User Manual

ManualsBrandsElite Screens ManualsProjector ScreensElite Screens - EzFrame Series 110" Projector Screen - Black

Rev.041014-JA www.elitescreens.com 1

ezFrame &

Sable Frame Series

Fixed&Frame&Projection&Screen&

User’s&Guide&

Hardware and Parts List

1. Frame Parts x 6 pcs (4 top/bottom horizontal frame pcs + 2 side vertical frame pcs)

2. Tension Rods x 6 pcs (4 top/bottom rods + 2 side rods)

3. Screen Material x 1 pc

4. Center joints x 2 pcs

5. Elbow Joints x 4 pcs

6. Wall brackets x 2 – 3 pcs (depending on model/size)

7. M5x50 wood screws x 6 pcs

8. Hollow wall anchor x 6 pcs

9. M5x15 screws x 16 pcs

10. Center Support Bar x 1 – 2 pcs (depending on model/size)

11. Support joiner x 2 – 4 pcs (depending on model/size)

12. Fix Plates x 60 – 180 pcs (depending on model/size)

Note: Please make sure all parts are included in your package before proceeding to assemble your Elite

Screens fixed frame projection screen.

FRAME ASSEMBLY

1. Insert the center joint connector into to one of the 1/2 horizontal frames and fasten it with two M5x15 screws.

bevel connection

½ Horizontal Frame

M5×15 screws

Summary of content (7 pages)

PAGE 1
ezFrame & Sable Frame Series Fixed Frame Projection Screen User’s Guide Hardware and Parts List 1. Frame Parts x 6 pcs (4 top/bottom horizontal frame pcs + 2 side vertical frame pcs) 2. Tension Rods x 6 pcs (4 top/bottom rods + 2 side rods) 3. Screen Material x 1 pc 4. Center joints 5. Elbow Joints x 2 pcs x 4 pcs 6. Wall brackets x 2 – 3 pcs (depending on model/size) 7. M5x50 wood screws 8. Hollow wall anchor 9. M5x15 screws x 6 pcs x 6 pcs x 16 pcs 10.
PAGE 2
. Insert the other 1/2 horizontal frame piece to the center joint connector and fasten it with two M5x15 screws. Repeat steps 1 and 2 for assembling the second horizontal frame. ½ Long Frame Push bevel connection Horizontal Long Frame Note: a. 2 long frames should be assembled for a screen. b. Do not tighten the screws completely until all frame pieces have been assembled correctly. 3. Insert both elbow joint connectors into the long horizontal frame and then fasten it with two M5x15 screws (see Fig.
PAGE 3
Join all four frame parts together following the steps shown below. (Fig.2) Note: When assembled, please push simultaneously the two ends of the long frames. 4. Insert the exposed ends of the joint connectors into the short (vertical) frame and align the four corners so that they meet at perfect right angles Push Push M5×15 screws Screw ( fig.2) Attaching the screen material ( fig.3) to the frame 1.
PAGE 4
2. Make sure that the material and frame are both lying face down on a clean, dry, and non-abrasive surface. 3. Center the material inside the frame. Please note the material will be noticeably smaller than the frame, as the material must be stretched to create a sufficient amount of tension for perfect material flatness. 4. Attach the fix plates (1) Begin by securing the four corners in the following order A→ B→ C→ D (Fig.4) (2) Insert the fix plates as shown on Fig. 5.
PAGE 5
(5) Put the next set of fix plates ② in the middle between fix plate ① and the corner. (Fig.9) (Fig.9) (6) Then put the next set of fix plates ③ between ①and ② and the corner. (Fig.10) (Fig.10) (7) Lastly, put the next set of fix plates (4) as shown in Fig.11 (Fig.11) (8) Repeat steps 5-7 to for the rest of the sides to complete attaching the screen material (Fig.12) (Fig.12) Black backing for AcousticPro models This procedure only applies to AcousticPro models.
PAGE 6
Center Support Bard 1. Insert the support joiner into each end of the center support bar to complete assembly. support joiner Center support bar 2. Insert the Center Support Bar into the upper top groove on the back of the frame (not the one where the fix plate inserts) with the bottom end near the approximate center point of the frame and rotate it in at an angle so that both ends of the bar are in alignment with the groove (see Fig. 17 and Fig. 18 below for details).
PAGE 7
Installation 1. Locate your desired installation location with a stud finder (recommended) and mark the drill-hole area of where the screen is to be installed. 2. Drill a hole with the proper bit size according to the wood screws included. 3. Line up the wall brackets with the drilled holes on the installation location and screw them in using a Phillips screwdriver. Note: Use 2 top wall brackets on diagonal sizes below 135”, and use 3 top wall brackets on diagonal sizes 135” and above. 4.