Ｎｅｔ ＤＶＲ Preface Thank you for selecting our products. We will offer the best service for you wholeheartedly. We take 16 channel DVR (960H) as a sample. In this series, different product models’configuration will have a little difference, and it will work the difference between product function and operation. It is for reference only. We will not provide any new information separately for later firmware update.
Ｕｓｅｒ Ｍａｎｕａｌ CONTENT Preface ....................................................................................................................................................................................................................................................................... 1 Chapter1 Brief Introduction about the DVR ................................................................................................................................................................................
Ｎｅｔ ＤＶＲ 3.3.6 Keyboard Controlling ........................................................................................................................................................................................................................ 18 3.3.7 Intercommunication Port .................................................................................................................................................................................................................... 18 3.
Ｕｓｅｒ Ｍａｎｕａｌ 4.4.1 Quick Backup ..................................................................................................................................................................................................................................... 40 4.4.2 Manual Backup ..................................................................................................................................................................................................................................
Ｎｅｔ ＤＶＲ 4.8.1 Basic Information ................................................................................................................................................................................................................................ 62 4.8.2 HDD Group .......................................................................................................................................................................................................................................
Ｕｓｅｒ Ｍａｎｕａｌ Chapter 1 Brief Introduction about the DVR 1.1 Summarization The series DVR are designed for video/audio digital surveillance system. They are adopting H.264 compress format, integrate the embedded RTOS and processor to realize all of the functions like video and audio acquisition and compression, storing, remote control, Multi-PTZ control and alarm in a single board.
Ｎｅｔ ＤＶＲ Video output: 1 channel composite video output, PAL (625 line), NTSC (525 line), BNC (1Vp-p, 75Ω） 1 channel analog video output (VGA) 2. Audio parameters Audio input: RCA interface port, input resistance: 10KΩ, input extent: Vp-p=2.0V LINE Audio output: RCA interface, input resistance: 10KΩ, input extent: Vp-p=2.0V LINE Voice chat: Input (3.5MM interface, input resistance: 10KΩ, input extent: Vp-p=2.0V LINE in/50mV MIC in) 3. Video compression: Compression arithmetic H.
Ｕｓｅｒ Ｍａｎｕａｌ 2.2 Main Functions High effective RTOS and embedded processor are adopted in this series DVR, as well as all functions needed for the monitoring system are integrated. Code is solidified in the flash chip to keep the system in high stability and reliability. System can also work in a long time surveillance environment and even in stringent circumstance.
Ｎｅｔ ＤＶＲ 9. Support channel title and recording time superpose. 10. Support multiplex operation, can real time recording without impacting other functions. (such as playback, fast forward, slow playback, rewind, network monitor, VOD and remote) 11. Support pre-record feature, and pre-record time is 5-30 seconds. 12. Support record status inquiry function. u Playback functions 1. Support inquiry recording files/pictures by time, fix position by time to record/pictures playback. 2.
Ｕｓｅｒ Ｍａｎｕａｌ u Storing and backup functions 1. Support maximum 2 SATA HDD. 2. Support data lock/unlock/delete for all recording files/pictures. 3. The maximum saving time of recording files/pictures can be set, the DVR will auto delete the data which exceed the setting time. 4. Support set read-only/read-write to HDD. 5. Support HDD quota management, different channels can be arranged different quota for save data. 6. Support USB backup (USB disk or external USB burner). 7. Support backup by internal burner.
Ｎｅｔ ＤＶＲ 5. Support control PTZ/lens/wiper by network. 6. Firmware upgrade through network makes after sale service much easier. 7. Support FTP upgrade. 8. Support NTP timing. 9. Support DDNS. 10. Support alarm upload by email (video lost, motion detection, alarm detection). 11. Support mobile phone survillance. 12. Support email test and DDNS test. u Security guarantee 1. High quality 32 bits embedded microprocessor and embedded RTOS, which ensure the system’s high-affectivity, reliability and stability. 2.
Ｕｓｅｒ Ｍａｎｕａｌ Chapter 3 Equipment Installation and Illustration 3.1 Installation Environment and Cautions Installation environment: ● Normal working temperature is -10℃-55℃. Storage temperature is -10℃-70℃． ● Normal working humidity is 15%-85%. ● The equipment must keep horizontal either in installation or on using. ● Avoid installing in high temperature or humidity conditions. ● Heat release fans are placed for cool down, so you should put the device on ventilated place.
Ｎｅｔ ＤＶＲ ● Video/audio/RS485 devices can’t be plug or draw when the power is on, or else the equipment will be easily damaged. ● Use the power on/off button on the front panel instead of direct shut off the power directly when turn off the Net DVR, so that the hard disk won’t be damaged. ● After installation, machine can automatically detect hard disk. If an unformatted hard disk is detected, system will give off information whether to format the disk (the dvr support format HDD, don’t need operate in PC).
Ｕｓｅｒ Ｍａｎｕａｌ 3.3 Device Interface 3.3.1 Video/Audio Connection Video output: 1 VGA output, 1 HDMI output, 1 composite video signal output. Audio output cautions: connect sound box or MIC output. 3.3.2 USB Backup Interface The U disk for backup should be FAT32 format. If you want to format the U disk, please enter the “HDD Management”to check it. (Specific operation please refer to “HDD Management”) The U disk backup operation please refer to “Backup Operation”. 3.3.
Ｎｅｔ ＤＶＲ + DVR +12V GND Input1 Input2 - NO/NC C Sensor If the distance between the probe and DVR is too far, the probe requires a separate power supply: Please connect 2 side to ground if conditional when use separate power, otherwise long distance transmission maybe make false alarm. 12V power supply DVR +12V GND + Input1 Input2 - NO/NC C Sensor 15 eLineTechnology.
Ｕｓｅｒ Ｍａｎｕａｌ If we parallel connected the sensor, the DVR can not recognize the triggered sensor. User need to have a resistance. +12V GND + - C DVR Input1 Input2 NO/NC Sensor1 + - C NO/NC Sensor2 + - C NO/NC Sensor3 2. Alarm output connection: The alarm output side is normal-off and do not have voltage output. The other alarm equipments (loudspeaker, light, alertor) need the individual power supply. 16 eLineTechnology.
Ｎｅｔ ＤＶＲ supply the power separately Output1A Alarm Outnput1B DVR Normally, Alarm’s power usually is much bigger, preferably supply power separately, and do not use the DVR’s power to supply. Each series alarm output critical parameters are as follows: 240V/AC7A, 125V/AC10A, 28V/DC10A. Exceeding these parameters will damage the motherboard. 17 eLineTechnology.
Ｕｓｅｒ Ｍａｎｕａｌ 3.3.5 RS-485 Connection Attentions for PTZ decoder connection: 1. Confirm that the PTZ decoder and Net DVR are one point ground connected, or common mode voltage might exist to cause the PTZ invalid. 2. Prevent high voltage inroad, carefully dispose connection cables secure thunder proof. RS485: For PTZ control, serial keyboard and transparency port connection. (through network to control PTZ etc.) 3.3.
Ｎｅｔ ＤＶＲ 3.4 Front Panel Description S.N Name 1 (Power) On/Off 2 Number/Letter Mark Note Turn on/off DVR. 1. For video channel shift, 1-8 number corresponds to CH1-CH8. 2. The number keys are used for switch channels when playback mode. (Number/Letter) 0-9/A-Z 3. When setting parameters, select number and English letter input. */Preset #/Call 3 (Function keys) PTZ Login/Lock (Auto) It means preset when in the PTZ control status. It means call when in the PTZ control status.
Ｕｓｅｒ Ｍａｎｕａｌ Format 1. Shift between single and multi channel video when in real time display. (Zoom-) 2. It means “zoom-”when in PTZ control status. 1. Set parameters of each channel, without menu state is valid. Image (Iris) 2. It means “iris+”when in PTZ control status. 1. Edit cancel. 2. Alarm clear. Clear (Iris-) 3. It means “iris -”when in PTZ control status. 3 (Function keys) Page up 1. The drop-down menu option switch. (Focus+) 2. It means “focus+”when in PTZ control status.
Ｎｅｔ ＤＶＲ While supply power to DVR and the system running, this lamp will be lighted. POWER When power supplier cut off, this lamp will be off. HDD 5 (Indication IR lamp area) ALARM IR remote controller indication lamp, it’s light when you use the IR remote controller. Alarm indication lamp: it’s light when there is alarm or it’s off. LOCK Lock indication lamp: it’s light while the remote controller is lock. NETWORK Network indication lamp: it’s light while the network is connected.
Ｕｓｅｒ Ｍａｎｕａｌ 3.5 IR Remote Controller Operation 22 eLineTechnology.
Ｎｅｔ ＤＶＲ Keystroke instruction 1. Power 14. 9WXYZ 27. Menu 2. Mute 15. CALL 28. VGA/TV 3. +, Focus+ 16. Log in/Log off 29. F1 4. -, Focus- 17. Information 30. PTZ 5. Playback 18. Backup 31. Server Index 6. Right/Fast Forward 19. Image/Iris+ 32. 2ABC 7. OK, Play/Pause 20. Shift/Zoom+ 33. 1 8. Return 21. Clear/Iris- 34. 5JKL 9. F2 22. Format/Zoom- 35. 4GHI 10. Auto 23. Record 36. 8TUV 11. Wiper 24. Up, Slow Motion 37. 7PQRS 12. 3DEF 25. Left, Backward 38. 0 13. 6MNO 26.
Ｕｓｅｒ Ｍａｎｕａｌ 3.6 Mouse Operation Besides front panel and remote controller, mouse also can be used to control the DVR’System. Right click the mouse: 1. If the system is in login status, right click the mouse, then shortcut menu will display as right picture: 2. If DVR is locked and in real time monitor status, the login menu will pop out when right click the mouse. The system default setting user name is “admin”, and password is 888888 (Left click mouse to open soft keyboard.
Ｎｅｔ ＤＶＲ Double left click the mouse: 1. Double left click in preview can switch single channel and multi channel. 2. Double click the mouse can clear the mask area and motion area. 3. After callout the PTZ control interface, double click the mouse to move the PTZ control interface to pointing place. Soft keyboard interface as below: 25 eLineTechnology.
Ｕｓｅｒ Ｍａｎｕａｌ 3.7 Menu Operation Description 3.7.
Ｎｅｔ ＤＶＲ 3.7.2 Menu Option Schedule Instruction Menu Data Inquiry Time Inquiry Query the record/pictures by time, and with video data graphical display to precise playback. Event Inquiry Query and playback by event type of record/pictures. Data Management Backup Management Lock/unlock/delete the files. Backup/inquiry/playback for record/pictures (quick, schedule, manual). 1. Record mode: all, manual, schedule, motion detection and alarm record; 2. Bitrate type: VBR, CBR; 3. Definition: FD1, CIF; 4.
Ｕｓｅｒ Ｍａｎｕａｌ Screenshots 4. Screenshot period: 1-5S, screenshot Number: 1 pcs (schedule, motion, alarm); Parameter 5. Enable the screenshot (schedule, motion, alarm). 1. Overwrite: auto, manual; Advanced 2. Maximum days of record saving: 1 week, 1 month, 1 year, Unlimited; Record Setup 3. Maximum days of pictures saving: 1 week, 1 month, 1 year, Unlimited. Manual Record Manual Screenshot Schedule Record Enable manual record. Enable manual screenshot. Enable schedule record.
Ｎｅｔ ＤＶＲ 1. Host name, Open remote control lock, Host id; 2. Video standard: PAL/NTSC; 3. Resolution: 1024*768, 1280*1024, 1440*900, 1920*1080; 4. Language: English; 5. Display device: VGA/CVBS; General Setting 6. Auto lock: 1-10 minutes can be chose or close; 7. Audio device: microphone, sound pick-up; 8. Choose device when booting up; 9. Display power on wizzard. 1. Time setting: edit the time by manual, Time mode switching (12hour mode/24hour mode) and DST setting; Time Setting 2.
Ｕｓｅｒ Ｍａｎｕａｌ PTZ Setting PTZ protocol, address code, channel copy function. Network Setting DHCP, IP address, reserve IP setting, port setting, multicast setting. 1. Record type: all, manual, schedule, motion, alarm; 2. Code stream type: VBR, CBR; 3. Definition: CIF, QCIF; 4. Image quality: 6 level (highest, higher, high, middle, low, lowest); Sub-Stream 5. Frame rate: 2-25 fps adjustable; Network System Setup 6. Code rate: 100K, 256K, 512K, 768K, 1M (CIF); 45K, 60K, 90K, 128K, 256K (QCIF); Setting 7.
Ｎｅｔ ＤＶＲ HDD HDD Group Management SMART System Information Record Status Set the HDD and record channel belong to different group, display the HDD total capacity, free capacity, record time. Query the HDD model, serial number, firmware version, temperature, health status and SMART attribution. Query and display the device model, software version, SCM version, IP address, MAC address, language, resolution.
Ｕｓｅｒ Ｍａｎｕａｌ Logout Shutdown Shutdown Reboot Logout. Shutdown (please press the power switch on front panel when use this option to shutdown). Reboot at local.
Ｎｅｔ ＤＶＲ Chapter 4 Device Operation 4.1 Power On/off and Login /Lock Power on: After connected up the power cable, the front panel of the DVR will start and enter the standby state. Click the “Power”button on the remote controller for 3 seconds to enter the running state. Power off: When the system is under the running state, click “Power”button on the remote controller to popup the shut down interface. And clicked the “Confirm”button, the system will enter the standby state.
Ｕｓｅｒ Ｍａｎｕａｌ 3. To input name and password, you can left click mouse. It will pop out software keyboard. Right click mouse to exit. Note: For the sake of safety, please change the default password immediately. 4.1.
Ｎｅｔ ＤＶＲ 2. System login/lock icon: Single click “ 3. Alarm status icon: Single click “ 4. Audio icon: Single click “ ”to access host after booting, single click “ ”to lock the host. ”to access “alarm status”to query alarm information and clear alarm voice. ”to enable or unable voice. 5. Channel preview order adjust icon: Single click “ ”to adjust the order of preview channels. 6.
Ｕｓｅｒ Ｍａｎｕａｌ 4.3 Data Inquiry and Playback Enter the playback interface by press “Play”on the remote controller and right directional button to choose the “Data inquiry”or choose the “Playback”from main menu (as below picture), confirm and access the inquiry interface. 4.3.
Ｎｅｔ ＤＶＲ l Choose the record type in combobox. l Use mouse to choose the data then click “Play”to playback or double click the data by mouse to playback. l Click last page or next page for page turning. Playback Interface Functions: l Playback: the channel quantity for payback decided by DVR specification. l In playback process, right click the mouse to display or hide the playback control box.
Ｕｓｅｒ Ｍａｎｕａｌ 3. Auto pop-up clip and backup window, as the left picture: 4. Set the parameter (save device, file saved type, backup player), then click backup icon, wait for backup finish. Note: AVI data don’t support inquiry and playback in DVR, use the media player to play in PC. DAT data support inquiry and playback in “Backup Management”, but please use the Hanbang special player to play in PC. l In playback process, click the list icon in player to play the other time data or other channel data.
Ｎｅｔ ＤＶＲ 4.3.3 Data Management You can lock, unlock or delete the files in “Data Management”, the interface as the right picture: l Choose the data type: record or picture. l Choose the channel for inquiry. l Use mouse to select data for lock, unlock and delete. Note: Only when data in unlock status can do lock or delete operation. the recording file which is in recording process can’t be deleted, when data is in lock status only can be unlocked, can’t be deleted. 4.
Ｕｓｅｒ Ｍａｎｕａｌ 4.4.1 Quick Backup 1. In backup management interface, click “Quick backup”after choose the backup channel, file status, select record/picture and type. 2. Then a message of “Are you sure to backup”will pop out. Select “Yes”for backup, till all of the file backup is complete. Note: Quick backup is backup all data what queried. 4.4.2 Manual Backup l Operations method as below: 1. Choose the backup channel, file status, select record/picture, type, then click “Inquiry”. 2.
Ｎｅｔ ＤＶＲ 4.5 Record Setup Record setting menu as right picture: 4.5.1 Record Parameter Before using the record function, it is important to set the record parameters. It is related to video playback and hard disk capacity, etc. After login, select “Record Setup”-> “Record Parameter”to enter the interface as the right picture: l Channel No.: Customer can select the channel by pressing “+”, “-”on remote controller or by the mouse.
Ｕｓｅｒ Ｍａｎｕａｌ 4.5.2 Screenshots Parameter Before using DVR snapshot function, please set the snapshots parameters. It will be related to picture playback effect, snapshot interval and the picture size. Enter “Main Menu”-> “Record Setup”-> “Screenshot Para.”interface as the right picture: l Channel No.: Select the channel which you want to set. l Snapshot type: The snapshot parameters will be active in the selected snapshot type. l Resolution: Support FD1/CIF (960H/Q960H).
Ｎｅｔ ＤＶＲ 4.5.4 Manual Record Manul Record interface is as follows: l When enable manual record, the color of channel button is blue. Disable is gray color. l If you open manual record, it will manual record all the time until you manual close it. If the power supply was cut off, after it have power supply again, it will continue to manual record. There has two way to open Manual Record. Method 1: Press “Record”button in remote controller to enter setting interface, then choose the manual record channel.
Ｕｓｅｒ Ｍａｎｕａｌ 4.5.6 Schedule Record Follow below steps to enter Schedule Record interface: 1. Select the corresponding channel No.. 2. Deployment time: choose the record date for setting, can be everyday or a certain day (multiple choices). Time range setting: choose the time range of record, can be set multiple range in one day, the setting of time according to the time order.
Ｎｅｔ ＤＶＲ Step3: Define the motion detection sensitivity level: There have 5 levels: 1(lowest level )~5(Highest level). When the system detect that have motion in the scene, it will alarm and motion record. If you choose low sensitivity, such as 1, it will alarm only when there has big change in the channel scene. If choose 5, if there have little change in the channel scene, it will motion alarm. Step4: Detection area setting: Yellow color will detect motion. Grey color will not detect.
Ｕｓｅｒ Ｍａｎｕａｌ 4.6.2 Sensor Sensor alarm recording setting steps: Step1: Enter “Main Menu”-> “Record Setup”-> “Record Para.”interface to set the channel pre-record time and delay-record time. Step2: Enter “Main Menu”-> “Alarm Setup”-> “Sensor”, then the interface is the right figure above: Step3: Select Sensor type: Normal on or Normal off. Step4: Select sensor number. Step5: Set sensor deploying time (the specific setting please refer to schedule record).
Ｎｅｔ ＤＶＲ l Full screen: When preview image have multi-channels, if system detect alarm, the alarm channel will full screen display. l Alarm output deployment time: System default set alarm output deployment time is everday 00:00-23:59. 4.6.4 Other Alarms Enter “Main Menu”-> “Alarm Setup”-> “Other Alarms”interface as below: l Alarm type: HDD error, Video lost, Network disconnection, High temperature, Video mask. HDD error, Video lost and High temperature default enable alarm function.
Ｕｓｅｒ Ｍａｎｕａｌ 4.7 System Setup System Setup have sub-menu: General Setting, Time Setting, Output Setting, COM Setting, PTZ Setting and Network Setting, the interface is as follows: 4.7.1 General Setting Enter “Main Menu”-> “System Setup”-> “General”, the interface is the right figure above: l Host Name: Can set your DVR host name. l Open Remote Control Lock: Select and open the remote controller lock function, then you can lock the DVR by remote controller.
Ｎｅｔ ＤＶＲ 4.7.2 Time Setting Enter “Main Menu”-> “System Setup”-> “Time”interface as below: l Time Setting: This function is used to set or modify current system time, the system adopted the perpetual calendar. You can directly input the date number or double click to pop-out calender table change the date, the day will change as the date’s change. Note: Please check the system time when firstly use. Because system time is in close relation with video record, try not to adjust system time on general occasion.
Ｕｓｅｒ Ｍａｎｕａｌ l NTP Setting: NTP: NTP (Network Time Protocol) means to get current time from remote server via network to as DVR system time. Please make sure your DVR can access internet before use NTP. The default sever is hk.pool.ntp.org, port: 123, time zone is GMT+08:00. Time Server: The default time serve can automatically sync time succeed if your network is OK. If the default time server cannot work, you can set the time server which can be connected. Port: Time server port.
Ｎｅｔ ＤＶＲ 1. Channel Setting Enter into “Output”-> “Channel Setting”, the interface is the right figure above. You can set channel name, video mask area, special area, vide adjustment parameter and channel name position. (1) Channel name l Channel name can input max 31 characters. l Left click mouse in the text field, then it will pop out soft-keyboard. The keyboard default as inputting english letters. Can click “Caps”button in soft-keyboard to change case.
Ｕｓｅｒ Ｍａｎｕａｌ (4) Video adjustment l Click “Video adjustment”button in channel setting interface to enter into channel parameter setting interface. Or you can press “Image”button in remote controller or front panel to enter “Video Adjustment”interface after login DVR as right picture: l System default channel parameters: Brightness 128, Contrast 128, Saturation 128, Hue 128. l Channel No.: Used to switch channels, user can also setup all channels directly.
Ｎｅｔ ＤＶＲ 4.7.4 COM Setting Enter into “Main Menu”-> “System Setup”-> “COM”, the interface is as follows. You can make your DVR communicate with COM device via this setting. DVR serial port only have RS485 port. The RS485 is half-duplex for transceiver function. It can connect control keyboard and PTZ simultaneous. l The parameters of RS455 are: Baud rate, Data bit, Stop bit etc.. l COM type: Define COM device type, have PTZ, COM keyboard and Tranparent channel 3 types.
Ｕｓｅｒ Ｍａｎｕａｌ 4.7.5 PTZ Setting Enter into PTZ Setting interface by “Main Menu”-> “System Setup”-> “PTZ Setting”, the interface is as follows: PTZ Control Setting steps: l Set the COM type, COM device and baud rate in COM Setting interface. l Set the PTZ Protocol and address code. (Default PTZ address code correspond to channel number. It means the address code of first channel is 1.) Note: The PTZ protocol, baud-rate and address code should be the same with Dome Camera Protocol.
Ｎｅｔ ＤＶＲ l Setting and calling preset point by mouse: Enter the PTZ status, double left click mouse at the preset input text field to enable the software-keyboard and input the preset No. (such as 001). Right click mouse to quit software-keyboard, then click “Preset”to activate the setting. Then turn the PTZ to another direction, if you click the “Call”and input the No. (001) which you preset to the box, the PTZ will turn to the 001 preset point automatically.
Ｕｓｅｒ Ｍａｎｕａｌ 4.7.6 Network Setting Enter into “Main Menu”-> “System Setup”-> “Network”, the interface is as follows: 1. Network Setting Enter into “Network”-> “Network”, the interface is the right figure above: l DHCP: If there have DHCP server, you can select the “DHCP”option, DVR will obtain a dynamic IP address from the server and displayed within the IP address column. l IP: This IP must be unique. It can’t conflict with the IP of other servers or working stations in the same LAN. Default: 192.168.0.6.
Ｎｅｔ ＤＶＲ Multiple port: The default port is start with 8000. Note: If there are 2 DVRs or above in one section of the net, please ensure that the multiple port is unique, or you cannot open the multiple video. 2. Sub-Stream Enter into “Network”-> “Sub-stream”interface as below picture. Sub-stream is related to Network transmission and network record storage. When you preview DVR host playback the record by remote network, it will use the Sub-stream (Network-Stream) to transmit the data. Please refer to 4.5.
Ｕｓｅｒ Ｍａｎｕａｌ 4. PPPOE Select “Network”-> “PPPOE”, and the interface is as follows: PPPOE is one of the mode to connect to the WAN: Connect to the WAN by system via dialing the ADSL directly. Please get the PPPOE account from network operator. l Username: ADSL account user name. l Password: ADSL account password. l Auto Connect: If you select this option, system will automatically connect the WAN after disconnection.
Ｎｅｔ ＤＶＲ 5. Email Setting After login, enter into email setting interface follow “Network”-> “Email setting”, the functions support email upload are “motion detection”, “sensor detection”, “HDD error”, “video lost”, “over temperature”, “video shield”, the interface is the right figure: Email linkage setting steps: (1) First enable the “Email Linkage”setting in Motion or Sensor or Video lost interface. (2) Set the email server address. Default is smtp.126.com.
Ｕｓｅｒ Ｍａｎｕａｌ 7. Compound Channel After entered into “Compound Channel”interface, you will have below interface: Compound channel function is that it can display multiple any channels in the Compound channel in web browser netview interface. a. Set compound channel, select “Enable”button, click “Parameter Setting”button to enter into the interface as below picture: b. Compound channel parameter setting please refer to “4.5.1 Record Parameter Setting”.
Ｎｅｔ ＤＶＲ 4.7.7 Input Settings Please do confirm and set the video image resolution is FD1 or 960H before you connect video input. It’s is very important. It will be related to record parameter setting, snapshot parameter setting, Sub-stream parameter setting, record file resolution, snapshot picture resolution and sub stream resolution. Please set the input setting in “Main Menu”-> “System Setup”-> “Input Settings”interface as below: 4.
Ｕｓｅｒ Ｍａｎｕａｌ 4.8.1 Basic Information You can check the general information of HDD in HDD management, the interface is as follows: 1) Check the HDD general information: The first row display the disk number corresponding to disk interface; The second row display the HDD device; The 3, 4, 5, 6 rows display the partition type, status, total capacity, and available capacity.
Ｎｅｔ ＤＶＲ 4.8.2 HDD Group Note: You can choose the right channel record to specified HDD group. It can take you follow convenience: 1) Can make sure specified channel record to specified HDD. 2) According to channel data quantity size specifi the right HDD. Reasonably set each channel storage space. You can select “HDD Group”sub-menu in “HDD Management”, the interface is the right figure above. System support maximum 4 HDD group.
Ｕｓｅｒ Ｍａｎｕａｌ 4.9.1 System Information System information will display the interface as follows: 4.9.2 Record Status Can quickly query system current record state. The system can display the “Record mode”, “Image quality”, “Definition”, “Audio(Enable/None)”, “Bitrate”of each channel in the state list. If the system is recording, it will display one record mode of Manual/Schedule/Motion/Alarm. It will display current definition and bitrate of current video input. And also display current audio input state.
Ｎｅｔ ＤＶＲ 4.9.3 Alarm Status Alarm status interface as follows: Display 4 kinds of alarm information of each channel: Sensor Alarm (Red mark), Motion Alarm (Yellow mark), Video lost (blue mark), Video Shield (Green mark). You can click the “Clear”button to close alarm sound in DVR front panel or in IR remote controller. Also you can click the “Alarm Clear”icon in DVR interface status bar to close alarm sound. 4.9.4 Online status Display the information which PC has login the DVR.
Ｕｓｅｒ Ｍａｎｕａｌ 4.9.5 Log Inquiry Log inquiry interface as follows: l Note: The log total number of the day which you inquired (Log information max support 1023 days, 524032 item logs); You can check the DVR host log information by web. l System log include: System boot up/Shut down log, firmware upgrade log, alarm log, PTZ control log, System user login log, System parameter change log, Record playback log, backup log, Formating HDD log, client login log. l System support backup log.
Ｎｅｔ ＤＶＲ 4.10 System Maintenance Open “Main Menu”-> “System Maintenance”to quick set and manage users etc., the interface is as follows: 4.10.1 Quick Settings You can quick set “Time setting”, “Network setting”, “HDD management”, “Input settings”, “Record parameter”and so on operations, please refer to “4.2 power on wizard”. Note: Please click “Save”button to save your parameter setting. 4.10.
Ｕｓｅｒ Ｍａｎｕａｌ 1. User Management l Add/delete user: Focus the cursor on the “Add”icon and click to add new user, move the cursor to select the user in the user list, then focus the cursor on the “Delete”icon and click to delete the user. l Modify password: Using the direction key of the remote controller to move the cursor to the user list, press “OK”, then you can get in the interface, or click the mouse to get in. l Support local and remote rights setting. 2.
Ｎｅｔ ＤＶＲ Encode Para.: Record mode (All); Encoding stream type (VBR); Definition (FD1); Bitrate (2M); Image quality (High); Frame rate (25fps); Audio (Enabled); Audio type (digital audio); pre-record time (10s); Alarm Delay-record time (30s); Enable schedule snapshot (Disable); Enable motion snapshot (Disable); Enable alarm snapshot (Disable); Snapshot period (1S); Snapshot number (1 pcs). Schedule record: Schedule record (Disable).
Ｕｓｅｒ Ｍａｎｕａｌ Ø The procedure is as follows: 1. Connect the Net DVR to PC by coherent network cable or LAN (pay attention to IP conflict). 2. Before upgrading, please confirm the IP address of host computer, input http://host IP:http port in browser address, download the webcontrol.exe and install then login. 3. After login then choose “Config” -> “Remote upgrade”to open upgrade interface. 4. Click “Browse”button to choose the file to be updated, and refer to the following figure. 5.
Ｎｅｔ ＤＶＲ 3. FTP upgrade Operation steps: 1. Open the FTP server software, configure it follow the setup wizard. Create user name and password in server. Set the root directory (the folder which will place upgrade file), set the permission (must set the download permission ). 2. Enter server after configuration. Set the FTP server IP and port. 3. Start FTP service. 4.
Ｕｓｅｒ Ｍａｎｕａｌ 4.11 Logout/Shutdown/Reboot To do Logout User, Shutdown, Restart operations by “Main Menu”-> “Shutdown”menu as below GUI: l Logout: Device will auto-lock after logout. l Shutdown: After you shutdown here, please click the power button in front panel to start up DVR. 4.12 Password Reset When user forget the DVR host administrator password, please recover password by following steps: 1. Shutdown DVR host. Cut off the power supply. 2. Remove the cover screws to open the case cover. 3.
Ｎｅｔ ＤＶＲ Appendix 1 IE Operation Instructions Notice: Please set firewall rank for low or medium, and surf software or net assistant software, etc. should be blocked or unloaded, otherwise the software may not run properly. Please guarantee to install DirectX 9.0 of Microsoft and confirm the Internet Explorer edition is 6.0 version or above. All hardware driver version should upgrade to the latest. 1.
Ｕｓｅｒ Ｍａｎｕａｌ 2. WAN Operation Instructions Step1: If there are fixed WAN IP address which could be given to the host DVR, you could connect DVR to WAN directly, set IP, subnet mask and gateway, then access normally. Step2: Connecting to WAN through PPPOE dialing. Step3: Access through the router forwarding. (When forwarding, the gateway should be set as current forwarding server. Note: forwarding instruction is for TCP protocol) IE access format: http://WAN IP:http port; http://Domain name:http port.
[3]Port Description: The command port is the TCP port of all DVRs communications, and HTTP port is IE browser port. Ｎｅｔ ＤＶＲ If you connect by static IP, you need set port mapping in your router. Take TP-LINK TL-480T model router for example: [1] After signing up routers, by choosing “Running Status”icon on left side menu of Figure 5, view the LAN IP and WAN IP address of the routers, such as, the LAN IP address 192.168.2.1, WAN IP address 116.30.143.163.
Ｕｓｅｒ Ｍａｎｕａｌ [3] Port Description: The command port is the TCP port of all DVRs communications, and HTTP port is IE browser port. Input the address like: http://116.30.141.49:http port. After a successful connection click “Download”button to download, and running control. Refresh the browser, then enter your user name and password to login in the login box (Figure 7). If login is successful, the interface will pop up as “Figure 8”. Figure 7 Figure 8 76 eLineTechnology.
Ｎｅｔ ＤＶＲ Appendix 2: Net DVR Q&A Thank you for choosing our DVR series products. We will always be at your services. In case you have any difficulty while using the products, please refer to the below frequently asked questions & answers. If you cannot find solution here, or the solution offered here still fails, please feel free to contact us by our hotline and/or technical support E-mail box. We will make most timely reply to your questions.
Ｕｓｅｒ Ｍａｎｕａｌ 04: Why does my system restart after self-check? 04: 1.Check the hard disks if they are in FAT32 file format, if not, change to FAT32. 2.Check Color System setting in Record Parameter menu. In case this setting is PAL, while present video input is in NTSC format, which will cause system restart. 3.Please unplug the network cable, to see whether DVRs run normally, since there are serious problems of the network which may also cause the host to restart repeatedly.
Ｎｅｔ ＤＶＲ 03: Why both the live display image and playback image are not showing the true color? 03: Please check if you have set the parameters well. (Please refer to chapter 4.7.3 for details) 04: Why my DVR displays distorted images on VGA monitor or cannot make full screen display? 04: 1.Please check if your VGA monitor is well set up. 2.Change your VGA monitor settings till make it full screen. 05: Why my DVR system shows disordered color? 05: 1.
Ｕｓｅｒ Ｍａｎｕａｌ NOTES: SDE72X3-B1218 80 eLineTechnology.
