Owner`s manual

2
HOME SECURITY
The Home Security buttons are used to arm and disarm
doors, windows and motion sensors in your system. The
System Status button is used to give information on sys-
tem activity.
Arm
Turn on intrusion/burglary protection for your system. You
can arm door/window sensors, motion sensors or both
depending on the buttons you press.
Disarm
Turn off intrusion/burglary protection for your system.
Only intrusion/burglary sensors such as doors/windows
and motion are disarmed. Environmental sensors, such as
smoke, stay armed at all times.
System Status
Press to hear information about your system. If the button
is lit, there is a problem with the system. If the button is
blinking, an alarm has occurred. Press the button to hear
what is wrong with the system. (See “Status Beeps”.)
Exit Delay
Exit Delay is the amount of time the system gives you to
exit the home before the system is armed (between 5 and
254 seconds). This is programmed by the installer. When
you arm you will hear beeps during the exit delay (see the
table “Status Beeps” of this manual to determine the
meaning of panel/system beeps).
Your Exit Delay is set for ___ seconds.
Entry Delay
Entry Delay is the amount of time the system gives you to
disarm the system after entering the home. This is pro-
grammed by the installer. When you enter your home you
will hear beeps during the entry delay (see the table “Sta-
tus Beeps” of this manual to determine the meaning of
panel/system beeps).
Your Entry Delay is set for ___ seconds.
Subdisarm
If your system includes 24-hour protection sensors on
items such as gun or jewelry cases, you must subdisarm
the panel before accessing these areas to avoid causing an
alarm.
Arming Your System with Doors & Windows
1. Press Arm Doors & Windows button.
Panel announces, Doors and windows on,
Arm Doors &
Windows
light will be lit and the exit delay will begin.
Arming Your System with No Entry Delay
Note
No Entry Delay can be used in two ways. You can
use this feature when you’re staying at home, after
you’ve armed the system (i.e. when you’re asleep).
Second, you can use this when you’re away from
your home. To avoid causing an alarm, you must dis-
arm the system with a remote handheld touchpad or
keychain before entering your home. Check with
your installer to find out how this option is pro-
grammed.
1. Press
Arm Doors & Windows
button twice
Panel announces, Doors and windows on, no entry delay.
Arm Doors & Windows
light will blink and the exit delay
will begin.
Arm Motion Sensors
1. Press
Arm Motion Sensors
button once.
Panel announces, Motions on. Arm Motion Sensors
light
will be lit and the exit delay will begin..
Disarming Your System
1. Upon reentering your home the entry delay will begin.
2. Status beeps will sound.
3. Enter your access code using the
Code
buttons.
Panel announces, System disarmed and the
Disarm
light
will be lit.
Subdisarm Your System
1. Enter your Master Access Code while the system is
disarmed.
Panel announces, System disarmed. Disarm
button light
blinks and the system is subdisarmed. When you’ve fin-
ished accessing the protected areas, press the
Disarm
but-
ton again. Panel announces, System disarmed. Disarm
button light stops blinking. System is in Disarm mode.
CODE
There are 5
CODE
buttons located in the second row of
the panel. Each button represents 2 numbers. The left
CODE
button is
1/2
, which means that this button is
pressed when entering either 1 or 2. For example, if your
access code is
1-2-3-4
you must press the
1/2
button twice
and the
3/4
button twice to enter that access code.
Arm
HOME SECURITY
Disarm
Status
System
Sensors
Motion
Windows
Doors &
CODE
1 / 2 3 / 4 5 / 6 7 / 8
9 / 0