Instructions / Assembly

NOTE: Turn off power at circuit box to avoid possible electric shock.
SHADE INSTALLATION
Screwdriver and Pliers.
TOOLS REQUIRED
1. Remove the switch housing cover from the fan by unscrewing the screws (See figure 4).
You may keep this cover for future use.
2. Replace the two screws but thread only halfway into the switch housing
.
3. Locate two single wires in the switch housing, white (gray on some models) and blue
(red on some models) labeled “for light”.
4. Connect these wires to the light kit wires using the wire nuts already attached
(See figure 1). White (gray) to white and blue (red) to black.
5. NOTE: For French Canadian specs, please use the plug system (See figure 5). If
using
with a UL spec fan, please cut off plugs, and wire with wire nuts provided with the fan.
6. Carefully push all wires back into switch housing of fan. Attach the light kit by aligning
its keyhole slots with the two screws previously threaded halfwa
y into the switch housing
(See figure 1). Push up so the screws go
through the light kit's keyhole slots and twist so
that the screws engage into the smaller end of the slots.
Tighten the screws securely to
prevent light kit from vibrating loose.
7. Proceed to “Shade Installation”.
KEY HOLE INSTALLATION
1. Remove the switch housing cover from the fan by unscrewing the bottom mount
screws
(figure 4) or the side mount screws (figure 6).
2. Remove the plug (figure 6) from the center of this cover by unscrewing or pushing out.
You may discard the plug.
3. Attach the cover to the light kit threaded tube by first feeding the light kit wires (black and
white) through the hole in the cover and then screwing the cover onto the threaded tube
(See figure 7). Be sure it is tight enough to prevent the light kit from vibrating loose.
4. Place the lock washer and hex nut over the light kit wires onto the threaded tube, and
tighten the screw nut. (See figure 7).
5. Locate two single wires in switch housing, white (gray on some models) and blue
(red on
some models) labeled “for light”.
6. Connect these wires to the light kit wires using
the wire nuts already attached (See figure 2).
White (gray) to white and blue (red) to black.
7. NOTE: For French Canadian specs, please use the plug system (See figure 5). If
using
with a UL spec fan, please cut off plugs, and wire with wire nuts provided with fan.
8. Carefully push all wires back into the fan’s switch housing. Replace the cover with the
screws removed in step 1.
9. Proceed to “Shade Installation”.
UNIVERSAL INSTALLATION - Center Nipple Attachment
Integral Installation
The mounting of the light kit must be from the side and not the bottom (See figure 3).
Also, the holes in the fan’s switch housing must line up with the holes in the light kit.
Please refer to the Installation Instructions titled Integral Installation.
1. Remove the switch housing cover from the fan by unscrewing the screws. You may
keep
this cover for future use (See figure 4).
2. Remove adapter cup from top of the light kit by removing the screws on the side of the
light kit (See figure 8).
3. Locate two single wires in switch housing, white (gray on some models) and blue (red on
some models) labeled “for light”.
4. Connect these wires to the light kit wires using the wire nuts already attached
(See figure 3).
White (gray) to white and blue (red) to black.
5. NOTE: For French
Canadian specs, please use the plug system (See figure 5).
If using
with a UL spec fan, please cut off plugs, and wire with wire nuts provided with fan.
6. Carefully push the wiring connections back into the switch housing.
7. Using the cover plate mounting screws from step 1, attach the flush adapter portion of
light to the switch housing (See figure 3).
8. Proceed to “Shade Installation”.
INTEGRAL INSTALLATION
For three shade models by using fitter screw installation as seen in figure 9.
Install shades to light kit shade holders by finger tightening three sets of screws for each
shade holder. To avoid glass breakage, do not over tighten. Install 5W A15 LED medium
base light bulbs. Do not over tighten.
Restore electrical
power. Installation is complete.
If light kit does not work, turn off electricity and lower either canopy or decorative housing
on your ceiling fan to make sure the blue wire is connected to black household wire.
Please refer to electrical section on ceiling fan instruction manual.
TROUBLESHOOTING