Manual

ManualsBrandsElite Screens ManualsAudio Visual PresentationezFrame 2 80.9 x 143.8" Fixed Frame Projection Screen

Rev.081914-JA www.elitescreens.com 1

ezFrame 2 &

Sable Frame 2 Series

Fixed Frame Projection Screen

User’s Guide

Thank you for choosing an Elite Screens fixed frame projection screen! Please read through this user guide before

utilizing the screen. Correct usage and maintenance will ensure a long product life.

Care & Use Instructions

Dust, dirt and scratches on the projection surface will affect the picture quality, please take note of the points

below to prevent that from occurring:

1. Do not touch the projection surface with your hands

2. Do not write or draw on the projection surface

3. Do not use fingers or sharp objects to point on the projection surface; this will damage the screen

material.

4. Use a soft-damp cloth to clean the projection surface; do not use chemical cleaning agents or

alcohol.

5. Use clean water when dampening the cleaning cloth and do not rub against the material to clean it.

Hardware and Parts List

A. Frame Parts

x 6 pcs (4 top/bottom frame pcs + 2 side frame pcs)

B. Screen Material

x 1 pc

C. Center joints

x 2 pcs

D. Elbow Joints

x4 pcs

E. Wall brackets

x4 pcs (depending on model/size)

F. Wood Screws

x 8 pcs

G. Drywall anchors

x 8 pcs

H. M5x15 screws

x 16 pcs

I. Center Support Bar

x 1 - 2 pcs (depending on model/size)

J. Support joiner

x 2 - 4 pcs (depending on model/size)

K. Fix Plates

x 60 - 180 pcs (depending on model/size)

L. Rubber hammer

x 1 pc

M. Screw driver

x 1 pc

Note: Please make sure all parts are included in your package before proceeding to assemble your fixed frame

projection screen.

Summary of content (8 pages)

PAGE 1
ezFrame 2 & Sable Frame 2 Series Fixed Frame Projection Screen User’s Guide Thank you for choosing an Elite Screens fixed frame projection screen! Please read through this user guide before utilizing the screen. Correct usage and maintenance will ensure a long product life. Care & Use Instructions Dust, dirt and scratches on the projection surface will affect the picture quality, please take note of the points below to prevent that from occurring: 1. Do not touch the projection surface with your hands 2.
PAGE 2
FRAME ASSEMBLY 1. Insert the center joint (c) connector to the ½ horizontal frame piece and fasten it with two M5x15 screws (h). ½ Long Frame M5×15 Screw bevel connection 2. Insert the other ½ horizontal frame piece to the center joint (c) connector and fasten it with two M5x15 screws (h). Repeat steps 1 and 2 for assembling the second horizontal frame. M5x15 screws ½ Long Frame Push Bevel connection Horizontal Long Frame Note: a. Two½ size horizontal frames should be assembled for a screen. b.
PAGE 3
Screw M5x15Screws Push Push Short frame Short frame (Fig.1.2) ( fig.3) 4. Join all four frame parts together following the steps shown below. (Fig.2) Note: When assembled, please push simultaneously the two ends of the long frames. Insert the exposed ends of the joint connectors into the short (vertical) frame and align the four corners so that they meet at perfect right angles Push Push M5×15 screws Screw ( fig.2) Rev.081914-JA www.elitescreens.com ( fig.
PAGE 4
Attaching the screen material to the frame 1. Make sure the screen material and frame are both lying face down on a clean, dry, and non-abrasive surface. 2. Carefully unroll the material inside the frame. (Fig.3) Please note the material will be noticeably smaller than the frame, as the material must be stretched to create a sufficient amount of tension for perfect material flatness. Notes： (Fig.3)  Make note of the label to help distinguish the back and front side.
PAGE 5
Tip for attaching the last corner (D): 1. Position yourself left of location ①. 2. Pull the material to the corner of the frame with your hand while your left ③ Pull hand snaps in the fix plate on location ①(the third red dot). ④ 3. Then insert and snap in the fix plate on location②. 4. Next, move and position yourself on location ③，then pull the edge to the frame and fasten plates on locations③and④. ① 5. Finally, fasten the last fix plate on location⑤. (Fig.8) ② ⑤ (Fig.
PAGE 6
Black backing for AcousticPro models This procedure only applies to AcousticPro models. Disregard this section if your Fixed Frame does not include an acoustically transparent screen material. The purpose of the black backing material is to block out any light penetration that may reflect off of anything mounted behind the screen, which can cause distortion to the projected image. The black backing is held in place by the Velcro that is on the fix plates.
PAGE 7
Diagonal models above 135” require 2x Center Support Bars (Fig. 17) 3. Slide the top end of the bar into the top center point of the frame to complete the center support bar installation. This will provide added stability to your frame and added tension to the material. Installation 1. Locate your desired installation location with a stud finder (recommended) and mark the drill-hole area of where the screen is to be installed. 2.
PAGE 8
CAUTION Please follow these instructions carefully to ensure proper maintenance and safety of your Fixed Frame Screen. 1. When hanging the screen up, please make sure that no other objects such as power switches, outlets, furniture, ladders, windows, etc. occupy the space designated for your Fixed-Frame screen. 2.