Owner`s manual

7
4. After pressing a button on the
START MENU
the
system voice will prompt you to then use the
MAIN
MENU.
The
MAIN MENU
includes the following buttons:
❑ Light Control
❑ Option #
❑ Sensor/Remote
❑ Access Code
Press the appropriate button. Depending on the button you
pressed, the system will prompt you to continue by press-
ing other buttons on the panel.
Access Codes
Your security system has a master access code, access
codes 1-5, and a panic code used for arming and disarming
the panel. The master code is used for disarming and pro-
gramming your system. Access codes 1-5 are generally
used for children or as temporary codes for a baby-sitter or
service personnel. The panic code may be entered to arm,
disarm or subdisarm the system in a non-medical emer-
gency situation. The panel will call the central station with
a panic alarm report, but there will be no indication of an
alarm at the panel.
Note
Codes are always needed to disarm the system.
Note
Because different codes can be entered using the
same button presses you have to use caution when
programming the panic code. You need to ensure
that the panic code does not use the same button
presses as other access codes. For example if the
master code is 1234, do not program the panic code
to be 2244. The panel would interpret these codes to
be the same code.
How to change an Access Code:
1.
Open the cover
of the panel.
2. The panel voice prompts you to Use numbered keys to
enter ID. Enter your master access code
using the
numbered keys.
3. The panel voice prompts you to Please select from
START MENU.
Press the Add button
on the START
MENU.
4. The panel voice prompts you to Select from MAIN
MENU.
Press the Access Code button
on the MAIN
MENU.
5. The panel voice responds with Master Code, press
again for next access code or DONE to select or
CANCEL to quit. Press the access code button again
to hear the next access code. When you hear the
access code you wish to change
press the DONE
Button.
6.
Enter new numbers
using the numbered keys.
7.
Close the panel cover
.
How to Delete an Access Code:
1.
Open the cover
of the panel.
2. The panel voice prompts you to Use numbered keys to
enter ID. Enter your master access code
using the
numbered keys.
3. The panel voice prompts you to Please select from
START MENU.
Press the Delete button
on the
START MENU.
4. The panel voice prompts you to Select from MAIN
MENU.
Press the Access Code button
on the MAIN
MENU.
5. The panel voice responds with Access Code 1, press
again for next access code or DONE to select or
CANCEL to quit. Press the access code button again
to hear the next access code. When you hear the
access code you wish to delete,
press the DONE But-
ton. The panel voice responds with Access Code X
deleted.
6.
Close the panel cover
.
Programming Options
The following table is a list of options you can change.
Press
Add
in the
START MENU
and follow the voice
prompts to turn an option on.
Press
Delete
in the
START MENU
to turn an option off.
When entering a single digit option number (1-9), you
must type a zero before the number (i.e. 01, 02, .....). All
option numbers must be 2 digits.
Option 01 - Status Beeps
Add this option to enable panel beeps. Status beeps are any
beeps (including chime beeps) that come from the panel.
See “Status Beeps”.
Add Access Code
Press
DONE
Code
Access
Add
then use red numbers
Programming Options
Option # Add Delete
01 - Panel Beeps On Off
02 - Panel Voice On Off
41 - Chime Voice On Off
42 - Speaker Volume 1 - 8 8
(highest)
55 - Status Beep Volume 1 - 10 7
Delete Access Code
Press
Delete
Access
Code
DONE