Application Guide

ManualsBrandsElite Screens ManualsElectronicsTripod B, 71-INCH 1:1, Lightweight Pull Up Foldable Stand, Manual, Movie Home Theater Projector Screen, 4K / 8K Ultra HDR 3D Ready, 2-YEAR WARRANTY

Elite Screens Frequently Asked Questions

Screens FAQs

Q1: How can I extend my RJ-45 accessory such as my 3-way wall switch, 5-12v trigger, and IR "eye" sensor?

A: You can extend the length of your accessory using the ZSP-12V-50B. This 50 feet RJ-45 cable also includes an extender

plug coupler to allow you to join connections to your existing accessory.

Q2: Is the ZWBMS-PRO compatible with Elite’s WhiteBoardScreen™ Series?

A: No, the ZWBMS-PRO is only compatible with Elite’s WhiteBoardScreen™ Universal Series.

Q3: Will any whiteboard cleaning product or whiteboard markers work on my Elite whiteboard screen?

A: For best results we strongly recommend using only Elite Screens whiteboard erasers and markers since the material is a

unique dual projection and dry-erase surface. Please see Elite’s whiteboard projection screen starter kit HERE

Q4: What is the frequency of your RF remote?

A: The frequency of the RF remote is 433MHz

Q5: I have a VMAX2 (Spectrum, Home2, CineTension2, VMAX Plus4) screen and a universal remote, what is

the code needed to control the screen with the remote?

A: Our IR remote controls have been evaluated and entered in to the databases of some Universal remote control

manufacturers. Please contact the manufacturer of your remote to inquire about your remote's ability to function with

ours. If they have not evaluated our remote control then the following list of Binary codes will be used for most remote

setups.

For Spectrum, VMAX2 (Plus), VMAX Plus4, Home2(3) and CineTension2(3) Series

Up: 1111 0000 0001

Stop: 1111 0000 0010

Down: 1111 0000 0100

For the VMAX2 User Guide please click HERE

Q6: What is the difference between an IR and an RF remote control?

A: The IR remote is an InfraRed remote. Infrared is based on the "light" part of the electromagnetic spectrum.

The RF remote is a Radio Frequency remote. Radio frequency is based on the "radio" section of the electromagnetic

spectrum.

While the IR remote control requires direct aim to the receiver in order for the signal to be received, the RF remote control

can be pointed in any direction to function as long as the signal is within range

Q7: How do I connect my Elite Screens ZSP-12 volt trigger RJ-45 adaptor to my projector and how does it

work?

A: See diagram below for wiring information.

Summary of content (6 pages)

PAGE 1
Elite Screens Frequently Asked Questions Screens FAQs Q1: How can I extend my RJ-45 accessory such as my 3-way wall switch, 5-12v trigger, and IR "eye" sensor? A: You can extend the length of your accessory using the ZSP-12V-50B. This 50 feet RJ-45 cable also includes an extender plug coupler to allow you to join connections to your existing accessory.
PAGE 2
ZSP-12V wiring diagram • Please note that the RJ-45 is exclusively designed to be compatible with only a projector’s trigger output. Any other type of device’s trigger output that you choose to utilize with our product is to your own discretion and is not covered under warranty should there be any malfunction. Please contact Elite Screen’s technical support department for further information.
PAGE 3
Q8: How do I sync my RF remote to my Elite electric screen A: If your RF remote control does not work with your screen, try the following to get in synced. See below for instructions. Make sure new batteries or working batteries are in your RF remote control before proceeding with the steps. For V 2.0 electric screens. The version number can be found on the remote control, the sticker on the screen's end cap, or the packing box. 1. Unplug your screen from the power outlet 2.
PAGE 4
Elite Screens Frequently Asked Questions Accessories FAQs Q1: How can I extend my RJ-45 accessory such as my 3-way wall switch, 5-12v trigger, and IR "eye" sensor? A: You can extend the length of your accessory using the ZSP-12V-50B. This 50 feet RJ-45 cable also includes an extender plug coupler to allow you to join connections to your existing accessory.
PAGE 5
ZSP-12V wiring diagram • Please note that the RJ-45 is exclusively designed to be compatible with only a projector’s trigger output. Any other type of device’s trigger output that you choose to utilize with our product is to your own discretion and is not covered under warranty should there be any malfunction. Please contact Elite Screen’s technical support department for further information.
PAGE 6
Q8: How do I sync my RF remote to my Elite electric screen A: If your RF remote control does not work with your screen, try the following to get in synced. See below for instructions. Make sure new batteries or working batteries are in your RF remote control before proceeding with the steps. For V 2.0 electric screens. The version number can be found on the remote control, the sticker on the screen's end cap, or the packing box. 1. Unplug your screen from the power outlet 2.