Owner Manual

ManualsBrandsElite Screens ManualsFurnitureAeon CLR Series White Fixed Frame Wall/Ceiling Mounted Projector Screen

Table Of Contents

Assembly Video Watch our assembly video on-line at www.elitescreens.com/video/aeon-ust-assembly or scan the QR code

110315-JA www.elitescreens.com 1

Aeon CLR™ Series

EDGE FREE® Fixed Frame Screen w/ StarBright CLR™

(Ceiling Light Rejecting) Front Projection Material

User’s Guide

Product Description:

The Aeon CLR™ Series is an ultra-short throw fixed frame projection screen that uses Elite’s EDGE FREE®

technology. It is designed for with Ultra-Short Throw Projectors only, for use in environments where ceiling light

cannot be entirely controlled. It includes an LED backlight kit and a bezel trim to further enhance the frame appearance.

Screen Maintenance

Dust, dirt and scratches on the projection screen surface will affect the quality and performance of the projection image.

For optimal results we advise to pay attention to the following instructions.

1) The screen surface has a horizontal structure. DO NOT wipe the screen up and down or in a circular motion.

Wipe from left to right only.

2) Please clean the dust on the screen surface with a soft brush or microfiber cloth (rough towel or cloth may damage

the screen’s surface).

3) Gently wipe the screen with a moistened microfiber cloth with mild soap diluted in water.

Notes：

The following precautions should be followed at all times to avoid damaging the material, which is not

covered under warranty.

 Don’t touch the screen material to avoid leaving fingerprints. Use gloves when handling the material.

 Don’t scratch the material, as it will leave permanent markings on the screen’s surface.

 Don’t point to the screen material with a fingertip or other sharp objects to prevent damage to the material.

 Don’t use acetone, benzene, alcohol and any other organic solvents to clean the screen material. Using such

chemicals will permanently damage the screen.

Assembly Video

Watch our assembly video on-line at

www.elitescreens.com/video/aeon-ust-assembly

or scan the QR code

Summary of content (11 pages)

PAGE 1
Aeon CLR™ Series EDGE FREE® Fixed Frame Screen w/ StarBright CLR™ (Ceiling Light Rejecting) Front Projection Material User’s Guide Product Description: The Aeon CLR™ Series is an ultra-short throw fixed frame projection screen that uses Elite’s EDGE FREE® technology. It is designed for with Ultra-Short Throw Projectors only, for use in environments where ceiling light cannot be entirely controlled. It includes an LED backlight kit and a bezel trim to further enhance the frame appearance.
PAGE 2
Hardware and Parts List Please make sure all parts listed below are included before installation. A. Elbow joint x4 pcs B. Top/Bottom horizontal frame x C. Left/Right vertical frame x 2 pcs D. Center joints x 2 pcs 4 pcs E. Center support bar x 1-2 pcs F. Wall brackets x2-3 pcs G. M6 screw x 2-4 pcs H. M5x15 screw x 24 pcs I. M6x12 screw x 2-4 pcs J. Screw and anchor x 6-9 pcs K. Rubber mallet x 1 pc L. Screw driver x 1 pc M. Black Tape x1bag N. Bezel trim x6 pcs O. Corner sleeve x 4 pcs P.
PAGE 3
5. Insert the elbow joint (A) into each end of the horizontal frames (B) as shown below. Elbow Joint (A) Elbow Joint (A) Horizontal long frame (B) Push 6. Insert the two vertical short frames (C) into the elbow joint (A). push Horizontal long frame (B) push Vertical short frame (C) 7. Join the remaining horizontal long frame (B) with the frame built in the previous steps as shown below. Horizontal Long frame (B) Push 110315-JA Push www.elitescreens.
PAGE 4
8. Make sure all four corners are properly in place to form a perfect square. Then fasten the four angles with the M5x15 Screws (H). Four corners join correctly to form a perfect rectangle. Use the included screwdriver (L) to fasten the Mx15 screws (H) into each corner by aligning the frame screw holes to the holes in the elbow joint (A).
PAGE 5
4. Carefully and gently place the assembled frame on top of the screen material as shown below. Make sure to not allow the angle edge of the frame to come in direct contact with the material to avoid puncturing or damaging it. Velcro Screen material back facing up 5. After all of the corners of the frame have been properly aligned (example D), attach the material on the frame in the following order A→B→C→D (see instructions below for details).
PAGE 6
. After all four corners have been attached; please check whether the screen material wraps the frame corners. If not, please loosen the Velcro connection and repeat the above steps so the frame is not exposed. Note: The black shaded part represents the Velcro on the Note: frame. That Velcro end will Represents the ultimately attach with the screen material other Velcro end on the screen material. 7. Proceed to attach the rest of the material to the frame as described in the illustrations below.
PAGE 7
Screen Material Removal Follow the steps to properly remove the screen material from the frame. This procedure will ensure prolonging the life of the screen material. 1. Detach the Velcro from the frame. 2. Gently pull back the material to release the material from the Velcro connections on the corners Pull back the screen material from the Velcro connection along the edges of the frame to detach it. Support bar installation: 1.
PAGE 8
Edge trim Installation Included is an black edge trim that provides an elegant ultra-thin bezel finish Edge trim x 6 PCS Plastic corner sleeve x4pcs Black tape x1pcs 1. Place the assembled frame on a flat and clean surface. The projection screen surface should be facing up. Align the tape with the edge of the screen, as shown in Figure 1. Once properly aligned, apply the black tape to the center of the top and bottom of the screen material.
PAGE 9
3. After properly aligning all trim pieces, carefully remove trim piece A (see Figure 3 below). Remove the inside backing of the tape and place the trim piece in its original position on the frame. Repeat this step for the remaining trim pieces in the following order: B-C-D-E-F. A B F C D E Figure 3 The front side of the frame with trim pieces attached 4. After the bezel trim has ben installed, place a corner sleeve (O) on all four corners.
PAGE 10
Notice to Installer: The StarBright CLR ™ is exclusively for table-mounted ultra-short throw projectors as illustrated in the Example 2 diagram. Overhead placement or a standard projector will make the image very dark, on account of the screen’s absorbent layer deflecting light that is not aligned with its reflective angle. Please use the following installation instructions to obtain superior optical performance from the Retro-Reflective ALR (Ambient Light Rejecting) Screen.
PAGE 11
Installation 1. Correctly distinguish the top and bottom of the screen： Place the assembled screen vertically on the ground. Look down on the screen, if the material is black it is in the correct direction and ready for mounting on the wall. However, if the material is white, turn around the screen and then install it. Note: There are also “Top” and “Bottom” labels on the back of the screen material to help distinguish the correct direction. Please make a note of this. 2.