User Manual

ManualsBrandsElite Screens ManualsProjector ScreensElite Screens - Aeon CineGrey 3D Series 100" Projector Screen - Black

V072415-EA www.elitescreens.com 1

Aeon Series

EDGE FREE® Fixed Frame Projection Screen

User’s Guide

Applies to all available screen materials: CineGrey 3D EDGE FREE® and CineWhite EDGE FREE®

Product Description: The Aeon Series is a fixed frame projection screen that uses Elite’s EDGE FREE™ technology.

The EDGE FREE® design resembles a giant size flat panel TV display. The Aeon includes a velvet tape as an

installation option to further enhance the frame appearance and absorb projector overshoot. An optional LED

backlighting kit is available for added visual appearance.

Assembly Video: For further assistance, watch our assembly and installation video at

www.elitescreens.com/video/aeon-assembly or scan the following QR Code:

For more information on the LED kit please visit: http://www.elitescreens.com/led

Hardware and Parts List

Please make sure all parts listed below are included before installation.

A. Elbow joint x 4 pcs

B. Top/Bottom horizontal fame x 4 pcs

C. Left/Right vertical frame x 2 pcs

D. Center joints x 2 pcs

E. Center Support bar x 1-2 pc

F. Wall brackets x2-3 pcs

G. M6 screw x 2-12 pcs

H. M5x15 screw x 24 pcs

I. M6x12 screw x 2-12pcs

J. M5x50 screws and anchor x 6 pcs

K. Rubber hammer x 1 pc

L. Screwdriver x1 pc

M. Velvet tape

N. Corner Support Bar (180”-200”) x4pcs

Summary of content (12 pages)

PAGE 1
Aeon Series EDGE FREE® Fixed Frame Projection Screen User’s Guide Applies to all available screen materials: CineGrey 3D EDGE FREE® and CineWhite EDGE FREE® Product Description: The Aeon Series is a fixed frame projection screen that uses Elite’s EDGE FREE™ technology. The EDGE FREE® design resembles a giant size flat panel TV display. The Aeon includes a velvet tape as an installation option to further enhance the frame appearance and absorb projector overshoot.
PAGE 2
Frame Assembly 1. Insert the center joint into one of the ½ horizontal frames (B) and fasten it with the two M5x15 screws (H). 2. Insert the other ½ horizontal frame piece to the center joint and fasten also using two M5x15 screws. 3. Repeat steps 1 and 2 for assembling the second horizontal frame. Push Push Center Joints Top right Frame Top left Frame Horizontal frame 4.
PAGE 3
6. Insert the two vertical short frames (C) into the elbow joint (A). push Horizontal long frame (B) push Vertical short frame (C) Vertical short frame (C) Note: For models 180” and above, ensure two M6 screws (G) are inserted on each vertical frame section before proceeding to step 7. Face Up 7. Join the remaining horizontal long frame (B) with the frame built in the previous steps as shown below. push V072415-EA Horizontal Long frame (B) www.elitescreens.
PAGE 4
8. Make sure all four corners are properly in place to form a perfect square. Then fasten the four angles with the M5x15 Screws (H). Four corners join correctly to form a perfect square. Use the included screwdriver (L) to fasten the Mx15 screws (H) into each corner by aligning the frame screw holes to the holes in the elbow joint (A). Screen Material Installation 1. Lay the screen material completely flat with the front facing down on a clean surface in a horizontal position.
PAGE 5
3. After all of the corners of the frame have been properly aligned, attach the material to the frame in the following order A→B→C→D (see instructions below for details). D A D C B Attach the screen material to the corners as shown below. 1) Stretch the screen material in the direction of the arrowhead. 2) Fold over and attach material to the velcro strip of the frame. 3) Fold over second side and attach to frame 4) Repeat until all four sides are done in the order A, B, C, D 4.
PAGE 6
5. Proceed to attach the rest of the material to the frame as described in the illustrations below. Grasp the middle of the screen material and attach it to the velcro strip on the frame Lay the Velcro end on the screen material over the Velcro end of the frame and keep it within the edge. Proceed in the following sequence below ①② The key is to attach within the middle sections of 1 and 2. Then continue attaching the remaining unattached areas.
PAGE 7
Screen Material Removal Follow the steps to properly remove the screen material from the frame. This procedure will ensure prolonging the life of the screen material. 1. Detach the velcro from the frame. 2. Gently pull back the material to release the material from the velcro connections on the corners Pull back the screen material from the velcro connection along the edges of the frame to detach it. Support bar installation (for models under 180”): 1.
PAGE 8
Support bar installation (for models 180” and above): 1. Position the center support bars (E) and M6 Hex screws (G) in the areas of the frame shown below in fig. 1. Align the holes on each end of the support bars with the M6 hex screws (G) located at the top and bottom frame sections. Then fasten with the M6x12 screws (I). Move the M6 hex screw (G) to these areas of the frame. Center Support Bar Align the M6 Screws with the two holes located on the Center Support Bar.
PAGE 9
Align the M6 screws with the two holes on the Corner Support Bars. Figure 2 Notice to Installer: These instructions only apply if you have the CineGrey 3D ALR material. Please use the following installation instructions to obtain superior optical performance from the Angular Reflective ALR (Ambient Light Rejecting) Screen. Projector Ceiling Installation: Make sure the projector (light in) is angled (ϴ1) to reflect (ϴ2) at the mirror-opposite angle (light out) to align with the viewer’s eye level.
PAGE 10
Velvet Tape Trim Installation Attention: Installing the velvet trim will reduce the viewing size of your screen. See below illustrations for a comparison of the viewing size of the before and after edge trim installation using the 100” & 120” 16:9 diagonal models. 100” comparison: Before installing the trim strip After installing the trim strip 120” comparison: After installing the trim strip Before installing the trim strip 1) Lay the assembled frame on its back on a clean surface.
PAGE 11
3) Make a light mark with a pencil approximately every 8-10 inches apart. This will help guide the way to making a straight line for the velveteen strip. 10” 10” 4) Repeat steps 2 and 3 on the remaining sides 5) Peel off the backing on the velvet strip and align the top edge at the 10 mm mark. Screen Material Screen Material 10” 6) Continue peeling off the backing until the other side has been reached. Make sure that the velvet strip is kept straight the entire way.
PAGE 12
Installation Locate your desired installation location with a stud finder (recommended) and mark the drill-hole area of where the screen is to be installed. 1. Drill a hole with the proper bit size according to the wood screws included. 2. Line up the wall brackets with the drilled holes on the installation location and screw them in using a Phillips screwdriver. 3. Position the frame screen onto the wall brackets (F) as shown in below. 4.