User Guide

ManualsBrandsELITE ManualsOtherElite M2-6 Acoustic Amplifier with 4 Channels Mixer Effects and Bluetooth

Elite Acoustics Engineering

M2-6 or M26U* Acoustic Amplier with

4 Channels, Mixer, Effects,

and Bluetooth

Quick Guide Handbook

The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks

by Elite Acoustics Engineering, Inc is under license

NOTE: Due to continuous development and improvements of our products, features and specications are subject to

change without notice. All weights and measures are approximate. Oct 2021.

Elite Acoustics’ M2-6 , M26U* Acoustic Amplier with Mixer, Effects, and Bluetooth®

features an ergonomically sculpted cabinet for inclined-horizontal or vertical

placement; 6-1/2 inch woofer for superior bass response along with a 1 inch silk-

dome tweeter to deliver maximum clarity. M2-6 offers 4 input channels and 16

Digital Effects with a high-efciency Class D bi-amp. The Master Section contains

a 3-band EQ, Monitor Volume and stereo AUX input with level control. Selectable

Direct Out or Main Outputs are provided for seamless system expansion.

Summary of content (10 pages)

PAGE 1
Elite Acoustics Engineering M2-6 or M26U* Acoustic Amplifier with 4 Channels, Mixer, Effects, and Bluetooth® Quick Guide Handbook Elite Acoustics’ M2-6 , M26U* Acoustic Amplifier with Mixer, Effects, and Bluetooth® features an ergonomically sculpted cabinet for inclined-horizontal or vertical placement; 6-1/2 inch woofer for superior bass response along with a 1 inch silkdome tweeter to deliver maximum clarity. M2-6 offers 4 input channels and 16 Digital Effects with a high-efficiency Class D bi-amp.
PAGE 2
WHAT IS IN THE BOX Your M2-6 or M26U package contains the following: (1) Speaker M2-6 or M26U* (1) 12V AC Power Supply Adapter Refer to Page 2 and 4, for the following Controls QUICK START 1. Check that the Battery Switch [49] is set to the “Connect” position. (Battery Switch is a built in circuit breaker to preserve battery life.) 2. Make sure the SPEAKER VOLUME [3] control is turned all the way down. 3. Connect microphones and/or instruments. You can use Channel 1 or Channel 2, or both.
PAGE 3
TOP PANEL 3 2 +48V Power Mono Signal 1 5 8 Peak 0 10 -15 +15 -15 Clip Signal +15 Mid Low Monitor Level 6 4 7 -15 +15 9 Mute CH 1 CH 2 DRY CH 3/4 WET EFX Mix DECAY EFX Bypass 12 0 10 High RATE 10 Level AUX In E L I T E Flange R1 R2 R3 CHO ER2 R4 ER1 R5 E2 R6 E1 R7 R10 R9 R8 EFX A C O U S T I C S M2-6 - Live-Performance Monitor with 4 Channels, Mixer, Effects, and Bluetooth® 13 11 M2-6 EFFECTS R1 - Bright Cavern R2 - Dark Cavern R3 - Bright Hall R4 - Dark Hall R
PAGE 4
REAR PANEL CONTROLS Channel 1 [14] Gain: Apply gain for level control [15] Mute: Mute Channel [16] EFX/AUX Send Level: Adjust the level to “send” out [17] EFX/AUX select: select whether you are sending to internal EFX or external AUX bus [18] PAD: fixed attenuation for “hot” signals [19] Notch Filter: set amount of cut or boost for Notch Filter [20] Frequency: set the frequency of the Notch Filter [21] Phase: Reverse the phase of input waveform [22] Instr-Mic/Line: Select input source; Instrument or Mic/ Li
PAGE 5
REAR PANEL 51 Charge Only 3 2 1 Low Battery Level CHAN 1 Charge CHAN 2 Footswitch 19 20 10 50 60 Gain -10 +10 100 450 Notch Filter DC INPUT 12VDC 2A -10 +10 -10 +10 Connect Off On 250 5k EFX/AUX 30 42 Level 38 Mute Mid EFX Level 32 21 EFX AUX For Maximum Battery Life - Recharge after every use - Use & recharge battery at least once a month - Do not leave power switch in the “ON” position when it is not in use - Keep unit in a cool, dry place away from extreme temper
PAGE 6
DIGITAL EFX 16 DIGITAL EFX PROGRAMS • • • • • • • • • • • • • There are 16 total Digital EFX programs R1 to R10 - REVERB E1 and E2 - ECHO ER1 and ER2 - Echo and Reverb CHO - Chorus FLange - Flanger Program select Encoder (11) is for program change. Parameter knob (10) to change rate or delay time for the program that is set. Mix knob (9) is to fine turn the amount of EFX you want in output mix.
PAGE 7
SYSTEM SPECIFICATIONS Speakers: Woofer = 6 1/2” Tweeter = 1” Silk-Dome Optimized front ports for extended low-frequency response Frequency response 70Hz - 20k Hz Amplifier: Ultra High-Efficiency Class D 3 Original M2-6 units- 30W Bi-AMP New Production M26U* untis - 50 Watt Bi-Amp EQ Controls: Low +/- 12dB @ 50Hz (shelving) Mid +/- 12dB @ 200Hz – 4k Hz (resonant) High +/- 12dB @ 10k Hz (shelving) Notch +/- 12dB @ 80Hz – 400 Hz (high-Q resonant) Battery: Orginal M2-6 units - Built-in SLA type, recharg
PAGE 8
1. M26U - BATTERY & RECHARGING INFORMATION To fully charge a unit – a. Set Battery Switch to “CONNECT” b. Turn Power Switch OFF c. Connect “AC” adaptor to Power Jack. d. Blue “Charge” LED should be lit, Charge time can vary from 5 to 6 hours e. Once it is fully charged LED “Blue Color” will turn off. 2. 3. When unit is powered with “AC” adaptor, Battery Switch should be in “DISCONNECT” position if Battery is already fully charged.
PAGE 9
ORIGINAL M2-6 SLA BATTERY & RECHARGING INFORMATION 1. To fully charge a unit – a. Set Battery Switch to “CONNECT” b. Turn Power Switch OFF c. Connect “AC” adaptor to Power Jack. d. Blue “Charge” LED should be lit, Charge time can vary from 24 – 36 hours depending on model. 2. When unit is powered with “AC” adaptor, Battery Switch should be in “CONNECT” position. 3. Battery Switch should be on “DISCONNECT” when unit is packed for transit or unit is in storage.
PAGE 10
Legal Notice: CALIFORNIA PROPOSITION 65 WARNING WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov. THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS. 1. THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND 2. THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. WARRANTY (USA ONLY) Elite Acoustics Engineering Inc.