User Manual

ManualsBrandsElite Screens ManualsProjector ScreensElite Screens - SableFrame 100" Projector Screen - Velvet black

Rev.5/17/2016 DR www.elitescreens.com 1

Sable Frame Series

Fixed Frame Projection Screen

Featuring CineGrey 3D Ambient Light Rejecting Material

User’s Guide

Congratulations on your new Sable Frame purchase! The screen material included is our ISF certified CineGrey

3D, which is a reference quality front projection material, precisely formulated for environments with minimal

control of ambient lighting. It was designed to enhance picture brightness, offer accurate color fidelity, and

improve contrast levels. The CineGrey 3D is best for family rooms, educational facilities, conference rooms or

any applications in which ambient light is a factor.

In order for the CineGrey 3D to maintain its surface quality and optimal performance, please refer to the list below

for proper maintenance and cleaning:

 Use a dry microfiber cloth to remove dust from the screen’s surface.

 When cleaning, use a damp microfiber cloth with warm water to remove any marks.

 Never rub or apply pressure when cleaning the surface.

 Never attempt to use any solutions, chemicals or abrasive cleaners on the screen surface.

 In order to avoid damaging the screen, avoid touching it directly with your fingers, pens/pencils or any

other sharp or abrasive objects.

Hardware and Parts List

1. Frame Parts x 6pcs

(4 top/bottom horizontal frame pcs + 2 side vertical frame pcs)

7. M5x50 wood screws x 6 pcs

2.Tension Rods x 6pcs

(4 top/bottom rods + 2 side rods)

8. Hollow wall anchor x 6 pcs

3. Screen Material x 1pc

9. M5x15 screws x 16 pcs

4. Center joints x 2pcs

10.Center Support Bar x 1 – 2 pcs

(depending on model/size)

5. Elbow Joints x 4pcs

11. Support joiner x 2 – 4 pcs

(depending on model/size)

6. Wall brackets x 2 – 3pcs

(depending on model/size)

12. Fix Plates x 60 – 180 pcs

(depending on model/size)

Note: Please make sure all parts are included in your package before assembling the fixed frame screen.

Summary of content (8 pages)

PAGE 1
Sable Frame Series Fixed Frame Projection Screen Featuring CineGrey 3D Ambient Light Rejecting Material User’s Guide Congratulations on your new Sable Frame purchase! The screen material included is our ISF certified CineGrey 3D, which is a reference quality front projection material, precisely formulated for environments with minimal control of ambient lighting. It was designed to enhance picture brightness, offer accurate color fidelity, and improve contrast levels.
PAGE 2
FRAME ASSEMBLY 1. Insert the center joint connector into to one of the 1/2 horizontal frames and fasten it with two M5x15 screws. M5×15 screws ½ Horizontal Frame Beveled Track 2. Insert the other 1/2 horizontal frame piece to the center joint connector and fasten it with two M5x15 screws. Repeat steps 1 and 2 for assembling the second horizontal frame. ½ Long Frame Push Beveled Track Horizontal Long Frame Note: Do not tighten the screws completely until all frame pieces have been properly aligned. 3.
PAGE 3
Push Push Short frame Short frame Screw M5×15 screws (Fig.1.2) 4. Join all four frame parts together following the steps shown below. (Fig.2) Note: When assembling, please push simultaneously both ends of the long frames. Insert the exposed ends of the joint connectors into the short (vertical) frame and align the four corners so that they meet at perfect right angles Push Push M5×15 screws Screw ( fig.2) Rev.5/17/2016 DR www.elitescreens.
PAGE 4
Attaching the screen material to the frame 1. Make sure the area where the screen material and frame will be placed is a clean, dry, and non-abrasive surface. 2. Carefully unroll the material inside the frame. (Fig.3) Please note the material will be noticeably smaller than the frame, as the material must be stretched to create a sufficient amount of tension for perfect material flatness. Notes  Make note of the label that distinguishes the backside from the front side.  (Fig.
PAGE 5
(3) Stretch the material to the corner and insert the screen material’s edge into the groove of the frame. While one hand holds the material in place, the other hand snaps in the push plate (Fig.7-Fig.8) Insert push plate in (Fig. 7) Plate Frame groove Screen material edge (Fig. 8) Schematic cross section of the frame Tip for attaching the last corner (D): 1. Position yourself to the left ① . ② Pull 2.
PAGE 6
(6) Fasten the remainder of the fix plates in the empty locations in the red markings to complete attaching the screen material. (Fig.12) (Fig.12) Center Support Bard 1. Insert the support joiner into each end of the center support bar to complete assembly. support joiner Center support bar 2.
PAGE 7
Notice to Installer: Please use the following installation instructions to obtain superior optical performance from the CineGrey 3D Angular Reflective ALR (Ambient Light Rejecting) Screen. Make sure to follow these instructions in order for the CineGrey 3D to perform correctly. •Angular-Reflective material is not compatible with ultra/short-throw projectors •Minimum lens throw ratio 1.
PAGE 8
Installation 1. Locate your desired installation location with a stud finder (recommended) and mark the drill-hole area of where the screen is to be installed. 2. Drill a hole with the proper bit size according to the wood screws included. 3. Line up the wall brackets with the drilled holes on the installation location and screw them in using a Phillips screwdriver. Note: Use 2 top wall brackets on diagonal sizes below 135”, and use 3 top wall brackets on diagonal sizes 135” and above. 4.