User`s guide

ManualsBrandsElite Screens ManualsProjectorsezFrame

Rev.091912-JA

www.elitescreens.com info@elitescreens.com

Elite ezFrame/Cinema235 &

Sable Frame Series

Fixed Frame Projection Screen

User’s Guide

Hardware and Parts List

1. Frame Parts x 6 pcs (4 top/bottom frame pcs. + 2 side frame pcs)

2. Tension Rods x 6 pcs (4 top/bottom rods + 2 side rods)

3. Screen Material x 1 pc

4. Center joints x 2 pcs

5. Elbow Joints x4pcs

6. Wall brackets x2 – 3 pcs (depending on model/size)

7. M5x50 wood screws x 6 pcs

8. Hollow wall anchor x 6 pcs

9. M5x15 flat head screws x 16 pcs

10. Center Support Bar x 1 – 2 pcs (depending on model/size)

11. Support joiner x 2 – 4 pcs (depending on model/size)

12. Fix Plates x 30 – 90 pcs (depending on model/size)

Note: Please make sure all parts are included in your package before proceeding to assemble your Elite

Screens fixed frame projection screen.

FRAME ASSEMBLY

1. Insert the center joint connector to the horizontal frame piece and then fasten it with two Mx15 flat head screws.

Summary of content (8 pages)

PAGE 1
Elite ezFrame/Cinema235 & Sable Frame Series Fixed Frame Projection Screen User’s Guide Hardware and Parts List 1. Frame Parts x 6 pcs (4 top/bottom frame pcs. + 2 side frame pcs) 2. Tension Rods x 6 pcs (4 top/bottom rods + 2 side rods) 3. Screen Material x 1 pc 4. Center joints 5. Elbow Joints x 2 pcs x4pcs 6. Wall brackets x2 – 3 pcs (depending on model/size) 7. M5x50 wood screws x 6 pcs 8. Hollow wall anchor 9. M5x15 flat head screws 10.
PAGE 2
. Insert the other horizontal frame piece to the center joint connector and then fasten it with two Mx15 flat head screws. ½ Long frame Push Please do not secure the screws completely until the frames pieces have been lined up correctly. 3. Insert both elbow joint connectors into the long horizontal frame (see fig.1) 2 Rev.091912-JA www.elitescreens.com info@elitescreens.
PAGE 3
4. Join all four frame parts together following the steps shown below. (fig.2) Insert the exposed ends of the joint connectors into the short (vertical) frame and align the four corners so that they meet at perfect right angles Push Push ( fig.2) 5. After making sure that all four corners join at right angles to form a perfect rectangle, fasten the four angles together by using the (x8) Mx15 flat head screws included.(see fig.3) 3 Rev.091912-JA www.elitescreens.com info@elitescreens.
PAGE 4
Attaching the screen material to the frame 1. Lay out the screen and tension rods on a clean and dry surface. Insert the screen tension rods through the sleeves according to their corresponding lengths on each edge of the screen as shown below. (see fig.4) Tension Rod (Horizontal) x 4 Tension Rod (Vertical) x 2 Screen Push Tension Rod (horizontal) Steel Rodrod Rodrod Steel Push Tension Rod (Vertical) Push ( fig.4) 2.
PAGE 5
Black backing for AcousticPro models This procedure only applies to AcousticPro models. Disregard this section if your Fixed Frame does not include an acoustic transparent screen material. The purpose of the black backing material is to block out any light penetration that may reflect off of anything mounted behind the screen, which can cause distortion to the projected image. The black backing is held in place by the Velcro that is on the fix plates. Black backing （fig.
PAGE 6
Attaching the Fix Plates___ 1. Make sure that the material and frame are both lying face down on a clean, dry and non-abrasive surface. 2. Center the material inside the frame. Please note that the material will be noticeably smaller than the frame. The size differential is needed in order to be able to stretch the material as you attach it to the frame so that the end result is a flat viewing surface. 3.
PAGE 7
3. Slide the top end of the bar into the top center point of the frame to complete the center support bar installation. This will provide added stability to your frame and added tension to the material. Center Support Bar (Fig. 8) Installation 1. Locate your desired installation location with a stud finder (recommended) and mark the drill-hole area of where the screen is to be installed. 2. Drill a hole with the proper bit size according to the wood screws included. 3.
PAGE 8
CAUTION Please follow these instructions carefully to ensure proper maintenance and safety with your Fixed Frame Screen 1. When hanging the screen up, please make sure that no other objects such as power switches, outlets, furniture, ladders, windows, etc. occupy the space designated for your Fixed-Frame screen. 2.