Owner manual

ManualsBrandsElite Screens ManualsMultimediaezFrame2 Series

Rev.041114-JA www.elitescreens.com 1

ezFrame &

Sable Frame Series

Fixed&Frame&Projection&Screen&

User’s&Guide&(V.2)&

Hardware and Parts List

1. Frame Parts x 6 pcs (4 top/bottom frame pcs + 2 side frame pcs)

2. Screen Material x 1 pc

3. Center joints x 2 pcs

4. Elbow Joints x4pcs

5. Wall brackets x4pcs (depending on model/size)

6. Drywall anchor/Wood Screw x 6 pcs

7. Drywall anchor x 6 pcs

8. M5x15 flat screws x 16 pcs

9. Center Support Bar x 1 – 2 pcs (depending on model/size)

10. Support joiner x 2 – 4 pcs (depending on model/size)

11. Fix Plates x 60 – 180 pcs (depending on model/size)

12. Rubber hammer x 1 PCS

13．Screw driver x 1 PCS

Note:&Please&make&sure&all&parts&are&included&in&your&package&before&proceeding&to&assemble&your&Elite&Screens&

fixed&frame&pro jectio n&scre en. &

FRAME ASSEMBLY

1. Insert the center joint connector to the ½ horizontal frame piece and fasten it with two M5x15 screws.

bevel connection

½ Long Frame

M5×15 Screw

Summary of content (7 pages)

PAGE 1
ezFrame & Sable Frame Series Fixed Frame Projection Screen User’s Guide (V.2) Hardware and Parts List 1. Frame Parts x 6 pcs (4 top/bottom frame pcs + 2 side frame pcs) 2. Screen Material x 1 pc 3. Center joints 4. Elbow Joints x 2 pcs x4pcs 5. Wall brackets x4pcs (depending on model/size) 6. Drywall anchor/Wood Screw 7. Drywall anchor x 6 pcs x 6 pcs 8. M5x15 flat screws 9. Center Support Bar x 16 pcs x 1 – 2 pcs (depending on model/size) 10.
PAGE 2
. Insert the other ½ horizontal frame piece to the center joint connector and fasten it with two M5x15 head screws. Repeat steps 1 and 2 for assembling the second horizontal frame. M5x15 screws ½ Long Frame Push Bevel connection Horizontal Long Frame Note: a. Two ½ size horizontal frames should be assembled for a screen. b. Do not tighten the screws completely until all frame pieces have been assembled correctly. 3.
PAGE 3
Join all four frame parts together following the steps shown below. (Fig.2) Note: When assembled, please push simultaneously the two ends of the long frames. 4. Insert the exposed ends of the joint connectors into the short (vertical) frame and align the four corners so that they meet at perfect right angles Push Push M5×15 screws Screw ( fig.2) Attaching the screen material to the frame ( fig.3) 1.
PAGE 4
Insert push plate in Plate Frame groove Screen material edge (Fig. 4) (Fig. 5) Schematic cross section of the frame (2) Begin by securing the four corners in the following sequence A→B→C→D (Fig.6). (3) Insert the fix the plates as shown on Fig. 5. Fix plate ① is about 10cm away from the frame’s corner. Fix plate ② is about 5cm away. (Fig.7) A C (Fig. 7) (Fig. 6) B D Tip for attaching the last corner (D): 1.
PAGE 5
(5) Next, fasten a fix plate on the center of each frame side in the following order I→J→K→L→M→N→O→P as shown in Fig.10. I P O J (Fig.10) K N L M (6) Fasten the remainder of the fix plates in the empty locations in the red markings to complete attaching the screen material. (Fig.11) (Fig.11) Black backing for AcousticPro models This procedure only applies to AcousticPro models. Disregard this section if your Fixed Frame does not include an acoustically transparent screen material.
PAGE 6
Center Support Bard 1. Insert the support joiner into each end of the center support bar. support joiner Center support bar 2. Insert the Center Support Bar into the upper top groove on the back of the frame (not the one where the fix plate inserts) with the bottom end near the approximate center point of the frame and rotate it in at an angle so that both ends of the bar are in alignment with the groove (see Fig. 16 and Fig. 17 below for details).
PAGE 7
Installation 1. Locate your desired installation location with a stud finder (recommended) and mark the drill-‐hole area of where the screen is to be installed. 2. Drill a hole with the proper bit size according to the wood screws included. 3.