 SLOW SHUTTER OFF 3 SHUTTER SPEED AUTO 4 IRIS LEVEL AUTO 5 AGC LEVEL AUTO 6 BRIGHT LEVEL AUTO 7 SPOT AE OFF 8 WDR OFF 8.
PAGE 15
Operation Manual of P T Z Dome Camera 2.7 Function Programming FUNCTION PROGRAMMING Preset option 1 PRESET 1. Move the joystick left/right or press 2 VECTORSCAN OPEN to enter Function Programming 3 PATTERN options. 2. Move the joystick up/down to move the 4 SECTOR SETUP cursor to select the preset options. 5 MASK ZONE 3. Move the joystick Left/Right or press 6 MASK COLOR OPEN to enter preset options. 7 MOTION 2.7.1 Preset 1.Number [1].
PAGE 16
Operation Manual of P T Z Dome Camera level. without save your selection. PRESET 1 NUMBER 1 2 SET PRESET IRIS OPEN WHEN DONE 3 CALL PRESET 4 DELETE PRESET 5 NAME _____________ 6 NAME DISPLAY OFF STORED 3.Call Preset PRESET 1 NUMBER 1 2 SET PRESET Call Preset [1].Move the joystick left/right or press OPEN. The lens auto switch to current preset position corresponding to the edited No. 3 CALL PRESET 4 DELETE PRESET 5 NAME ____________ 6 NAME DISPLAY OFF 4.
PAGE 17
Operation Manual of P T Z Dome Camera 5. Name PRESET Name 1 NUMBER 1 2 SET PRESET cursor to select the Name. 3 CALL PRESET [2].Move the joystick left/right or press 4 DELETE PRESET 5 NAME OPEN to enter name editing menu. ____________ 6 NAME DISPLAY [1].Move the joystick up/down to move the OFF (Please refer to name setting section of Camera Name Setup) 6. NameDisplay PRESET NameDisplay 1 NUMBER 1 Setup On/Off display on the direction 2 SET PRESET name preset. 3 CALL PRESET [1].
PAGE 18
Operation Manual of P T Z Dome Camera VECTORSCAN 1 NUMBER I:Name Pr:stands for Preset Position. 1 2 PROGRAM A VECTORSCAN Vs:stands for VectorScan. 3 RUN A VECTORSCAN Pt: stands for PTZ Tour. 4 DELETE A VECTORSCAN II:Number Programming-selection based on the name. PROGRAM VECTORSCAN 1 NAME NUM SP DWELL III:SP-Set up the speed of Preset. IV:Dwell 1. Vectorscan running operation steps: 2. I:Select pending Vectorscan track in Number menu 3. II:Joystick Up/Down to select Vectorscan 4.
PAGE 19
Operation Manual of P T Z Dome Camera [3].Joystick Up/Down to select pending PATTERN 1 NUMBER operating 1 programming Pattern(number range:1～3). 2 PROGRAM A PATTERN [4].Joystick Up/Down to move the cursor 3 RUN A PATTERN to select Program a Pattern. 4 DELETE A PATTERN 5 NAME or ______ 6 NAME DISPLAY [5].Press OPEN to enter recording of the manual running trace.as left Fig 1. OFF [6].Press CLOSE to finalize the selection. as left Fig 2. IRIS OPEN TO BEGIN [7].
PAGE 20
Operation Manual of P T Z Dome Camera 2.7.4 Sector Setup Function: To display the sector name when dome in the setted area FUNCTION PROGRAMMING 1 PRESET Sector Setup: [1].Move the joystick up/down to move 2 VECTORSCAN the cursor to select sector setup. 3 PATTERN [2].Move the joystick left/right or press 4 SECTOR SETUP OPEN to enter the setting. 5 MASK ZONE 6 MASK COLOR 7 MOTION SECTOR SETUP 1 NUMBER 1 2 PAN START POS 0.0 3 PAN END POS 0.0 4 TILT START POS 0.0 5 TILT END POS 0.
PAGE 21
Operation Manual of P T Z Dome Camera 2.7.5 Mask Zone Function: User can protect the partial area by mask setting from the whole monitoring area according to the situation. MASK ZONE 1 NUMBER MASK ZONE 1 2 MASK EDIT 3 MASK DISPLAY [1].Number ⑴.Joystick Up/Down to move the cursor to OFF select NUMBER. ⑵.Joystick Left/Right to select pending editing mask areas(from area1-24). [2].Mask Edit ⑴.Joystick Up/Down to move the cursor to select Mask Zone. ⑵.Joystick Left/Right or press OPEN to enter editing. ⑶.
PAGE 22
Operation Manual of P T Z Dome Camera 2.7.7 Motion MOTION MOTION [1].Move the joystick left/right or press 1 PARK ACTION OPEN to enter sub-menu. 2 POWER ON ACTION [2].The menu of “AUTO TRACK SETUP” 3 LIMIT OPERATION is invalid.
PAGE 23
Operation Manual of P T Z Dome Camera ⑴. Select the Action and move the joystick left/right or press OPEN to enter Action. Actionincludes:None/Preset/VectorScan/Pattern/PanScan/AutoScan ⑵.Select the Number and move the joystick left/right or press OPEN to enter. Setup method: refer to preset setup instruction. [3]. Move the joystick left/right or press OPEN to enter the Limit Operation. ⑴.Start Position Move the joystick LIMIT OPERATION 1 START POSITION 0.0 2 END POSITION 0.
PAGE 24
Operation Manual of P T Z Dome Camera 2.8.1 Clear Memory [1].Joystick Up/Down to move the cursor to select Clear Memory. [2].Joystick Left/Right or press OPEN to enter. [3].Press OPEN to Clear Memory or press CLOSE to cancel. ARE YOU SURE TO DO THIS IRIS OPEN TO CONFIRM IRIS CLOSE TO CANCEL Press OPEN PLEASE WAIT... 2.8.2 Restore Def Setting [1].Joystick Up/Down to move the cursor to select Restore Def Setting. [2].Joystick Left/Right or press OPEN to enter. [3].
PAGE 25
Operation Manual of P T Z Dome Camera Chapter 3 Short-cut Operations and Specification of Dome Device 1．Short-cut operation table Number of preset Control Object position position Record line 51 52 Call preset scanning speed Pan-Tilt Control Save preset position Run cruise track Start line Set line scanning starting scanning point Set line scanning ending 53 point Background light On Off Day/Night* Auto Color Camera related Camera menu Camera function OSD OSD* On\Off On\Off 58
PAGE 26
Operation Manual of P T Z Dome Camera 87 Run vectorscan 5 88 Run vectorscan 6 89 Picture freeze* On Dynamic preset Call dynamic point preset point 94 Dome reset Reset dome 95 Main menu Call main menu 96 Set the auto flip On 91 101 Pan continuous Off Off On scanning Notes: 1.These functions differs depending on different types of camera.
PAGE 27
Operation Manual of P T Z Dome Camera 3. Description of “Line-Scanning” function: ¾ Dome device will auto line-scan between two specified points. ¾ User can set the start point by “52+SHOT+ON” and end point by “53+SHOT+ON”. ¾ Line scanning speed set: user keep a manual line scan speed three seconds above, then through“51+SHOT+ACK” to save the speed as line scan speed, use“52+SHOT+ACK” to enable the line scan.
PAGE 28
Operation Manual of P T Z Dome Camera Chapter 4 Trouble Shooting of Dome Device 1.Problem description: After power on without any response, not lock motor nor images. Possible reason: The power circuit maybe have some problem Solution: Check the power cable is connected to power of AC24V. 2.