Important note to owner! P lease keep this m anual out of sight in a safe and secure location for your reference only...
Frequently Asked Questions 1) What are Arming Beeps? Normally you would expect Arming Beeps to sound when you set the Alarm, and again at the end of the Exit Delay Time. Arm Doors/Windows 2 Beeps Arm Motion Sensors 3 Beeps Arm Doors/Windows & Motion Sensors 4 Beeps Disarm 1 Beep (You may hear a different number of Beeps if buttons have been pressed quickly or repeatedly.) 2) How do I enter my Code to Disarm the system at the Control Panel? There are five Code Buttons, each representing two numbers.
6) How do I use my Remote? Unless otherwise informed by your installer, you will need to press the Lock button TWICE on the Remote to fully Arm the system. ONE press of the Unlock button is all that is needed to Disarm. You don’t need to press these buttons very hard, but rather press and hold until you see the small light (top left hand corner) flash on your Remote. To activate a ‘Panic Alarm’ from your Remote, press the Lock & Unlock buttons at the same time and hold these buttons down for 3 seconds.
10) How does the alarm use my Telephone Lines? Now you have the alarm installed, you are going notice some differences as you continue to use the telephones in your house.
Protect otector Elite 3 Securi Security System System ® User’s Manual Contents FCC Notices Introduction to Your Security System ............... 1 Security System Components ........................ 1 How You Communicate to Your System ............ 1 Control Panel .................................................. 1 Remote Handheld Touchpad........................... 1 Keychain Touchpad ........................................ 1 Telephone ........................................................
Declaration of Conformity The Protector® Security Group Ltd Building 3 Manufacturer’s Name: GE Interlogix, Inc. Manufacturer’s Address: 2266 North 2nd Street North St.
Introduction to Your Security System Keychain Touchpads are used to control the security system from within or near the outside of your home. Your security system uses wireless technology to warn your family about intrusion and fire. The system has the capabilities of communicating with a central monitoring station. Sensors This manual describes how to operate your system.
HOME SECURITY Doors & Motion Windows Sensors Arming Your System with No Entry Delay Note No Entry Delay can be used in two ways. You can use this feature when you’re staying at home, after you’ve armed the system (i.e. when you’re asleep). Second, you can use this when you’re away from your home. To avoid causing an alarm, you must disarm the system with a remote handheld touchpad or keychain before entering your home. Check with your installer to find out how this option is programmed.
HOME CONTROL oors Special Motion Time Sensor EMERGENCY On Off EMERGENCY HOME CONTROL Chime Lights The Home Control buttons are used to monitor activity within and around the home. They are not used for intrusion protection. If any of the Home Control buttons are pressed and a sensor or module is not associated (programmed) with this feature the panel will announce, Function not available.
Status Beeps ARM Doors/ Windows & Motion Sensors Panel Indicator Lights Exit delay and Entry delay beeps sound 4 times every 5 seconds and 4 times per second during the last 10 seconds (if Silent Exit is used, the Exit delay beeps will only sound 4 times when you arm and 4 times when the Exit delay expires) Button Chime Special Motion When the Button Light is On Motion will cause chime When the Button Flashes _________________ DISARM 1 beep CHIME DOORS 2 beeps (feature must be programmed by instal
turn security protection off. To subdisarm the system, enter the master access code.
Programming Your System 1. Press Down 2. Open Cover The programming decals are visible when you open the panel cover (see Figure 1.). These decals are designed to make system programming easier for you. Always begin by entering your access code. Then, choose an operation from the START MENU. Follow the voice prompts and flow arrows to complete the desired task. Notice the button flow diagrams following the Instruction Summary.
4. After pressing a button on the START MENU the system voice will prompt you to then use the MAIN MENU. The MAIN MENU includes the following buttons: ❑ ❑ ❑ ❑ Light Control Option # Sensor/Remote Access Code 6. Enter new numbers using the numbered keys. 7. Close the panel cover. How to Delete an Access Code: Delete Access Code Delete Press Press the appropriate button. Depending on the button you pressed, the system will prompt you to continue by pressing other buttons on the panel. 1.
1. Open panel cover. Panel announces, Use numbered keys to enter ID. 2. Enter Master Code using the numbered keys. Panel announces, Please select from Start Menu. 3. Press Add from the Start menu. Panel announces, Select from main menu. 4. Press Option #. Panel announces, Option 1, press again for next option or done to select 5. Press DONE. Panel announces, Option 1 is on. Option 41 - Voice Chime The panel will verbally announce which chime sensor has been tripped if the chime feature is on.
1. Open panel cover. Panel announces, Use numbered keys to enter ID. 2. Enter Master Code using the numbered keys. Panel announces, Please select from Start Menu. 3. Press Delete from the Start menu. Panel announces, Select from main menu 4. Press Option #. Panel announces, Option 1, press again for next option or done to select. 5. Press 42. Panel announces, Option 42, press again for next option or done to delete. 6. Press DONE. Panel announces, Option 42 deleted.
system will indicate this condition to you by causing the SYSTEM STATUS button to light. When you press this button, the system responds with, Sensor # Name tampered. Correct the problem by resetting the sensor. If this condition continues, call your security system dealer. Use the following table to trip devices: Testing Sensors Device Siren 1 or 2 Failure Call your security system dealer. System Access Alarm The panel cover was opened while the system was armed.
4. Follow the arrow from the Clock Set button to the Hours keys. 5. Press the Hours +/– keys and listen to the voice prompts. Stop when panel voice announces the correct hour. 6. Press the Minutes +/– keys and listen to the voice prompts. Stop when the panel announces the correct minutes. 7. Press Done. The panel will announce the set time. 8. Close the cover.
. Bedroom Living Room Hall Bedroom Hall A smoke detector should be located on each level. Dining Room Bedroom Living Room Basement Basement Dining Room Bedroom Kitchen Bedroom H Hall Living Room Bedroom Dining Room Kitchen TV Room Living Room Bedroom H Bedroom x Recreation Room Smoke detectors should be located between the sleeping area and the rest of the family living unit. In family living units with more than one sleeping area, locate a smoke detector at each area.
Installer’s Name Installer’s Mobile Contact No. LIST 1 Pressing ‘Arm Doors & Windows’ at the Control Panel turns the alarm on in the following areas… The first press of the Closed Padlock on your Keychain Remote will turn the alarm on in areas stated in List 1 only. LIST 2 Pressing ‘Arm Motion Sensors’ at the Control Panel turns the alarm on in the following areas… Pressing the Closed Padlock on your Keychain Remote a second time will also turn the alarm on in the areas stated in List 2.
Quick Reference Table How to … Disarm the System Subdisarm the System Arm Only - Doors & Windows Control Panel Disarm + Access Code Enter Access Code while system is disarmed Doors & Windows Press once Arm Arm Only – Motion Sensors Arm Doors, Windows & Motion Sensors Activate No Entry Delay Remote Handheld Touchpad Disarm Press once ARM Doors & Windows Press once Press * + Master Code + 1 Press * + Master Code + 1 Enter Access Code while system is disarmed Press once Arm Doors Doors Motion& D
