Raptor/Raptor Tension Series Electric Floor Rising Front Projection Screen User’s Guide Rev. 031210-JA www.elitescreens.com info@elitescreens.
Components List A (Base) BCD (Partitions) E (Support) F (Veneer) GH (Sides) IJ (Doors) KLMN (Back) O (Cover) P (Cover) QR (Layer) Hardware Pack Connecting Bolt X 37 Connector Housing X 37 Shelf Support (nog) X 8 Screw X 8 Controllers IR (Infrared) Remote Control 3-way Wall Switch (RJ45 Connection) RF (Radio Frequency) Remote Control 1 AA Batteries
Required Tool Phillips Head Screwdriver Use of connecting bolts when assembling the components Step1: Use a Phillips Head Screwdriver to attach the Connecting Bolt to the furniture components (unit-A). Step2: Insert the exposed section of the connecting bolt on (unit-A) into the hole on the side-edge of (unit-B). Insert the Connector Housing (Phillips cross head out) into the hole of (unit-B).
Operation The screen module (component-P) can be used by itself on a flat, level surface or it can be combined with Elite’s Raptor media stand housing as a fully assembled product. The power connection is located on the screen module’s rear right-hand leg support and feeds conveniently through the cabinet housing to its designated power source. The screen may be operated using the IR, RF, or 3-way wall switch.
Assembly Step 1. Attach the Connecting Bolts to fixed to the base (component-A). Then attach the partitions (components-B, C and D) via the connecting bolts as described on page 2. X 6PCS X 6pcs X 6pcs 2. Install the Support (component-E) using the connecting bolts and housings.
3. Veneer (component-F) Installation. F X 6pcs X 2pcs 4. Attach the Side boards (components-G & H) to the Base and Veneer (components-A & F). X 2pcs X 12pcs 5. Lock the Connector Housings to secure the media stand’s body.
6. Turn over the media stand and lock the connector housings on the bottom. X 8pcs 7. Attach the doors with the concealed hinges and install the back panels (components-K,L,M and N) using the grooves in (components-G, B, C, D, & H).
. Install the Cover (component-O) and lock with the connector housings. X 10pcs X 10pcs 9. Put the screen module (component-P) into the assembled media stand. It must align with the shelf supports (see enlarged image below) for a sccure fit and proper installation.
10. Shelf installation: (adjustable) The shelf supports (nogs) have variable height placements. X 8pcs 11. Complete Infrared-Sensitive Safety Device (ISSD) This is a safety feature to prevent injuries caused by fingers, hair, etc. getting caught up in the screen’s closing mechanism. If the small infrared light beams are obstructed, the screen closing operation will halt immediately.
Caution 1. The stand should only be cleared up by dry wipes appropriate for furniture care. 2. The screen material may be cleaned with a damp cotton cloth but caution should be taken to avoid getting moisture down into the rolled material or mechanical functions of the screen. 3. For optimal product longevity, put the screen in the down (closed) position when not in use. 4. Avoid touching the screen material either with fingers or any other foreign objects (Exception, see #2. Cleaning methods). 5.
Warranty Policy *Valid in the US and Canada only Two (2) year warranty parts and labor from defects in workmanship from purchase date as follows. Three (3) year parts and labor warranty from defects in workmanship for GEMR (Government, Educational, Military, & Religious) purchases of new product only Each party will be responsible for one way shipping during the warranty period. (Different policy for DOA, see next.
Contact Info US & Canada Tech Support & Warranty Claim Please contact us at service@elitescreens.com or call +1 877-511-1211 #3 Service Europe Tech Support & Warranty Claim Please contact us at service@elitescreens.eu or call +49-(0) 40-30392958 Asia Tech Support & Warranty Claim Please contact us at service@elitescreens.com.cn or call +86-(0) 755-8461-7989 Taiwan Tech Support & Warranty Claim Please contact us at service@elitescreens.com.